Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 1 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Central gateway ECU (network gateway ECU)

·

Millimeter wave radar sensor assembly

(w/ Toyota Safety Sense)

·

Driving support ECU assembly

(w/ Toyota Safety Sense)

·

Forward recognition camera

(w/ Toyota Safety Sense)

·

Clearance warning ECU assembly

(w/ Simple Intelligent Parking Assist System)

·

Swing grille actuator assembly

(w/ Grille Shutter System)

·

Blind spot monitor sensor LH

(w/ Blind Spot Monitor System)

·

Rear television camera assembly

(w/ Parking Assist Monitor System)

·

No. 1 CAN junction connector

·

No. 7 CAN junction connector

(w/o Occupant Classification System)



WIRING DIAGRAM

C351229E02
0.052,0.063 2.708,0.51 2.656,0.448 12 false w/ Occupant Classification System 0.948,1.438 1.563,1.635 0.615,0.198 10 false CA1H 0.969,1.906 1.583,2.104 0.615,0.198 10 false CA1L 0.948,3.417 1.563,3.615 0.615,0.198 10 false CAXH 0.969,3.896 1.583,4.094 0.615,0.198 10 false CAXL 1.458,3.396 2.073,3.594 0.615,0.198 10 false 9 1.49,1.885 2.104,2.083 0.615,0.198 10 false 8 1.469,1.427 2.083,1.625 0.615,0.198 10 false 23 0.344,1.75 0.958,1.948 0.615,0.198 10 false 120 Ω 1.438,3.885 2.052,4.083 0.615,0.198 10 false 24 3.083,3.885 3.698,4.083 0.615,0.198 10 false 14 3.146,3.396 3.76,3.594 0.615,0.198 10 false 3 3.073,1.896 3.688,2.094 0.615,0.198 10 false 13 3.135,1.427 3.75,1.625 0.615,0.198 10 false 2 4.25,1.427 4.865,1.625 0.615,0.198 10 false 1 4.219,1.875 4.833,2.073 0.615,0.198 10 false 12 5.906,1.875 6.521,2.073 0.615,0.198 10 false 3 5.906,1.396 6.521,1.594 0.615,0.198 10 false 2 5.469,2.469 6.083,2.667 0.615,0.198 10 false A36 5.771,2.469 7.083,3.083 1.313,0.615 10 false Swing Grille Actuator Assembly 6.156,2.021 6.771,2.219 0.615,0.198 10 false CANN 6.167,1.552 6.781,1.75 0.615,0.198 10 false CANP 0.344,3.75 0.958,3.948 0.615,0.198 10 false 120 Ω 2.979,4.365 3.594,4.563 0.615,0.198 10 false F69 3.302,4.365 4.563,4.771 1.26,0.406 10 false No. 1 CAN Junction Connector 0.073,4.354 0.688,4.552 0.615,0.198 10 false F59 0.365,4.354 2.313,4.74 1.948,0.385 10 false Central Gateway ECU (Network Gateway ECU)

C351213E03
0.104,0.094 3.177,0.521 3.073,0.427 12 false w/o Occupant Classification System 0.427,1.229 1.198,1.427 0.771,0.198 10 false 120 Ω 0.438,5.688 1.208,5.885 0.771,0.198 10 false 120 Ω 1.052,0.906 1.823,1.104 0.771,0.198 10 false CA1H 1.083,1.365 1.854,1.563 0.771,0.198 10 false CA1L 1.594,0.885 2.365,1.083 0.771,0.198 10 false 23 3.167,0.875 3.938,1.073 0.771,0.198 10 false 4 1.573,1.365 2.344,1.563 0.771,0.198 10 false 8 3.115,1.354 3.885,1.552 0.771,0.198 10 false 14 4.302,0.875 5.073,1.073 0.771,0.198 10 false 5 4.281,1.354 5.052,1.552 0.771,0.198 10 false 15 5.833,0.865 6.604,1.063 0.771,0.198 10 false 2 5.833,1.344 6.604,1.542 0.771,0.198 10 false 7 6.094,1.01 6.865,1.208 0.771,0.198 10 false CA1P 6.094,1.51 6.865,1.708 0.771,0.198 10 false CA1N 4.313,2.854 5.083,3.052 0.771,0.198 10 false 6 4.281,3.333 5.052,3.531 0.771,0.198 10 false 16 6.073,3.448 6.844,3.646 0.771,0.198 10 false CANL 6.073,2.979 6.844,3.177 0.771,0.198 10 false CANH 5.823,2.844 6.594,3.042 0.771,0.198 10 false 4 5.813,3.333 6.583,3.531 0.771,0.198 10 false 1 5.625,1.938 6.396,2.135 0.771,0.198 10 false M55 5.969,1.938 7.135,2.406 1.167,0.469 10 false Blind Spot Monitor Sensor LH*1 5.396,3.896 6.167,4.094 0.771,0.198 10 false R5 5.667,3.896 7.125,4.354 1.458,0.458 10 false Rear Television Camera Assembly*2 4.313,3.99 5.083,4.188 0.771,0.198 10 false 7 4.292,3.656 5.063,3.854 0.771,0.198 10 false 17 2.938,4.417 3.708,4.615 0.771,0.198 10 false M78 3.292,4.417 4.552,4.802 1.26,0.385 10 false No. 7 CAN Junction Connector 4.313,5.333 5.083,5.531 0.771,0.198 10 false 7 4.281,5.813 5.052,6.01 0.771,0.198 10 false 17 3.188,5.344 3.958,5.542 0.771,0.198 10 false 8 3.135,5.813 3.906,6.01 0.771,0.198 10 false 18 3.271,7.229 4.531,7.615 1.26,0.385 10 false No. 1 CAN Junction Connector 2.927,7.229 3.698,7.427 0.771,0.198 10 false F68 4.271,6.688 5.042,6.885 0.771,0.198 10 false 12 4.313,6.219 5.083,6.417 0.771,0.198 10 false 2 5.833,6.219 6.604,6.417 0.771,0.198 10 false 6 5.844,6.688 6.615,6.885 0.771,0.198 10 false 5 6.083,6.344 6.854,6.542 0.771,0.198 10 false CANP 6.073,6.823 6.844,7.021 0.771,0.198 10 false CANN 5.51,7.271 6.281,7.469 0.771,0.198 10 false A37 5.813,7.271 7.135,7.781 1.323,0.51 10 false Swing Grille Actuator Assembly*3 1.594,5.354 2.365,5.552 0.771,0.198 10 false 9 1.573,5.823 2.344,6.021 0.771,0.198 10 false 24 1.083,5.844 1.854,6.042 0.771,0.198 10 false CAXL 1.052,5.365 1.823,5.563 0.771,0.198 10 false CAXH 0.073,6.292 0.844,6.49 0.771,0.198 10 false F59 0.375,6.292 2.313,6.76 1.938,0.469 10 false Central Gateway ECU (Network Gateway ECU) 0.281,7.719 3.427,8.094 3.146,0.375 10 false *1: w/ Blind Spot Monitor System 0.302,7.99 3.406,8.219 3.104,0.229 10 false *2: w/ Parking Assist Monitor System 0.292,8.26 3.26,8.469 2.969,0.208 10 false *3: w/ Grille Shutter System

C351214E03
0.115,0.073 2.885,0.396 2.771,0.323 12 false w/o Occupant Classification System 5.99,1.177 6.302,1.375 0.313,0.198 10 false R1 5.99,1.688 6.302,1.885 0.313,0.198 10 false R2 5.677,1.583 5.99,1.781 0.313,0.198 10 false 18 5.677,1.052 5.99,1.25 0.313,0.198 10 false 17 4.094,1.042 4.406,1.24 0.313,0.198 10 false 3 4.063,1.573 4.375,1.771 0.313,0.198 10 false 13 5.594,2.063 5.906,2.26 0.313,0.198 10 false F26 5.885,2.063 7.073,2.51 1.188,0.448 10 false Clearance Warning ECU Assembly*2 2.99,3.438 3.302,3.635 0.313,0.198 10 false 6 1.375,3.448 1.688,3.646 0.313,0.198 10 false 10 1.375,3.979 1.688,4.177 0.313,0.198 10 false 11 2.938,3.979 3.25,4.177 0.313,0.198 10 false 16 2.99,1.042 3.302,1.24 0.313,0.198 10 false 4 1.427,1.042 1.74,1.24 0.313,0.198 10 false 5 0.865,1.167 1.406,1.427 0.542,0.26 10 false CA1P 0.854,1.708 1.365,1.958 0.51,0.25 10 false CA1N 1.406,1.583 1.719,1.781 0.313,0.198 10 false 11 2.927,1.583 3.24,1.781 0.313,0.198 10 false 14 0.885,4.104 1.458,4.333 0.573,0.229 10 false CA2L 0.865,3.573 1.365,3.813 0.5,0.24 10 false CA2H 0.115,4.531 0.427,4.729 0.313,0.198 10 false F40 0.417,4.531 1.688,4.938 1.271,0.406 10 false Driving Support ECU Assembly*1 0.146,2.208 0.458,2.406 0.313,0.198 10 false O7 0.406,2.208 1.667,2.76 1.26,0.552 10 false Forward Recognition Camera*1 4.083,3.448 4.396,3.646 0.313,0.198 10 false 5 4.073,3.99 4.385,4.188 0.313,0.198 10 false 15 5.74,3.448 6.052,3.646 0.313,0.198 10 false 3 5.719,3.979 6.031,4.177 0.313,0.198 10 false 2 5.99,3.573 6.521,3.854 0.531,0.281 10 false CA2H 5.99,4.104 6.521,4.354 0.531,0.25 10 false CA2L 5.521,4.531 5.833,4.729 0.313,0.198 10 false A2 5.771,4.531 7.156,5 1.385,0.469 10 false Millimeter Wave Radar Sensor Assembly*1 2.844,4.49 3.156,4.688 0.313,0.198 10 false F68 3.156,4.49 4.427,4.938 1.271,0.448 10 false No. 1 CAN Junction Connector 0.302,5.531 2.583,6 2.281,0.469 10 false *1: w/ Toyota Safety Sense 0.292,5.833 3.406,6.25 3.115,0.417 10 false *2: w/ Simple Intelligent Parking Assist System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 20 seconds. Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 52 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Occupant Classification System A
w/o Occupant Classification System B



A

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

B

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 7 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F69 No. 1 CAN junction connector.


c.
C348627C56
1.438,0.094 1.865,0.354 0.427,0.26 0.688,1.833 0.688,0.5 0.688,0.5 0.885,0.5 true 0.698,2.156 0.698,3.26 0.698,3.26 0.865,3.26 true 0.896,2.146 0.896,3.01 0.896,3.01 1.063,3.01 true 1.104,2.146 1.104,2.781 1.104,2.781 1.271,2.781 true 0.896,1.813 0.896,0.708 0.896,0.708 1.094,0.708 true 1.115,1.792 1.115,0.906 1.115,0.906 1.313,0.906 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.552,0.177 1.865,0.375 0.313,0.198 10 false F69 0.958,0.417 1.552,0.583 0.594,0.167 10 false CANH*b 0.938,3.188 1.531,3.354 0.594,0.167 10 false CANL*b 1.156,0.625 1.75,0.792 0.594,0.167 10 false CANH*c 1.375,0.813 1.969,0.979 0.594,0.167 10 false CANH*c 1.135,2.927 1.729,3.094 0.594,0.167 10 false CANL*c 1.354,2.708 1.948,2.875 0.594,0.167 10 false CANL*c
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Swing Grille Actuator Assembly
*c to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F69-1 (CANH) - F69-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Swing grille actuator assembly
F69-2 (CANH) - F69-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F69-3 (CANH) - F69-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

8.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F59 central gateway ECU (network gateway ECU) connector.


b.
C348627C57
1.438,0.094 1.865,0.354 0.427,0.26 0.896,2.146 0.896,3.01 0.896,3.01 1.063,3.01 true 1.104,2.146 1.104,2.781 1.104,2.781 1.271,2.781 true 0.896,1.813 0.896,0.708 0.896,0.708 1.094,0.708 true 1.115,1.792 1.115,0.906 1.115,0.906 1.313,0.906 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.552,0.177 1.865,0.375 0.313,0.198 10 false F69 1.188,0.635 1.781,0.802 0.594,0.167 10 false CANH*b 1.156,2.938 1.75,3.104 0.594,0.167 10 false CANL*b 1.396,0.833 1.99,1 0.594,0.167 10 false CANH*b 1.375,2.708 1.969,2.875 0.594,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-2 (CANH) - F69-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
F69-3 (CANH) - F69-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M78 No. 7 CAN junction connector.


c.
C348987C17
1.552,0.083 1.969,0.354 0.417,0.271 1.458,1.115 1.458,0.698 1.458,0.698 1.302,0.698 true 1.458,1.323 1.458,1.615 1.458,1.615 1.281,1.615 true 1.885,1.125 1.885,0.5 1.885,0.5 2.052,0.5 true 1.885,1.302 1.885,1.844 1.885,1.844 2.031,1.844 true 1.677,1.125 1.677,0.51 1.677,0.51 1.521,0.51 true 1.677,1.313 1.677,1.823 1.677,1.823 1.51,1.823 true 2.104,1.146 2.104,0.656 2.104,0.656 2.271,0.656 true 2.094,1.302 2.094,1.656 2.094,1.656 2.24,1.656 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.698,0.625 1.313,0.844 0.615,0.219 10 false CANH*b 0.708,1.552 1.271,1.76 0.563,0.208 10 false CANL*b 0.938,0.448 1.542,0.667 0.604,0.219 10 false CANH*c 0.958,1.771 1.573,2.021 0.615,0.25 10 false CANL*c 1.635,0.156 2.063,0.365 0.427,0.208 10 false M78 2.115,1.781 2.729,2.031 0.615,0.25 10 false CANL*d 2.146,0.417 2.75,0.635 0.604,0.219 10 false CANH*d 2.354,0.583 2.958,0.802 0.604,0.219 10 false CANH*e 2.323,1.583 2.938,1.833 0.615,0.25 10 false CANL*e
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Blind Spot Monitor Sensor LH
(w/ Blind Spot Monitor System)
*d to Rear Television Camera Assembly
(w/ Parking Assist Monitor System)
*e to No. 1 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M78-4 (CANH) - M78-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
M78-5 (CANH) - M78-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH*1
M78-6 (CANH) - M78-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Rear television camera assembly*2
M78-7 (CANH) - M78-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction connector


·

*1: w/ Blind Spot Monitor System

·

*2: w/ Parking Assist Monitor System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 1 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

D

8.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
5.CHECK FOR SHORT IN CAN BUS LINES (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F59 central gateway ECU (network gateway ECU) connector.


b.
C348987C03
1.552,0.083 1.969,0.354 0.417,0.271 1.458,1.115 1.458,0.698 1.458,0.698 0.792,0.698 true 1.458,1.323 1.458,1.615 1.458,1.615 0.781,1.615 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.25,0.625 0.865,0.844 0.615,0.219 10 false CANH*b 0.24,1.542 0.802,1.75 0.563,0.208 10 false CANL*b 1.635,0.156 2.063,0.365 0.427,0.208 10 false M78
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M78-4 (CANH) - M78-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M78 No. 7 CAN junction connector.


b.

Disconnect the F68 No. 1 CAN junction connector.


c.
C348987C18
0.094,1.042 0.51,1.281 0.417,0.24 1.042,1.125 1.042,0.583 1.042,0.583 0.906,0.583 true 1.042,1.313 1.042,1.719 1.042,1.719 0.896,1.719 true 1.25,1.313 1.25,1.885 1.25,1.885 1.104,1.885 true 1.25,1.125 1.25,0.406 1.25,0.406 1.115,0.406 true 1.458,1.135 1.458,0.25 1.458,0.25 1.323,0.25 true 1.458,1.313 1.458,2.063 1.458,2.063 1.313,2.063 true 1.667,1.125 1.667,0.229 1.667,0.229 1.833,0.229 true 1.885,1.125 1.885,0.385 1.885,0.385 2.052,0.385 true 2.104,1.125 2.104,0.552 2.104,0.552 2.323,0.552 true 2.302,1.125 2.302,0.729 2.302,0.729 2.615,0.729 true 1.677,1.302 1.677,2.063 1.677,2.063 1.844,2.063 true 1.896,1.302 1.896,1.906 1.896,1.906 2.042,1.906 true 2.104,1.302 2.104,1.74 2.104,1.74 2.26,1.74 true 2.313,1.313 2.313,1.583 2.313,1.583 2.469,1.583 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.344,0.521 0.958,0.74 0.615,0.219 10 false CANH*b 0.323,1.635 0.885,1.844 0.563,0.208 10 false CANL*b 0.542,0.333 1.146,0.552 0.604,0.219 10 false CANH*c 0.542,1.802 1.156,2.052 0.615,0.25 10 false CANL*c 0.188,1.104 0.615,1.313 0.427,0.208 10 false F68 0.74,1.99 1.354,2.167 0.615,0.177 10 false CANL*d 0.76,0.177 1.365,0.396 0.604,0.219 10 false CANH*d 1.917,0.146 2.521,0.365 0.604,0.219 10 false CANH*e 1.917,1.99 2.531,2.146 0.615,0.156 10 false CANL*e 2.135,0.313 2.74,0.531 0.604,0.219 10 false CANH*f 2.406,0.479 3.01,0.698 0.604,0.219 10 false CANH*g 2.698,0.646 3.302,0.865 0.604,0.219 10 false CANH*h 2.354,1.667 2.969,1.823 0.615,0.156 10 false CANL*g 2.552,1.51 3.167,1.667 0.615,0.156 10 false CANL*h 2.146,1.833 2.76,1.99 0.615,0.156 10 false CANL*f
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Swing Grille Actuator Assembly
(w/ Grille Shutter System)
*c to Clearance Warning ECU Assembly
(w/ Simple Intelligent Parking Assist System)
*d to Forward Recognition Camera
(w/ Toyota Safety Sense)
*e to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*f to Driving Support ECU Assembly
(w/ Toyota Safety Sense)
*g to No. 7 CAN Junction Connector
*h to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F68-2 (CANH) - F68-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Swing grille actuator assembly*1
F68-3 (CANH) - F68-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance warning ECU assembly*2
F68-4 (CANH) - F68-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward recognition camera*3
F68-5 (CANH) - F68-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*3
F68-6 (CANH) - F68-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Driving support ECU assembly*3
F68-7 (CANH) - F68-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 7 CAN junction connector
F68-8 (CANH) - F68-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)


·

*1: w/ Grille Shutter System

·

*2: w/ Simple Intelligent Parking Assist System

·

*3: w/ Toyota Safety Sense



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 7 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

7.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 CAN JUNCTION CONNECTOR)

D

8.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
7.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F59 central gateway ECU (network gateway ECU) connector.


b.
C348987C19
1.563,0.24 1.979,0.479 0.417,0.24 2.302,1.135 2.302,0.667 2.302,0.667 2.438,0.667 true 2.302,1.302 2.302,1.635 2.302,1.635 2.438,1.635 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 2.521,1.563 3.083,1.771 0.563,0.208 10 false CANL*b 1.667,0.281 2.094,0.49 0.427,0.208 10 false F68 2.5,0.594 3.115,0.813 0.615,0.219 10 false CANH*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F68-8 (CANH) - F68-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

8.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C347970C15
1.521,0.188 1.885,0.417 0.365,0.229 1.042,0.479 1.229,0.479 1.229,0.479 1.229,0.969 true 0.979,1.927 1.177,1.927 1.177,1.927 1.177,1.135 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.573,1.865 1.198,2.021 0.625,0.156 10 false CA1H 0.656,0.427 1.167,0.583 0.51,0.156 10 false CA1L 1.604,0.229 1.958,0.396 0.354,0.167 10 false F59
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F59-23 (CA1H) - F59-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR