Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING
RM3210E _59 Vehicle Exterior _047542 EXTERIOR PANELS / TRIM _0243317 FRONT DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR WINDOW FRAME MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75752C 1.INSTALL FRONT DOOR FRONT WINDOW FRAME MOULDING

a.

Using an air riveter or hand riveter with a nose piece, install the front door front window frame moulding with 2 new rivets.

B436036

NOTICE:

To prevent damage, when installing the front door front window frame moulding, make sure that there are enough people available to hold it securely.


HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B125583C11
1.292,0.281 1.438,0.281 1.438,0.281 1.781,0.74 false 1.875,1.271 1.875,1.823 false 1.125,0.208 1.438,0.365 0.313,0.156 10 false *a 1.823,1.875 2.135,2.094 0.313,0.219 10 false *b 2.063,0.063 2.385,0.302 0.323,0.24 10 false *c
*a Riveter
*b Mandrel
*c Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C10
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 1.479,0.365 1.802,0.604 0.323,0.24 10 false *a 2.198,0.125 2.51,0.365 0.313,0.24 10 false *b 2.052,1.146 2.365,1.385 0.313,0.24 10 false *b 1.531,1.313 1.854,1.552 0.323,0.24 10 false *a
*a Riveter
*b Incorrect


Confirm that the rivets are seated properly against the moulding.

·

Do not tilt the riveter when installing the rivet to the moulding.

·

Do not leave any space between the rivet head and moulding.

·
B125585C10
1.135,0.771 1.396,0.771 false 1.438,0.667 1.75,0.938 0.313,0.271 10 false *a 2.01,0.188 2.344,0.469 0.333,0.281 10 false *b
*a Riveter
*b Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




b.
B436034C01
0.802,3.198 1.365,2.594 1.365,2.594 0.813,2.604 true 2.729,0.385 2.115,0.292 2.115,0.292 2.75,0.771 true 1.385,2.49 1.625,2.729 0.24,0.24 10 true *a 3.01,2.656 3.323,2.813 0.313,0.156 10 false *b 1.917,0.198 2.156,0.438 0.24,0.24 10 true *a
*a Bolt <A>
*b Bolt <B>


Install the front door panel sub-assembly with the 4 bolts <A>.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

To prevent damage, when installing the front door panel sub-assembly, make sure that there are enough people available to hold it securely.



c.

Apply adhesive to the threads of the bolt <B>.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the bolt <B>.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


e.
B435280C01
2.365,0.958 2.708,0.958 true 1.865,2.948 2.208,2.948 true 1.26,3.479 0.563,2.823 0.563,2.823 1.26,2.427 false 1.813,4.323 1.813,4.448 true 2.208,4.208 2.563,4.042 true 1.229,1.563 0.615,1.01 0.615,1.01 1.01,0.51 false 0.448,3.979 0.823,4.229 0.375,0.25 12 false *A 2.76,0.875 3.073,1.031 0.313,0.156 10 false *1 2.26,2.875 2.573,3.031 0.313,0.156 10 false *2 1.729,4.458 2.042,4.615 0.313,0.156 10 false *a 2.625,3.969 2.938,4.125 0.313,0.156 10 false *b 0.365,2.75 0.677,2.906 0.313,0.156 10 false *b 0.406,0.927 0.719,1.083 0.313,0.156 10 false *b
*A Section
*1 Front Door Upper Hinge Assembly
*2 Front Door Lower Hinge Assembly
*a Front Door Hinge Assembly
*b Anti-rust Coating


Using a brush, apply anti-rust coating to each front door hinge assembly as shown in the illustration.


f.

Connect each connector.


g.

Engage each clamp.


Hide 62112 2.INSTALL COWL SIDE TRIM BOARD

Hide 67914 3.INSTALL FRONT DOOR SCUFF PLATE

Hide 75754A 4.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

a.

Engage the guide to temporarily install the front door upper window frame moulding to the door frame.

B436033


b.

Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding with 6 new rivets.

HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B125583C11
1.292,0.281 1.438,0.281 1.438,0.281 1.781,0.74 false 1.875,1.271 1.875,1.823 false 1.125,0.208 1.438,0.365 0.313,0.156 10 false *a 1.823,1.875 2.135,2.094 0.313,0.219 10 false *b 2.063,0.063 2.385,0.302 0.323,0.24 10 false *c
*a Riveter
*b Mandrel
*c Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C10
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 1.479,0.365 1.802,0.604 0.323,0.24 10 false *a 2.198,0.125 2.51,0.365 0.313,0.24 10 false *b 2.052,1.146 2.365,1.385 0.313,0.24 10 false *b 1.531,1.313 1.854,1.552 0.323,0.24 10 false *a
*a Riveter
*b Incorrect


Confirm that the rivets are seated properly against the moulding.

·

Do not tilt the riveter when installing the rivet to the moulding.

·

Do not leave any space between the rivet head and moulding.

·
B125585C10
1.135,0.771 1.396,0.771 false 1.438,0.667 1.75,0.938 0.313,0.271 10 false *a 2.01,0.188 2.344,0.469 0.333,0.281 10 false *b
*a Riveter
*b Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




Hide 68126 5.INSTALL FRONT DOOR FIX WINDOW GLASS

Hide 67402F 6.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

Hide 68151D 7.INSTALL FRONT DOOR GLASS RUN

Hide 67862 8.CONNECT FRONT DOOR WEATHERSTRIP

a.

Engage the 2 clips and connect the front door weatherstrip.


Hide 75756C 9.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:

When installing a new front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Door Rear Window Frame Moulding 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body or front door rear window frame moulding excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B436031C01
1.292,1.146 1.667,1.313 true 1.938,1.875 2.313,2.042 true 1.521,2.229 2.281,2.563 true 1.021,1.01 1.302,1.24 0.281,0.229 10 true *a 2.313,2.49 2.573,2.698 0.26,0.208 10 true *b 2.365,1.99 2.646,2.219 0.281,0.229 10 true *a
*a Double-sided Tape
*b Caulking Sponge


Install a new front door rear window frame moulding.

i.

Using a heat light, heat the vehicle body and front door rear window frame moulding.


ii.

Remove the release paper from the front door rear window frame moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the clip and guide and attach the double-sided tape and caulking sponge to install the front door rear window frame moulding.

HINT:

Press the front door rear window frame moulding firmly to install it.




Hide 75720 10.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY