Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM3210E _56 Audio / Visual / Telematics _047510 AUDIO / VIDEO _0243397 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E341811E01
5.406,6.01 7.115,6.542 1.708,0.531 10 false Radio and Display Receiver Assembly 5.885,5.177 6.792,5.635 0.906,0.458 10 false ILL- 5.552,5.156 6.458,5.615 0.906,0.458 10 false F33 5.615,4.979 6.521,5.438 0.906,0.458 10 false 5 3.469,3.229 4.375,3.688 0.906,0.458 10 false PANEL 0.375,3.063 2,3.521 1.625,0.458 10 false from TAIL Relay 5.531,1.083 6.438,1.542 0.906,0.458 10 false F31 5.542,0.51 6.448,0.969 0.906,0.458 10 false F32 5.563,0.313 6.469,0.771 0.906,0.458 10 false 10 5.583,0.896 6.49,1.354 0.906,0.458 10 false 23 5.885,1.073 6.792,1.531 0.906,0.458 10 false SWG 5.885,0.521 6.792,0.979 0.906,0.458 10 false ILL+ 3.708,0.51 4.615,0.969 0.906,0.458 10 false F21 3.698,1.083 4.604,1.542 0.906,0.458 10 false F21 3.719,0.323 4.625,0.781 0.906,0.458 10 false 13 3.771,0.896 4.677,1.354 0.906,0.458 10 false 3 2.708,1.083 3.615,1.542 0.906,0.458 10 false z3 2.698,0.51 3.604,0.969 0.906,0.458 10 false z3 2.74,0.885 3.646,1.344 0.906,0.458 10 false 8 2.729,0.333 3.635,0.792 0.906,0.458 10 false 5 3.156,0.406 4.063,0.865 0.906,0.458 10 false Il+2 3.146,0.969 4.052,1.427 0.906,0.458 10 false EAU 2.594,1.5 4.135,1.99 1.542,0.49 10 false Spiral Cable with Sensor Sub-assembly 0.406,2.344 2.823,2.802 2.417,0.458 10 false Steering Pad Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
Illumination comes on only for steering pad switch assembly. C
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). D




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

D

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the F21 spiral cable with sensor sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F21-13 (IL+2) - Body ground Power switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the F32 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F32-10 (ILL+) - Body ground Power switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)
a.

Disconnect the F33 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F33-5 (ILL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR