Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM3210E _59 Vehicle Exterior _047505 DOOR / HATCH _0244373 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 75752C 2.INSTALL FRONT DOOR FRONT WINDOW FRAME MOULDING

Hide 62112 3.INSTALL COWL SIDE TRIM BOARD

Hide 67914 4.INSTALL FRONT DOOR SCUFF PLATE

Hide 75976G 6.INSTALL FRONT DOOR LOWER OUTSIDE STRIPE (w/ Black Out Tape)

Hide 75986B 7.INSTALL FRONT DOOR STRIPE (w/ Black Out Tape)

Hide 75966B 8.INSTALL FRONT DOOR REAR OUTSIDE STRIPE (w/ Black Out Tape)

Hide 75754A 9.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75756C 10.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 75720 11.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

Hide 67837B 12.INSTALL FRONT DOOR DUST PROOF SEAL

a.
B436622

Engage the 3 claws to install 3 new front door dust proof seals.


Hide 67001A 13.INSTALL FRONT DOOR PANEL CUSHION

a.
B436621

Engage the 4 claws to install 2 new front door panel cushions.


Hide 68126 14.INSTALL FRONT DOOR FIX WINDOW GLASS

a.

Install the front door fix window glass to the front door fix window weatherstrip.


b.
B436620C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door fix window glass with the front door fix window weatherstrip as shown in the illustration.


Hide 67402F 15.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B436618C02
0,0 0,0 false
V100135

Bolt
V100136

Screw


Install the front door front lower frame sub-assembly with the 3 bolts and screw.

Torque:
Bolt : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Screw : 3.1 N*m (32 kgf*cm, 27 in.*lbf)


Hide 67664C 16.INSTALL DOOR FRAME GARNISH

a.
B436589

Engage the 3 claws to install the door frame garnish.


Hide 67862 17.INSTALL FRONT DOOR WEATHERSTRIP

a.
B442202

Engage the 21 clips and install the front door weatherstrip.


Hide 68610 18.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door check assembly.


b.

Clean the bolt hole in the vehicle body.


c.

Clean the threads of the bolt (B).


d.

Apply adhesive to the threads of the bolt (B).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
B436616N01
1.51,0.51 1.667,0.708 0.156,0.198 10 true A 1.479,1.458 1.635,1.656 0.156,0.198 10 true A 2.135,1.51 2.292,1.708 0.156,0.198 10 true B

Install the front door check assembly with the 3 bolts.

Torque:
Bolt (A) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 69312 19.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B442174C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 69202A 20.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B436614C01
0.073,0.073 0.531,0.49 0.458,0.417 12 false *A 0.073,2.542 0.521,2.938 0.448,0.396 12 false *B
*A Outside
*B Inside


Engage the claw as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69040A 21.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69242E 22.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B436611

Engage the 3 guides.


b.

Engage the claw to install the front door rear outside handle pad.


Hide 69241H 23.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B436610

Engage the 3 claws to install the front door front outside handle pad.


Hide 69217E 24.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B436609

Engage the 2 guides and claw.


b.

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B433543

Install the hole plug.


Hide 25.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B436608

Using a T30 "TORX" socket wrench, install the front door lock cylinder assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B433544

Install the hole plug.


Hide 69220 26.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B436607C01
0,0 0,0 false
V113147

Install in this Direction


Insert the front end of the front door outside handle assembly into the front door outside handle frame sub-assembly.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame sub-assembly, then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.
B436605C01
0,0 0,0 false
V113147

Engage in this Direction


Move the lever as shown in the illustration and engage the 2 claws to secure the front door outside handle assembly.


d.
B436612

Engage the 3 clamps.


e.
B436603

Connect the connector.


f.

Engage the 2 claws.


Hide 67404F 27.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B436601C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


b.

Install the front door rear lower frame sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 68151D 28.INSTALL FRONT DOOR GLASS RUN

a.
B436599

Install the front door glass run.


Hide 29.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.

Temporarily install the temporary bolt to the front door window regulator assembly.


c.
B436598C01
1.615,0.427 2.24,0.896 true 1.354,0.271 1.594,0.49 0.24,0.219 10 true *a 2.521,1.563 2.688,1.75 0.167,0.188 10 true 1 2.323,0.146 2.49,0.333 0.167,0.188 10 true 2 2.875,1.396 3.042,1.583 0.167,0.188 10 true 3 2.01,0.313 2.177,0.5 0.167,0.188 10 true 4 0.781,0.813 0.948,1 0.167,0.188 10 true 5 1.531,0.583 1.698,0.771 0.167,0.188 10 true 6
*a Temporary Bolt


Temporarily install the front door window regulator assembly with the 5 bolts.


d.

Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


f.
B436596

Engage the 2 claws to install the front door No. 2 service hole cover.


Hide 68102 30.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

for Driver Side:

i.

Connect the multiplex network master switch assembly.



b.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.

Move the front door window regulator assembly so that the door glass bolt holes can be seen.


f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

for Driver Side:

i.

Disconnect the multiplex network master switch assembly.



i.

for Front Passenger Side:

i.

Disconnect the power window regulator switch assembly.



j.
B439192C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.


k.
B436594

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


l.
B436593

Install the hole plug.


Hide 67832 32.INSTALL FRONT DOOR SERVICE HOLE COVER

a.
B436592

Engage the 4 clips to install a new front door service hole cover.


b.
B436591

Insert 3 new front door weatherstrip clips and turn them 45 degrees as shown in the illustration to install them.


Hide 86160 33.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67836C 34.INSTALL FRONT DOOR NO. 3 SERVICE HOLE COVER

a.
B436623

Install the front door No. 3 service hole cover.


Hide 87940 35.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

Hide 67856B 36.INSTALL FRONT DOOR PANEL PROTECTOR

Hide 67838D 37.INSTALL FRONT DOOR VENT SEAL

a.
B442178C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door vent seal to the front door inner glass weatherstrip.


Hide 38.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

a.
B436587C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door inner glass weatherstrip with front door vent seal as shown in the illustration.


b.
B436585

Engage the clip.


Hide 69206B 39.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B436588

Engage the 2 claws to install the front door inside handle sub-assembly.


Hide 67602 40.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B436584C01
2.406,1.271 2.708,0.99 false 2.552,1.958 2.292,1.604 false 2.719,0.896 2.958,1.083 0.24,0.188 10 true *1 2.573,1.917 2.885,2.115 0.313,0.198 10 false *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly
V113147

Install in this Direction


Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle sub-assembly as shown in the illustration.


b.
B436582

Engage the guide and 6 claws.


c.

Engage the 10 clips to install the front door trim board sub-assembly.


d.
B436581

Install the 3 screws.


Hide 81230 41.INSTALL COURTESY LIGHT ASSEMBLY

Hide 42.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

a.

Connect the connector.


b.
B436580C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 clips and 4 claws to install the multiplex network master switch assembly with front door upper armrest base panel as shown in the illustration.


Hide 43.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B436578C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 clips and 4 claws to install the power window regulator switch assembly with front door upper armrest base panel as shown in the illustration.


Hide 74220 44.INSTALL FRONT ARMREST ASSEMBLY

a.
B439205C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


b.
B436576C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 clips and 7 claws to install the front armrest assembly as shown in the illustration.


Hide 69284F 45.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B435680

Engage the 3 claws to install the front door inside handle bezel plug.


Hide 46.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION


Hide 47.INITIALIZE POWER WINDOW CONTROL SYSTEM