Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2015.11–2016.08
RM3210E _56 Audio / Visual / Telematics _047510 AUDIO / VIDEO _0243397 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E336580E04
0.594,2.052 1.813,2.49 1.219,0.438 10 false Stereo Component Amplifier Assembly 0.604,1.885 0.969,2.115 0.365,0.229 10 false F61 5.135,1.875 5.5,2.104 0.365,0.229 10 false F31 5.135,2.042 6.833,2.583 1.698,0.542 10 false Radio and Display Receiver Assembly 5.542,1.021 6,1.229 0.458,0.208 10 false MUT1 5.281,0.927 5.552,1.167 0.271,0.24 10 false 16 1.74,0.917 2.01,1.156 0.271,0.24 10 false 1 1.26,1.021 1.75,1.229 0.49,0.208 10 false MUTE

PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E225824C44
1.49,0.792 1.948,1.073 0.458,0.281 2.396,1.885 2.865,2.385 false 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.594,0.844 1.927,1 0.333,0.156 10 false F61 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F61-1 (MUTE) - Body ground Power switch on (ACC), audio system playing
→ Changing modes
3.5 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the F61 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-16 (MUT1) - F61-1 (MUTE) Always Below 1 Ω
F31-16 (MUT1) or F61-1 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.

Reconnect the F61 stereo component amplifier assembly connector.


b.
E265411C25
1.5,0.5 1.938,0.781 0.438,0.281 1.135,2.552 1,2.063 false 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.594,0.552 1.948,0.76 0.354,0.208 10 false F31 0.969,2.594 1.615,2.854 0.646,0.26 10 false MUT1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F31-16 (MUT1) - Body ground Power switch on (ACC), audio system is playing 3.5 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY