Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE(for Front Side)
RM3210E _54 Brake _047522 PARKING BRAKE _0243350 PARKING BRAKE CABLE(for Front Side) A

PARKING BRAKE  PARKING BRAKE CABLE(for Front Side)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during No. 1 parking brake cable assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of brake pedal stroke sensor assembly
1.

Clear the data stored during previous linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

2.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:(Click here)
for calibration:(Click here)

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 46250 1.REMOVE PARKING BRAKE PEDAL ASSEMBLY (for LHD)

Hide 46250 2.REMOVE PARKING BRAKE PEDAL ASSEMBLY (for RHD)

Hide 58991B 3.REMOVE FRONT CONSOLE BOX MOUNTING BRACKET

a.
C345642

Disengage the 2 clamps.


b.

Remove the 2 bolts and front console box mounting bracket.


Hide 8598B 4.REMOVE INVERTER BATTERY (w/ Canister Pump Module)

Hide 46410 5.SEPARATE NO. 1 PARKING BRAKE CABLE ASSEMBLY

a.
C346590C02
0.771,0.573 1.333,0.573 true 2.177,0.344 2.74,0.344 true 0.573,0.49 0.771,0.656 0.198,0.167 10 true *a 2.75,0.25 2.958,0.438 0.208,0.188 10 true *b
*a Turn
*b Hold


Separate the No. 1 parking brake cable assembly from the No. 1 parking brake pull rod sub-assembly as shown in the illustration.


Hide 46410 6.REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)

a.

Disengage the 2 clamps.

C345669C01
5.906,2.042 6.063,1.813 6.063,1.813 6.271,1.813 true 6.281,1.719 6.438,1.917 0.156,0.198 10 true *1
*1 Front Parking Brake Cable Clamp - -


HINT:

The front parking brake cable clamp cannot be reused once removed. Make sure to remove it from the No. 1 parking brake cable clamp assembly.



b.

Remove the 4 bolts and No. 1 parking brake cable assembly.


Hide 46410C 7.REMOVE FRONT PARKING BRAKE CABLE CLAMP (for LHD)

a.

for One-piece type front parking brake cable clamp:

i.

Using pliers or equivalent, disconnect the front parking brake cable clamp and remove it from the No. 1 parking brake cable assembly.



b.

for Separate type front parking brake cable clamp:

i.
C348422

Disengage the 2 claws to remove the front parking brake cable clamp from the No. 1 parking brake cable assembly.



Hide 46410 8.REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for RHD)

a.
C345644

Disengage the clamp.


b.

Remove the 3 bolts and No. 1 parking brake cable assembly.