Home › Brake › PARKING BRAKE › PARKING BRAKE PEDAL(for LHD)
RM3210E _54 Brake _047522 PARKING BRAKE _0243348 PARKING BRAKE PEDAL(for LHD) A

PARKING BRAKE  PARKING BRAKE PEDAL(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during parking brake pedal assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of brake pedal stroke sensor assembly
1.

Clear the data stored during previous linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

2.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:(Click here)
for calibration:(Click here)

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 46441 3.LOOSEN NO. 1 WIRE ADJUSTING NUT

a.
C345658

Loosen the No. 1 wire adjusting nut.

NOTICE:

If the No. 1 wire adjusting nut has been removed from the No. 1 parking brake cable assembly, replace the No. 1 wire adjusting nut with a new one.



Hide 55606 4.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 58910C 5.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 55406B 6.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 58816C 7.REMOVE FRONT NO. 1 CONSOLE BOX INSERT

Hide 58817B 8.REMOVE FRONT NO. 2 CONSOLE BOX INSERT

Hide 87211 9.REMOVE NO. 1 AIR DUCT

Hide 67914 10.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 11.REMOVE COWL SIDE TRIM BOARD LH

Hide 55436A 12.REMOVE INSTRUMENT PANEL FINISH PANEL END LH

Hide 55470 13.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 53601 14.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55480D 15.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 89510D 16.REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY

Hide 46410 17.SEPARATE NO. 1 PARKING BRAKE CABLE ASSEMBLY

a.
C345665

Remove the nut and separate the No. 1 parking brake cable assembly.


Hide 46250 18.SEPARATE PARKING BRAKE PEDAL ASSEMBLY

a.
C345666

Disengage the clamp.


b.

Disconnect the parking brake switch connector.


c.
C345667

Remove the bolt and 2 nuts, and separate the parking brake pedal assembly from the vehicle body.


Hide 46250 19.REMOVE PARKING BRAKE PEDAL ASSEMBLY

a.
C345636

Pull up the parking brake pedal assembly claw.

NOTICE:

Do not damage the No. 1 parking brake cable assembly.



b.
C345637

Remove the No. 1 wire adjusting nut from the No. 1 parking brake cable assembly.

NOTICE:

If the No. 1 wire adjusting nut has been removed from the No. 1 parking brake cable assembly, replace the No. 1 wire adjusting nut with a new one.



c.
C345638

Remove the clip from the No. 1 parking brake cable assembly.


d.

Remove the parking brake pedal assembly from the No. 1 parking brake cable assembly.