Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR(for Front)
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0243255 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Ultrasonic sensor*1
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Toyota parking assist-sensor system

·

Simple intelligent parking assist system


(Click here)
Front bumper assembly
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system


Change grille shutter control modes and/or perform initialization (w/ Exhaust Heat Recirculation System) Grille shutter system (Click here)

*1: If a front side ultrasonic sensor (LH, RH) is removed and installed or replaced, it is necessary to perform registration.

PROCEDURE

Hide 1.REMOVE FRONT BUMPER ASSEMBLY

Hide 89341M 2.REMOVE FRONT SIDE ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342064

Disconnect the connector.


b.
E342065C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the front side ultrasonic sensor as shown in the illustration.


Hide 89348J 3.REMOVE ULTRASONIC SENSOR CLIP

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342068C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clamp.


b.

Disengage the 4 claws and remove the ultrasonic sensor clip as shown in the illustration.


Hide 89341K 4.REMOVE FRONT CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342070

Disconnect the connector.


b.
E342071C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the front corner ultrasonic sensor as shown in the illustration.


Hide 89341L 5.REMOVE FRONT CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342049

Disconnect the connector.


b.
E342050C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the front center ultrasonic sensor as shown in the illustration.


Hide 89347D 6.REMOVE FRONT SIDE ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front side ultrasonic sensor retainer is necessary.

·

When removing the front side ultrasonic sensor retainer, heat the front bumper assembly and front side ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the front bumper assembly and front side ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Side Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E342061

Remove the front side ultrasonic sensor retainer.


Hide 89347B 7.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

When removing the front corner ultrasonic sensor retainer, heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E342073

Remove the front corner ultrasonic sensor retainer.