Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM3210E _56 Audio / Visual / Telematics _047510 AUDIO / VIDEO _0243397 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL): (for 6 Speakers)

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based on vehicle speed signals sent from the meter circuit plate.


for "Bluetooth":

Vehicle speed signals are sent from the meter circuit plate and used to cancel "Bluetooth" function operation.

The radio and display receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


for Digital Versatile Disc (DVD):

The radio and display receiver assembly receives a vehicle speed signal from the meter circuit plate for DVD viewing restriction while driving, etc.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the meter circuit plate. The signal is changed to a pulse signal at the transistor in the meter circuit plate. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E342182E01
1.531,2.115 1.99,2.313 0.458,0.198 10 false SPD 1.531,0.229 1.99,0.427 0.458,0.198 10 false SP1 1.927,0.208 2.385,0.406 0.458,0.198 10 false 11 1.917,2.104 2.375,2.302 0.458,0.198 10 false 19 1.542,4.958 2,5.156 0.458,0.198 10 false SPD 1.906,4.958 2.365,5.156 0.458,0.198 10 false 11 2.802,2.021 3.26,2.219 0.458,0.198 10 false 19 4.302,2.01 4.76,2.208 0.458,0.198 10 false 16 4.302,3.479 4.76,3.677 0.458,0.198 10 false 18 5.313,0.208 5.771,0.406 0.458,0.198 10 false 20 5.594,0.323 6.052,0.521 0.458,0.198 10 false SI 5.594,2.219 6.052,2.417 0.458,0.198 10 false +S 5.313,2.104 5.771,2.302 0.458,0.198 10 false 19 5.313,3.563 5.771,3.76 0.458,0.198 10 false 17 5.594,3.583 6.052,3.781 0.458,0.198 10 false SPD 5.615,4.938 6.073,5.135 0.458,0.198 10 false SPD 5.313,4.927 5.771,5.125 0.458,0.198 10 false 17 0.323,0.844 0.781,1.042 0.458,0.198 10 false A41 0.302,1.01 2.375,1.427 2.073,0.417 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.417,2.521 2.208,2.948 1.792,0.427 10 false Certification ECU (Smart Key ECU Assembly) 0.438,2.365 0.896,2.563 0.458,0.198 10 false F1 0.417,5.208 0.875,5.406 0.458,0.198 10 false F61 0.406,5.375 2.208,5.729 1.802,0.354 10 false Stereo Component Amplifier Assembly*3 5.135,2.375 5.594,2.573 0.458,0.198 10 false F6 5.135,2.531 6.969,2.958 1.833,0.427 10 false Combination Meter Assembly (Meter Circuit Plate) 2.792,4.854 3.25,5.052 0.458,0.198 10 false 17 2.635,5.719 4.49,5.948 1.854,0.229 10 false No. 17 Junction Connector*5 5.073,3.844 5.531,4.042 0.458,0.198 10 false F92 5.323,5.396 7.042,5.865 1.719,0.469 10 false Radio and Display Receiver Assembly*2 5.073,4 7.156,4.208 2.083,0.208 10 false Navigation Receiver Assembly*1 5.031,5.396 5.49,5.594 0.458,0.198 10 false F31 2.667,6.125 4.75,6.333 2.083,0.208 10 false *2: for Radio and Display Type 0.344,6.115 2.427,6.323 2.083,0.208 10 false *1: for Navigation Receiver Type 3.99,2.01 4.448,2.208 0.458,0.198 10 false 7 3.958,3.479 4.417,3.677 0.458,0.198 10 false 10 2.427,2.021 2.885,2.219 0.458,0.198 10 false 11 2.469,4.854 2.656,5.094 0.188,0.24 10 false 9 4.271,2.208 4.729,2.406 0.458,0.198 10 false F85 4.271,3.677 4.729,3.875 0.458,0.198 10 false F85 2.76,2.219 3.219,2.417 0.458,0.198 10 false F85 2.75,5.063 3.208,5.26 0.458,0.198 10 false F85 3.906,2.208 4.177,2.417 0.271,0.208 10 false F79 3.917,3.677 4.188,3.885 0.271,0.208 10 false F79 2.385,2.219 2.656,2.427 0.271,0.208 10 false F79 2.396,5.063 2.667,5.271 0.271,0.208 10 false F79 2.646,5.438 4.5,5.667 1.854,0.229 10 false No. 8 Junction Connector*4 4.854,6.146 6.104,6.333 1.25,0.188 10 false *3: for 10 Speakers 1.677,6.469 2.542,6.677 0.865,0.208 10 false *5: for RHD 0.354,6.458 1.219,6.667 0.865,0.208 10 false *4: for LHD 2.438,2.417 2.615,2.625 0.177,0.208 10 false *4 2.438,5.271 2.615,5.479 0.177,0.208 10 false *4 3.948,2.406 4.125,2.615 0.177,0.208 10 false *4 3.958,3.885 4.135,4.094 0.177,0.208 10 false *4 2.792,2.427 2.969,2.635 0.177,0.208 10 false *5 4.313,2.417 4.49,2.625 0.177,0.208 10 false *5 4.313,3.885 4.49,4.094 0.177,0.208 10 false *5 2.802,5.271 2.979,5.479 0.177,0.208 10 false *5

PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E227878

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal Check Mode in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

While driving the vehicle, compare the value of "SPEED" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The meter circuit plate receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values in the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the actual vehicle speed measured using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT METER CIRCUIT PLATE (OUTPUT WAVEFORM)
2.INSPECT METER CIRCUIT PLATE (OUTPUT WAVEFORM)
a.

Check the output waveform.

E265790C25
1.771,0.333 2.156,0.563 0.385,0.229 1.042,1.76 1.271,1.219 false 0.208,0.156 0.521,0.354 0.313,0.198 10 false *a 0.927,1.781 1.24,1.979 0.313,0.198 10 false +S 4.656,1.656 4.969,1.854 0.313,0.198 10 false A 6.021,1.458 6.417,1.688 0.396,0.229 10 false GND 1.875,0.354 2.188,0.552 0.313,0.198 10 false F6
*a Component with harness connected
(Meter Circuit Plate)
- -


i.

Remove the meter circuit plate with the connector still connected.


ii.

Connect an oscilloscope to terminal F6-19 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F6-19 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265791C29
1.646,0.271 2.063,0.531 0.417,0.26 2.604,1.844 2.406,1.406 false 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.729,0.302 2.042,0.5 0.313,0.198 10 false F31 2.5,1.854 2.813,2.052 0.313,0.198 10 false SPD 4.781,1.729 5.094,1.927 0.313,0.198 10 false A 6.167,1.448 6.594,1.667 0.427,0.219 10 false GND
*a Component with harness connected
(Radio and Display Receiver Assembly)
- -


i.

Remove the radio and display receiver assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal F31-17 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F31-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)

C

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-17 (SPD) - F79-10 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the F6 meter circuit plate connector.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-19 (+S) - F79-7 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the F85 No. 17 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-17 (SPD) - F85-18 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 17 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 17 JUNCTION CONNECTOR)
a.

Disconnect the F6 meter circuit plate connector.


b.

Disconnect the F85 No. 17 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-19 (+S) - F85-16 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 17 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR