Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD
RM3210E _56 Audio / Visual / Telematics _047510 AUDIO / VIDEO _0243404 RADIO ANTENNA CORD A

AUDIO / VIDEO  RADIO ANTENNA CORD  INSTALLATION  


PROCEDURE

Hide 86101Q 1.INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY

a.

Engage the 2 grommets.


b.

Engage the clamp.


c.

Connect the washer hose.


d.

Connect the connector.


e.

Engage the 3 clamps.


f.

Connect the washer hose.


g.

Connect the connector to install the No. 4 antenna cord sub-assembly.


Hide 67937B 2.INSTALL BACK DOOR SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR>REASSEMBLY


Hide 64790B 3.INSTALL BACK DOOR UPPER TRIM PANEL ASSEMBLY

Hide 86101D 4.INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY

a.

Engage the 6 clamps.


b.

Engage the claw.


c.

Connect the connector to install the No. 3 antenna cord sub-assembly.


Hide 86101R 5.INSTALL NO. 5 ANTENNA CORD SUB-ASSEMBLY

a.

w/ Digital Audio Broadcasting Antenna or Television Antenna:

i.

Engage the clamp.


ii.

Connect the connector to install the No. 5 antenna cord sub-assembly.



Hide 86101J 6.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

HINT:

Butyl tape and adhesive tape are not available as supply parts. If these pieces of tape still have enough adhesion to secure the No. 2 antenna cord sub-assembly to the roof headlining assembly, reuse them. If the adhesive tape and/or the butyl tape is no longer sticky, apply new tape following the procedure below.


a.

Apply new butyl tape.

w/o Digital Audio Broadcasting Antenna or Television Antenna:

E338068C02
5.156,1.458 4.656,1.115 false 5.573,4.396 5.073,4.052 false 0.271,0.344 0.646,0.583 0.375,0.24 12 false *A 0.354,3.51 0.729,3.75 0.375,0.24 12 false *B 5.219,1.438 5.531,1.635 0.313,0.198 10 false *a 5.625,4.375 5.938,4.573 0.313,0.198 10 false *a
*A w/o Sliding Roof *B w/ Sliding Roof
*a Marking - -
V100144

Butyl tape
V100136

Front


w/ Digital Audio Broadcasting Antenna or Television Antenna:

E341906C01
5.156,1.51 4.604,1.135 false 5.479,4.688 4.927,4.313 false 5.208,1.469 5.521,1.667 0.313,0.198 10 false *a 5.5,4.625 5.813,4.823 0.313,0.198 10 false *a 0.333,0.677 0.708,0.917 0.375,0.24 12 false *A 0.333,3.552 0.708,3.792 0.375,0.24 12 false *B
*A w/o Sliding Roof *B w/ Sliding Roof
*a Marking - -
V100144

Butyl tape
V100136

Front


i.

Remove the old butyl tape from the roof headlining assembly.


ii.

Prepare an appropriate amount of new butyl tape.

HINT:

Be careful not to touch the adhesive surface.



iii.

Apply the butyl tape to the roof headlining assembly while aligning the tape with the markings on the roof headlining assembly.


iv.

Peel off the release paper from the butyl tape.



b.

w/o Digital Audio Broadcasting Antenna or Television Antenna:

i.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

E338069C03
1,1.344 1.51,1.271 true 0.99,5.208 1.5,5.135 true 5.573,0.604 6,0.906 true 5.563,4.479 5.99,4.781 true 5.594,2.708 5.802,2.406 true 6.135,1.604 6.135,1.313 false 6.135,5.479 6.135,5.188 false 4.479,6.708 5.063,7.063 true 4.323,2.823 4.906,3.177 true 3.25,2.76 3.25,2.969 false 1.604,5.281 1.604,5.49 false 2.948,6.427 2.948,6.635 false 1.583,1.417 1.583,1.625 false 2.333,6.135 2.646,5.813 true 2.448,2.313 2.76,1.99 true 5.583,6.552 5.792,6.25 true 0.146,0.198 0.521,0.438 0.375,0.24 12 false *A 0.208,4.073 0.583,4.313 0.375,0.24 12 false *B 0.813,1.281 1.125,1.479 0.313,0.198 10 false *a 0.813,5.156 1.125,5.354 0.313,0.198 10 false *a 2.677,5.719 2.99,5.917 0.313,0.198 10 false *c 2.802,1.885 3.115,2.083 0.313,0.198 10 false *c 5.385,0.521 5.698,0.719 0.313,0.198 10 false *b 5.396,4.406 5.708,4.604 0.313,0.198 10 false *b 5.49,2.719 5.698,2.927 0.208,0.208 10 true *d 6.052,1.604 6.365,1.802 0.313,0.198 10 false *g 6.052,5.479 6.365,5.677 0.313,0.198 10 false *g 5.115,7.031 5.427,7.229 0.313,0.198 10 false *e 4.969,3.156 5.281,3.354 0.313,0.198 10 false *e 1.531,1.656 1.844,1.854 0.313,0.198 10 false *f 1.542,5.521 1.854,5.719 0.313,0.198 10 false *f 3.198,3.021 3.51,3.219 0.313,0.198 10 false *h 2.885,6.677 3.198,6.875 0.313,0.198 10 false *h 5.49,6.552 5.698,6.76 0.208,0.208 10 true *d
*A w/o Sliding Roof *B w/ Sliding Roof
*a Marking Tape (A) *b Marking Tape (B)
*c Adhesive Tape (A) *d Adhesive Tape (B)
*e Adhesive Tape (C) *f Protrusion
*g Notch *h Marking
V113146

Adjustment Area
V100136

Front



ii.

Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the marking tape (A) to the adjustment area.

NOTICE:
·

Make sure that there are no gaps between the roof headlining assembly and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.




iii.

Apply the adhesive tape (A) as shown in the illustration.


iv.

Engage the No. 2 antenna cord sub-assembly to the notch of the roof headlining assembly.


v.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the marking on the roof headlining assembly and secure the No. 2 antenna cord sub-assembly with the adhesive tape (B) as shown in the illustration.


vi.

Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the marking tape (B) to the adjustment area.

NOTICE:
·

Make sure that there are no gaps between the roof headlining assembly and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.



HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.



vii.

Apply the adhesive tape (C) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.



c.

w/ Digital Audio Broadcasting Antenna or Television Antenna:

i.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

E341908C01
2.458,4.979 2.958,4.948 true 2.458,1.104 2.958,1.073 true 5.844,0.635 6.219,0.906 true 5.854,4.51 6.229,4.781 true 1.26,2 1.135,1.521 true 5.823,2.688 6.01,2.396 true 4.948,3.021 4.552,2.823 true 3.021,2.073 2.677,2.313 true 2.75,3.229 2.396,3.083 true 2.896,7.083 2.531,6.844 true 5.146,6.948 4.698,6.688 true 5.844,6.552 6.031,6.26 true 2.927,5.896 2.583,6.135 true 6.302,5.438 6.365,5.167 false 6.292,1.583 6.354,1.313 false 3.063,1.469 3.063,1.229 false 3.073,5.333 3.073,5.094 false 3.521,3.094 3.521,2.76 false 3.188,6.75 3.188,6.417 true 2.292,1.021 2.604,1.219 0.313,0.198 10 false *a 5.677,4.438 5.99,4.635 0.313,0.198 10 false *b 2.302,4.885 2.615,5.083 0.313,0.198 10 false *a 5.677,0.563 5.99,0.76 0.313,0.198 10 false *b 1.188,1.99 1.5,2.188 0.313,0.198 10 false *c 5.708,2.677 5.917,2.885 0.208,0.208 10 true *e 3.042,1.969 3.25,2.177 0.208,0.208 10 true *d 2.792,3.156 3,3.365 0.208,0.208 10 true *f 4.99,2.938 5.198,3.146 0.208,0.208 10 true *g 2.938,7.021 3.146,7.229 0.208,0.208 10 false *h 5.74,6.552 5.948,6.76 0.208,0.208 10 true *e 2.958,5.802 3.167,6.01 0.208,0.208 10 true *d 3.021,1.479 3.26,1.688 0.24,0.208 10 false *i 3.031,5.344 3.271,5.552 0.24,0.208 10 false *i 6.25,1.604 6.49,1.813 0.24,0.208 10 false *j 6.25,5.458 6.49,5.667 0.24,0.208 10 false *j 3.125,6.76 3.365,6.969 0.24,0.208 10 false *k 3.448,3.104 3.688,3.313 0.24,0.208 10 false *k 5.177,6.865 5.385,7.073 0.208,0.208 10 true *g 0.208,4.073 0.583,4.313 0.375,0.24 12 false *B 0.208,0.26 0.583,0.5 0.375,0.24 12 false *A
*A w/o Sliding Roof *B w/ Sliding Roof
*a Marking Tape (A) *b Marking Tape (B)
*c Marking Tape (C) *d Adhesive Tape (A)
*e Adhesive Tape (B) *f Adhesive Tape (C)
*g Adhesive Tape (D) *h Adhesive Tape (E)
*i Protrusion *j Notch
*k Marking - -
V100155

Adhesive Tape
V100136

Front
V113146

Adjustment Area - -



ii.

Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the marking tape (A) to each adjustment area.


iii.

Apply the adhesive tape (A) as shown in the illustration.


iv.

Engage the No. 2 antenna cord sub-assembly to the notch of the roof headlining assembly.


v.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the marking on the roof headlining assembly and secure the No. 2 antenna cord sub-assembly with the adhesive tape (B) as shown in the illustration.


vi.

Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the marking tape (B) to the adjustment area.

NOTICE:
·

Make sure that there are no gaps between the roof headlining assembly and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.



HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.



vii.

w/o Sliding Roof:

1.

Align the marking tape (C) on the No. 2 antenna cord sub-assembly with the marking on the roof headlining assembly and secure the No. 2 antenna cord sub-assembly with the adhesive tape (C) as shown in the illustration.



viii.

Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the marking tape (C) to the adjustment area.

NOTICE:
·

Make sure that there are no gaps between the roof headlining assembly and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.



HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.



ix.

Apply the adhesive tape (D) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.


x.

Apply the adhesive tape (E) to secure the No. 2 antenna cord sub-assembly. (The adhesive tape (E) is not necessary when the No. 2 antenna cord sub-assembly is installed to butyl tape applied to the roof headlining assembly.)


xi.

Engage each clamp.



Hide 7.INSTALL ROOF HEADLINING ASSEMBLY

Hide 86101H 8.INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)

a.

w/ Navigation Antenna:

i.

Engage the 6 clamps to install the antenna cord sub-assembly.



Hide 86101 9.INSTALL ANTENNA CORD SUB-ASSEMBLY

a.

for LHD:

i.

Engage the 6 clamps to install the antenna cord sub-assembly.



b.

for RHD:

i.

Engage the 4 clamps to install the antenna cord sub-assembly.



Hide 55463D 10.INSTALL NO. 3 KNEE PROTECTOR BRACKET (for LHD)

Hide 55462C 11.INSTALL NO. 2 KNEE PROTECTOR BRACKET (for LHD)

Hide 55085 12.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 55084E 13.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)

Hide 14.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY