Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR(for Rear)
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0243256 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Ultrasonic sensor*1
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Toyota parking assist-sensor system

·

Simple intelligent parking assist system


(Click here)
Rear bumper assembly
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system



*1: If a rear side ultrasonic sensor (LH, RH) is removed and installed or replaced, it is necessary to perform registration.

PROCEDURE

Hide 1.REMOVE REAR BUMPER ASSEMBLY

Hide 89342B 2.REMOVE REAR SIDE ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342052

Disconnect the connector.


b.
E342053C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the rear side ultrasonic sensor as shown in the illustration.


Hide 89342 3.REMOVE REAR CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342078

Disconnect the connector.


b.
E342079C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the rear corner ultrasonic sensor as shown in the illustration.


Hide 89342A 4.REMOVE REAR CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342057

Disconnect the connector.


b.
E342055C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the rear center ultrasonic sensor as shown in the illustration.


Hide 89348T 5.REMOVE REAR SIDE ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear side ultrasonic sensor retainer is necessary.

·

When removing the rear side ultrasonic sensor retainer, heat the rear bumper assembly and rear side ultrasonic sensor retainer using a heat light.



a.

Heat the rear bumper assembly and rear side ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Side Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.

Remove the 2 rear side ultrasonic sensor retainers.

E343307C02
0.844,0.063 1.219,0.302 0.375,0.24 12 false *A 4,0.063 4.375,0.302 0.375,0.24 12 false *B
*A for RH Side *B for LH Side



Hide 89348R 6.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E342075

Remove the rear corner ultrasonic sensor retainer.


Hide 89348S 7.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.



a.

Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Center Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.

Remove the 2 rear center ultrasonic sensor retainers.

E338236