Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0239522 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and the radio and display receiver assembly itself will not function.

WIRING DIAGRAM

E232585E44
0.344,1.156 0.927,1.375 0.583,0.219 10 false Volume- 1.948,3.802 2.531,3.979 0.583,0.177 10 false Off hook 2.927,3.802 3.313,3.979 0.385,0.177 10 false Voice 1.021,4.823 2.958,5.052 1.938,0.229 10 false Steering Pad Switch Assembly 1.135,3.802 1.708,3.979 0.573,0.177 10 false On hook 1.115,1.156 1.708,1.333 0.594,0.177 10 false Volume+ 4.823,0.594 5.115,0.771 0.292,0.177 10 false AU1 4.823,1.708 5.229,1.875 0.406,0.167 10 false EAU 4.833,2.813 5.125,2.99 0.292,0.177 10 false AU2 6.354,0.677 6.729,0.854 0.375,0.177 10 false SW1 6.354,1.802 6.74,1.979 0.385,0.177 10 false SWG 6.354,2.906 6.729,3.083 0.375,0.177 10 false SW2 6.156,3.344 6.531,3.521 0.375,0.177 10 false F31 1.948,1.156 2.417,1.333 0.469,0.177 10 false Seek- 4.385,0.698 4.573,0.875 0.188,0.177 10 false z3 4.375,1.813 4.563,1.99 0.188,0.177 10 false z3 4.375,2.917 4.563,3.094 0.188,0.177 10 false z3 4.385,0.51 4.563,0.688 0.177,0.177 10 false 11 4.427,1.625 4.521,1.802 0.094,0.177 10 false 8 4.375,2.729 4.573,2.917 0.198,0.188 10 false 10 5.333,0.698 5.625,0.875 0.292,0.177 10 false F21 6.104,0.604 6.281,0.781 0.177,0.177 10 false 21 6.094,1.708 6.271,1.885 0.177,0.177 10 false 23 6.104,2.833 6.281,3.01 0.177,0.177 10 false 22 5.438,1.625 5.531,1.802 0.094,0.177 10 false 3 5.427,0.5 5.521,0.677 0.094,0.177 10 false 6 5.438,2.729 5.531,2.906 0.094,0.177 10 false 5 2.552,2.354 2.99,2.531 0.438,0.177 10 false MODE 4.573,3.375 5.458,3.927 0.885,0.552 10 false Spiral Cable with Sensor Sub-assembly 6.292,3.5 6.948,4.958 0.656,1.458 10 false Radio and Display Receiver Assembly 2.573,1.156 3.042,1.333 0.469,0.177 10 false Seek+ 5.333,1.813 5.625,1.99 0.292,0.177 10 false F21 5.333,2.917 5.625,3.094 0.292,0.177 10 false F21

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-21 (SW1) - F31-23 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
F31-22 (SW2) - F31-23 (SWG) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY