Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR(for Front)
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0243255 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  INSTALLATION  


PROCEDURE

Hide 89347B 1.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

If a front corner ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the front bumper cover.

i.

Remove any remaining double-sided tape from the front bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 25 mm (0.984 in.)


Cover the sensor installation hole with a 25 mm (0.984 in.) circular piece of tape.


c.
E342074C01
2.115,0.865 2.49,0.698 false 2.51,0.594 2.729,0.781 0.219,0.188 10 true *a
*a Line
V100145

Primer


Using a brush or felt, apply primer or equivalent to the front corner ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the front bumper assembly until the primer has dried.




d.

Peel off the release paper from the front corner ultrasonic sensor retainer.


e.
E342067C01
2.208,0.885 2.573,0.688 false 2.594,0.573 2.823,0.76 0.229,0.188 10 true *a
*a Line
V100155

Press area


Align the front corner ultrasonic sensor retainer with the mark on the front bumper cover and install it as shown in the illustration.

NOTICE:

The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new front corner ultrasonic sensor retainer when reattachment is necessary.


HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front corner ultrasonic sensor retainer to the front bumper cover. Confirm there is no clearance between the front corner ultrasonic sensor retainer and front bumper cover.



Hide 89347D 2.INSTALL FRONT SIDE ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front side ultrasonic sensor retainer is necessary.

·

If a front side ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the front bumper cover.

i.

Remove any remaining double-sided tape from the front bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 25 mm (0.984 in.)


Cover the sensor installation hole with a 25 mm (0.984 in.) circular piece of tape.


c.
E342062C01
1.458,0.792 1.813,0.5 false 1.833,0.396 2.042,0.583 0.208,0.188 10 true *a
*a Line
V100145

Primer


Using a brush or felt, apply primer or equivalent to the front side ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the front bumper assembly until the primer has dried.




d.

Peel off the release paper from the front side ultrasonic sensor retainer.


e.
E342063C01
1.99,0.74 2.333,0.552 false 2.344,0.458 2.531,0.635 0.188,0.177 10 true *a
*a Line
V100155

Press area


Align the front side ultrasonic sensor retainer with the mark on the front bumper cover and install it as shown in the illustration.

NOTICE:

The double-sided tape of a front side ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new front side ultrasonic sensor retainer when reattachment is necessary.


HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front side ultrasonic sensor retainer to the front bumper cover. Confirm there is no clearance between the front side ultrasonic sensor retainer and front bumper cover.



Hide 89341L 3.INSTALL FRONT CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342051C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the front center ultrasonic sensor as shown in the illustration.


b.

Connect the connector.


Hide 89341K 4.INSTALL FRONT CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342072C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the front corner ultrasonic sensor as shown in the illustration.


b.

Connect the connector.


Hide 89348J 5.INSTALL ULTRASONIC SENSOR CLIP

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342069C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws to install the ultrasonic sensor clip as shown in the illustration.


b.

Engage the clamp.


Hide 89341M 6.INSTALL FRONT SIDE ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342066C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the front side ultrasonic sensor as shown in the illustration.


b.

Connect the connector.


Hide 7.INSTALL FRONT BUMPER ASSEMBLY