Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2015.11–2016.08
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR (w/o Occupant Classification System)


a.

Check the No. 1 CAN junction connector.

i.

Connection diagram

C349815C12
1.604,1.281 2.01,1.563 0.406,0.281 2.75,1.344 2.75,0.583 2.75,0.583 2.604,0.583 true 2.99,1.354 2.99,0.385 2.99,0.385 2.833,0.385 true 4.125,2.24 3.948,2.24 3.948,2.24 3.948,1.573 true 3.229,1.344 3.229,0.188 3.229,0.188 3.073,0.188 true 3.458,1.344 3.458,0.188 3.458,0.188 3.635,0.188 true 3.708,1.344 3.708,0.375 3.708,0.375 3.885,0.375 true 3.958,1.344 3.958,0.583 3.958,0.583 4.146,0.583 true 4.188,1.333 4.188,0.771 4.188,0.771 4.365,0.771 true 2.802,2.448 2.979,2.448 2.979,2.448 2.979,1.583 true 3.646,2.635 3.469,2.635 3.469,2.635 3.469,1.573 true 3.042,2.635 3.219,2.635 3.219,2.635 3.219,1.573 true 3.906,2.438 3.708,2.438 3.708,2.438 3.708,1.573 true 2.573,2.24 2.74,2.24 2.74,2.24 2.74,1.573 true 4.365,2 4.198,2 4.198,2 4.198,1.573 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.021,0.51 2.677,0.708 0.656,0.198 10 false CANH*b 2,2.167 2.656,2.365 0.656,0.198 10 false CANL*b 2.24,2.365 2.896,2.563 0.656,0.198 10 false CANL*c 2.26,0.302 2.917,0.5 0.656,0.198 10 false CANH*c 2.5,0.115 3.156,0.313 0.656,0.198 10 false CANH*d 1.698,1.365 2.354,1.563 0.656,0.198 10 false F68 3.708,0.115 4.365,0.313 0.656,0.198 10 false CANH*e 3.958,0.302 4.615,0.5 0.656,0.198 10 false CANH*f 4.448,0.708 5.104,0.906 0.656,0.198 10 false CANH*h 4.219,0.531 4.875,0.729 0.656,0.198 10 false CANH*g 2.5,2.552 3.156,2.75 0.656,0.198 10 false CANL*d 3.719,2.563 4.375,2.76 0.656,0.198 10 false CANL*e 3.969,2.354 4.625,2.552 0.656,0.198 10 false CANL*f 4.448,1.948 5.104,2.146 0.656,0.198 10 false CANL*h 4.198,2.167 4.854,2.365 0.656,0.198 10 false CANL*g
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Swing Grille Actuator Assembly
(w/ Grille Shutter System)
*c to Clearance Warning ECU Assembly
(w/ Simple Intelligent Parking Assist System)
*d to Forward Recognition Camera
(w/ Toyota Safety Sense)
*e to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*f to Driving Support ECU Assembly
(w/ Toyota Safety Sense)
*g to No. 7 CAN Junction Connector *h to Central Gateway ECU (Network Gateway ECU)



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F68-2 (CANH) B Swing grille actuator assembly*1
(for Bus 1)
F68-12 (CANL) W
F68-3 (CANH) LG Clearance warning ECU assembly*2
(for Bus 1)
F68-13 (CANL) W
F68-4 (CANH) R Forward recognition camera*3
(for Bus 1)
F68-14 (CANL) W
F68-5 (CANH) BE Millimeter wave radar sensor assembly*3
(for Bus 1)
F68-15 (CANL) W
F68-6 (CANH) G Driving support ECU assembly*3
(for Bus 1)
F68-16 (CANL) W
F68-7 (CANH) BE No. 7 CAN junction connector
(for Bus 1)
F68-17 (CANL) W
F68-8 (CANH) SB Central gateway ECU (network gateway ECU)
(for Bus 1)
F68-18 (CANL) W

·

*1: w/ Grille Shutter System

·

*2: w/ Simple Intelligent Parking Assist System

·

*3: w/ Toyota Safety Sense





NO. 1 CAN JUNCTION CONNECTOR (w/ Occupant Classification System)


a.

Check the No. 1 CAN junction connector.

i.

Connection diagram

C349816C01
1.563,1.292 1.979,1.594 0.417,0.302 2.917,1.427 2.917,0.302 2.917,0.302 2.688,0.302 true 2.76,1.427 2.76,0.635 2.76,0.635 2.531,0.635 true 3.094,1.427 3.094,0.302 3.094,0.302 3.302,0.302 true 2.76,1.708 2.76,2.125 2.76,2.125 2.531,2.125 true 2.917,1.708 2.917,2.427 2.917,2.427 2.688,2.427 true 3.094,1.708 3.094,2.427 3.094,2.427 3.313,2.427 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.969,0.573 2.583,0.781 0.615,0.208 10 false CANH*b 1.99,2.063 2.604,2.271 0.615,0.208 10 false CANL*b 2.125,0.24 2.74,0.448 0.615,0.208 10 false CANH*c 2.125,2.365 2.74,2.573 0.615,0.208 10 false CANL*c 1.667,1.385 2.177,1.615 0.51,0.229 10 false F69 3.396,0.25 4.01,0.458 0.615,0.208 10 false CANH*c 3.385,2.365 4,2.573 0.615,0.208 10 false CANL*c
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Swing Grille Actuator Assembly
*c to Central Gateway ECU (Network Gateway ECU) - -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F69-1 (CANH) B Swing grille actuator assembly
(for Bus 1)
F69-12 (CANL) W
F69-2 (CANH) BE Central gateway ECU (network gateway ECU)
(for Bus 1)
F69-13 (CANL) W
F69-3 (CANH) SB Central gateway ECU (network gateway ECU)
(for Bus 1)
F69-14 (CANL) W




NO. 2 CAN JUNCTION CONNECTOR


a.

Check the No. 2 CAN junction connector.

i.

Connection diagram

C349816C24
1.563,1.292 1.979,1.594 0.417,0.302 2.917,1.427 2.917,0.625 2.917,0.625 2.729,0.625 true 2.75,1.427 2.75,0.781 2.75,0.781 2.542,0.781 true 3.083,1.438 3.083,0.479 3.083,0.479 2.885,0.479 true 2.76,1.708 2.76,1.99 2.76,1.99 2.531,1.99 true 2.917,1.719 2.917,2.135 2.917,2.135 2.688,2.135 true 3.094,1.719 3.094,2.333 3.094,2.333 2.885,2.333 true 3.26,1.719 3.26,2.5 3.26,2.5 3.052,2.5 true 3.25,1.417 3.25,0.302 3.25,0.302 3.063,0.302 true 3.76,1.438 3.76,0.135 3.76,0.135 3.938,0.135 true 3.427,1.719 3.427,2.656 3.427,2.656 3.229,2.656 true 3.417,1.417 3.417,0.135 3.417,0.135 3.24,0.135 true 3.927,1.417 3.927,0.302 3.927,0.302 4.115,0.302 true 4.094,1.417 4.094,0.458 4.094,0.458 4.26,0.458 true 4.26,1.427 4.26,0.625 4.26,0.625 4.438,0.625 true 4.438,1.417 4.438,0.792 4.438,0.792 4.646,0.792 true 3.771,1.719 3.771,2.656 3.771,2.656 3.979,2.656 true 3.938,1.719 3.938,2.5 3.938,2.5 4.156,2.5 true 4.094,1.719 4.094,2.333 4.094,2.333 4.333,2.333 true 4.26,1.729 4.26,2.146 4.26,2.146 4.51,2.146 true 4.427,1.708 4.427,1.99 4.427,1.99 4.74,1.99 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.979,0.729 2.594,0.938 0.615,0.208 10 false CANH*b 1.99,1.917 2.604,2.125 0.615,0.208 10 false CANL*b 2.156,0.563 2.771,0.771 0.615,0.208 10 false CANH*c 2.156,2.083 2.771,2.292 0.615,0.208 10 false CANL*c 1.667,1.385 2.177,1.615 0.51,0.229 10 false F70 2.323,0.406 2.938,0.615 0.615,0.208 10 false CANH*d 2.333,2.26 2.948,2.469 0.615,0.208 10 false CANL*d 4.26,2.438 4.885,2.604 0.625,0.167 10 false CANL*h 4.438,2.26 5.052,2.469 0.615,0.208 10 false CANL*f 2.49,0.24 3.198,0.448 0.708,0.208 10 false CANH*e 4.01,0.063 4.625,0.271 0.615,0.208 10 false CANH*g 4.177,0.229 4.792,0.438 0.615,0.208 10 false CANH*h 4.333,0.385 4.948,0.594 0.615,0.208 10 false CANH*f 4.719,0.729 5.333,0.938 0.615,0.208 10 false CANH*j 2.698,0.073 3.313,0.281 0.615,0.208 10 false CANH*f 2.5,2.427 3.167,2.635 0.667,0.208 10 false CANL*e 4.083,2.594 4.698,2.76 0.615,0.167 10 false CANL*g 4.823,1.917 5.438,2.125 0.615,0.208 10 false CANL*j 2.677,2.604 3.292,2.781 0.615,0.177 10 false CANL*f 4.604,2.073 5.219,2.24 0.615,0.167 10 false CANL*i 4.5,0.552 5.115,0.76 0.615,0.208 10 false CANH*i
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Hybrid Vehicle Control ECU *d to Inverter with Converter Assembly
*e to ECM *f to Brake Booster with Master Cylinder Assembly
*g to No. 5 CAN Junction Connector *h to Airbag ECU Assembly
*i to Steering Sensor *j to Power Steering ECU Assembly



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F70-1 (CANH) LG Central gateway ECU (network gateway ECU)
(for Bus 2)
F70-12 (CANL) W
F70-2 (CANH) L Hybrid vehicle control ECU
(for Bus 2)
F70-13 (CANL) W
F70-3 (CANH) GR Inverter with converter assembly
(for Bus 2)
F70-14 (CANL) W
F70-4 (CANH) B ECM
(for Bus 2)
F70-15 (CANL) W
F70-5 (CANH) P Brake booster with master cylinder assembly
(for Bus 2)
F70-16 (CANL) W
F70-7 (CANH) G No. 5 CAN junction connector
(for Bus 4)
F70-18 (CANL) W
F70-8 (CANH) R Airbag ECU assembly
(for Bus 4)
F70-19 (CANL) W
F70-9 (CANH) SB Brake booster with master cylinder assembly
(for Bus 4)
F70-20 (CANL) W
F70-10 (CANH) BE Steering sensor
(for Bus 4)
F70-21 (CANL) W
F70-11 (CANH) V Power steering ECU assembly
(for Bus 4)
F70-22 (CANL) W




NO. 3 CAN JUNCTION CONNECTOR


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C349816C03
1.563,1.292 1.979,1.594 0.417,0.302 2.917,1.427 2.917,0.625 2.917,0.625 2.729,0.625 true 2.75,1.427 2.75,0.781 2.75,0.781 2.542,0.781 true 3.083,1.438 3.083,0.479 3.083,0.479 2.885,0.479 true 2.76,1.708 2.76,1.99 2.76,1.99 2.531,1.99 true 2.917,1.719 2.917,2.135 2.917,2.135 2.688,2.135 true 3.094,1.719 3.094,2.333 3.094,2.333 2.885,2.333 true 3.26,1.719 3.26,2.5 3.26,2.5 3.052,2.5 true 3.25,1.417 3.25,0.302 3.25,0.302 3.063,0.302 true 3.594,1.427 3.594,0.271 3.594,0.271 3.771,0.271 true 3.427,1.719 3.427,2.656 3.427,2.656 3.229,2.656 true 3.417,1.417 3.417,0.135 3.417,0.135 3.24,0.135 true 3.76,1.427 3.76,0.594 3.76,0.594 3.948,0.594 true 3.604,1.719 3.604,2.458 3.604,2.458 3.813,2.458 true 3.76,1.719 3.76,2.208 3.76,2.208 3.979,2.208 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.979,0.729 2.594,0.938 0.615,0.208 10 false CANH*b 1.99,1.917 2.604,2.125 0.615,0.208 10 false CANL*b 2.156,0.563 2.771,0.771 0.615,0.208 10 false CANH*c 2.156,2.083 2.771,2.292 0.615,0.208 10 false CANL*c 1.667,1.385 2.177,1.615 0.51,0.229 10 false F71 2.323,0.406 2.938,0.615 0.615,0.208 10 false CANH*d 2.333,2.26 2.948,2.469 0.615,0.208 10 false CANL*d 4.063,2.156 4.688,2.323 0.625,0.167 10 false CANL*h 2.708,2.604 3.323,2.76 0.615,0.156 10 false CANL*f 2.521,0.24 3.229,0.448 0.708,0.208 10 false CANH*e 3.844,0.229 4.458,0.438 0.615,0.208 10 false CANH*g 4.031,0.542 4.646,0.75 0.615,0.208 10 false CANH*h 2.719,0.073 3.333,0.281 0.615,0.208 10 false CANH*f 2.479,2.438 3.146,2.646 0.667,0.208 10 false CANL*e 3.896,2.406 4.51,2.573 0.615,0.167 10 false CANL*g
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Meter Circuit Plate
*c to Main Body ECU (Multiplex Network Body ECU) *d to No. 1 Headlight ECU Sub-assembly LH
*e to Air Conditioning Amplifier Assembly *f to Certification ECU (Smart Key ECU Assembly)
*g to Central Gateway ECU (Network Gateway ECU) *h to Combination Meter Mirror ECU
(w/ Headup Display System)



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F71-1 (CANH) V Meter circuit plate
(for Bus 5)
F71-12 (CANL) W
F71-2 (CANH) SB Main body ECU (multiplex network body ECU)
(for Bus 5)
F71-13 (CANL) W
F71-3 (CANH) L No. 1 headlight ECU sub-assembly LH
(for Bus 5)
F71-14 (CANL) W
F71-4 (CANH) BE Air conditioning amplifier assembly
(for Bus 5)
F71-15 (CANL) W
F71-5 (CANH) R Certification ECU (smart key ECU assembly)
(for Bus 5)
F71-16 (CANL) W
F71-6 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 5)
F71-17 (CANL) W
F71-7 (CANH) P Combination meter mirror ECU*
(for Bus 5)
F71-18 (CANL) W

*: w/ Headup Display System





NO. 4 CAN JUNCTION CONNECTOR


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C349816C29
1.563,1.292 1.979,1.594 0.417,0.302 2.75,1.427 2.75,0.781 2.75,0.781 2.542,0.781 true 3.083,1.438 3.083,0.479 3.083,0.479 2.885,0.479 true 2.76,1.708 2.76,1.99 2.76,1.99 2.531,1.99 true 3.094,1.719 3.094,2.333 3.094,2.333 2.885,2.333 true 3.26,1.719 3.26,2.5 3.26,2.5 3.052,2.5 true 3.25,1.417 3.25,0.302 3.25,0.302 3.063,0.302 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.979,0.729 2.594,0.938 0.615,0.208 10 false CANH*b 1.99,1.917 2.604,2.125 0.615,0.208 10 false CANL*b 1.667,1.385 2.177,1.615 0.51,0.229 10 false F72 2.323,0.406 2.938,0.615 0.615,0.208 10 false CANH*c 2.333,2.26 2.948,2.469 0.615,0.208 10 false CANL*c 2.521,0.24 3.135,0.448 0.615,0.208 10 false CANH*c 2.51,2.438 3.125,2.646 0.615,0.208 10 false CANL*c
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b
·

to Navigation Receiver Assembly

(for Navigation Receiver Type)

·

to Radio and Display Receiver Assembly

(for Radio and Display Type)


*c to Central Gateway ECU (Network Gateway ECU) - -



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F72-1 (CANH) L
·

to Navigation Receiver Assembly*1

·

to Radio and Display Receiver Assembly*2


(for Bus 3)
F72-12 (CANL) W
F72-3 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 3)
F72-14 (CANL) W
F72-4 (CANH) V Central gateway ECU (network gateway ECU)
(for Bus 3)
F72-15 (CANL) W

·

*1: for Navigation Receiver Type

·

*2: for Radio and Display Type





NO. 5 CAN JUNCTION CONNECTOR


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C349816C16
1.563,1.292 1.979,1.594 0.417,0.302 2.917,1.427 2.917,0.625 2.917,0.625 2.729,0.625 true 2.75,1.427 2.75,0.781 2.75,0.781 2.542,0.781 true 3.083,1.438 3.083,0.479 3.083,0.479 2.885,0.479 true 2.76,1.708 2.76,1.99 2.76,1.99 2.531,1.99 true 2.917,1.719 2.917,2.135 2.917,2.135 2.688,2.135 true 3.094,1.719 3.094,2.333 3.094,2.333 2.885,2.333 true 3.26,1.719 3.26,2.5 3.26,2.5 3.052,2.5 true 3.25,1.427 3.25,0.313 3.25,0.313 3.063,0.313 true 3.427,1.427 3.427,0.313 3.427,0.313 3.583,0.313 true 3.427,1.719 3.427,2.5 3.427,2.5 3.583,2.5 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.979,0.729 2.594,0.938 0.615,0.208 10 false CANH*b 1.99,1.917 2.604,2.125 0.615,0.208 10 false CANL*b 2.156,0.563 2.771,0.771 0.615,0.208 10 false CANH*c 2.156,2.083 2.771,2.292 0.615,0.208 10 false CANL*c 1.667,1.385 2.177,1.615 0.51,0.229 10 false F73 2.323,0.406 2.938,0.615 0.615,0.208 10 false CANH*d 2.333,2.26 2.948,2.469 0.615,0.208 10 false CANL*d 2.469,0.25 3.177,0.458 0.708,0.208 10 false CANH*e 2.51,2.438 3.177,2.646 0.667,0.208 10 false CANL*e 3.656,2.427 4.323,2.635 0.667,0.208 10 false CANL*f 3.667,0.24 4.375,0.448 0.708,0.208 10 false CANH*f
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to ECM
*e to Hybrid Vehicle Control ECU *f to Occupant Detection ECU
(w/ Occupant Classification System)



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F73-1 (CANH) G No. 2 CAN junction connector
(for Bus 4)
F73-12 (CANL) W
F73-2 (CANH) LG Central gateway ECU (network gateway ECU)
(for Bus 4)
F73-13 (CANL) W
F73-3 (CANH) SB ECM
(for Bus 4)
F73-14 (CANL) W
F73-4 (CANH) G Hybrid vehicle control ECU
(for Bus 4)
F73-15 (CANL) W
F73-5 (CANH) L Occupant detection ECU*
(for Bus 4)
F73-16 (CANL) W

*: w/ Occupant Classification System





NO. 7 CAN JUNCTION CONNECTOR (w/o Occupant Classification System)


a.

Check the No. 7 CAN junction connector.

i.

Connection diagram

C349815C04
1.531,1.292 1.958,1.563 0.427,0.271 3.063,2.115 3.219,2.115 3.219,2.115 3.219,1.563 true 3.469,1.344 3.469,0.375 3.469,0.375 3.333,0.375 true 3.229,1.344 3.229,0.594 3.229,0.594 3.083,0.594 true 3.281,2.385 3.458,2.385 3.458,2.385 3.458,1.563 true 3.948,1.354 3.948,0.604 3.948,0.604 4.115,0.604 true 4.125,2.115 3.958,2.115 3.958,2.115 3.958,1.563 true 3.719,1.344 3.719,0.385 3.719,0.385 3.885,0.385 true 3.875,2.385 3.719,2.385 3.719,2.385 3.719,1.563 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 2.531,0.531 3.188,0.729 0.656,0.198 10 false CANH*b 2.521,2.063 3.177,2.26 0.656,0.198 10 false CANL*b 2.729,2.313 3.385,2.51 0.656,0.198 10 false CANL*c 2.771,0.292 3.427,0.49 0.656,0.198 10 false CANH*c 4.208,0.542 4.865,0.74 0.656,0.198 10 false CANH*e 3.948,2.302 4.604,2.5 0.656,0.198 10 false CANL*d 1.625,1.375 2.281,1.573 0.656,0.198 10 false M78 3.958,0.302 4.615,0.5 0.656,0.198 10 false CANH*d 4.198,2.031 4.854,2.229 0.656,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Blind Spot Monitor Sensor LH
(w/ Blind Spot Monitor System)
*d to Rear Television Camera Assembly
(w/ Parking Assist Monitor System)
*e to No. 1 CAN Junction Connector - -



ii.

Check the connection diagram of the components which are connected to the No. 7 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M78-4 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
M78-14 (CANL) W
M78-5 (CANH) B Blind spot monitor sensor LH*1
(for Bus 1)
M78-15 (CANL) W
M78-6 (CANH) LG Rear television camera assembly*2
(for Bus 1)
M78-16 (CANL) W
M78-7 (CANH) BE No. 1 CAN junction connector
(for Bus 1)
M78-17 (CANL) W

·

*1: w/ Blind Spot Monitor System

·

*2: w/ Parking Assist Monitor System





DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C349818C01
1.625,1.313 2.042,1.583 0.417,0.271 3.865,1.125 3.865,0.51 3.865,0.51 4.052,0.51 true 3.51,1.125 3.51,0.51 3.51,0.51 3.313,0.51 true 4.417,2.24 4.229,2.24 4.229,2.24 4.229,1.708 true 3.667,2.24 3.865,2.24 3.865,2.24 3.865,1.708 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 4.156,0.458 4.792,0.688 0.635,0.229 10 false CANH 3.26,2.198 3.896,2.427 0.635,0.229 10 false CANL 3.042,0.469 3.677,0.698 0.635,0.229 10 false CG 4.51,2.177 5.146,2.406 0.635,0.229 10 false BAT 1.729,1.396 2.365,1.625 0.635,0.229 10 false F29
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F29-6 (CANH) - F29-14 (CANL) V - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F29-6 (CANH) - F29-4 (CG) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F29-14 (CANL) - F29-4 (CG) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F29-6 (CANH) - F29-16 (BAT) V - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F29-14 (CANL) - F29-16 (BAT) P - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C349819C01
1.083,1.281 1.5,1.552 0.417,0.271 3.615,2.51 3.448,2.51 3.448,2.51 3.448,1.427 true 3.552,2.667 3.365,2.667 3.365,2.667 3.365,1.427 true 2.99,1.302 2.99,0.771 2.99,0.771 2.865,0.771 true 3.24,1.292 3.24,0.26 3.24,0.26 3.125,0.26 true 2.885,2.24 3.031,2.24 3.031,2.24 3.031,1.438 true 3.542,1.375 3.542,0.51 3.542,0.51 3.698,0.51 true 2.792,1.979 2.948,1.979 2.948,1.979 2.948,1.438 true 3.115,2.615 3.281,2.615 3.281,2.615 3.281,1.427 true 3.042,2.438 3.198,2.438 3.198,2.438 3.198,1.438 true 3.156,1.302 3.156,0.438 3.156,0.438 3.01,0.438 true 3.073,1.302 3.073,0.594 3.073,0.594 2.917,0.594 true 3.625,1.385 3.625,0.667 3.625,0.667 3.781,0.667 true 3.885,2.354 3.719,2.354 3.719,2.354 3.719,1.438 true 3.958,2.188 3.792,2.188 3.792,2.188 3.792,1.427 true 4.042,2 3.875,2 3.875,2 3.875,1.427 true 3.917,1.292 3.917,0.854 3.917,0.854 4.073,0.854 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 2.469,2.177 2.958,2.354 0.49,0.177 10 false CA1H 2.542,0.542 3.094,0.76 0.552,0.219 10 false CA1L 2.646,0.385 3.198,0.604 0.552,0.219 10 false CA2L 2.656,2.375 3.146,2.552 0.49,0.177 10 false CA2H 2.75,0.198 3.24,0.375 0.49,0.177 10 false CA3H 2.75,2.563 3.302,2.781 0.552,0.219 10 false CA3L 2.458,0.719 2.948,0.896 0.49,0.177 10 false CAXH 2.417,1.927 2.906,2.104 0.49,0.177 10 false CAXL 3.688,2.448 4.177,2.625 0.49,0.177 10 false CAYH 3.625,2.604 4.115,2.781 0.49,0.177 10 false CAYL 3.771,0.448 4.26,0.625 0.49,0.177 10 false CA4H 4.135,0.792 4.688,1.01 0.552,0.219 10 false CA6L 4.031,2.125 4.521,2.302 0.49,0.177 10 false CA5H 3.969,2.292 4.521,2.51 0.552,0.219 10 false CA5L 1.188,1.354 1.635,1.615 0.448,0.26 10 false F59 4.115,1.938 4.604,2.115 0.49,0.177 10 false CA6H 3.854,0.604 4.406,0.823 0.552,0.219 10 false CA4L
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F59 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C349820C02
1.094,1.708 1.5,1.979 0.406,0.271 4.573,1.74 4.573,1.146 4.573,1.146 4.729,1.146 true 4.427,1.74 4.427,0.917 4.427,0.917 4.583,0.917 true 4.271,1.74 4.271,0.698 4.271,0.698 4.427,0.698 true 4.125,1.74 4.125,0.458 4.125,0.458 4.281,0.458 true 4.646,1.99 4.646,2.573 4.646,2.573 4.802,2.573 true 4.208,1.979 4.208,3.021 4.208,3.021 4.365,3.021 true 4.052,1.99 4.052,3.281 4.052,3.281 4.208,3.281 true 4.51,1.99 4.51,2.813 4.51,2.813 4.667,2.813 true 3.906,1.99 3.906,3.448 3.906,3.448 3.74,3.448 true 3.76,1.979 3.76,3.271 3.76,3.271 3.604,3.271 true 3.604,1.885 3.604,0.458 3.604,0.458 3.448,0.458 true 3.458,1.885 3.458,0.646 3.458,0.646 3.302,0.646 true 3.313,1.99 3.313,3.052 3.313,3.052 3.156,3.052 true 3.156,1.99 3.156,2.875 3.156,2.875 3,2.875 true 2.938,1.75 2.938,0.948 2.938,0.948 2.781,0.948 true 3.01,1.969 3.01,2.604 3.01,2.604 2.854,2.604 true 2.333,1.771 2.333,1.167 2.333,1.167 2.177,1.167 true 4.781,1.802 5.229,1.802 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.198,1.781 1.573,1.99 0.375,0.208 10 false F59 4.74,2.75 5.698,3.031 0.958,0.281 10 false CA1H 4.667,0.854 5.625,1.135 0.958,0.281 10 false CA1L 4.458,2.958 5.417,3.24 0.958,0.281 10 false CA2H 4.385,0.406 5.344,0.688 0.958,0.281 10 false CA3H 3.031,0.396 3.99,0.677 0.958,0.281 10 false CA4H 2.594,2.823 3.552,3.104 0.958,0.281 10 false CA5H 4.833,1.083 5.792,1.365 0.958,0.281 10 false CAXH 3.177,3.219 4.135,3.5 0.958,0.281 10 false CAYH 4.51,0.646 5.469,0.927 0.958,0.281 10 false CA2L 4.292,3.219 5.25,3.5 0.958,0.281 10 false CA3L 2.906,0.594 3.865,0.875 0.958,0.281 10 false CA4L 2.792,3 3.75,3.281 0.958,0.281 10 false CA5L 4.875,2.5 5.833,2.781 0.958,0.281 10 false CAXL 3.365,3.396 4.323,3.677 0.958,0.281 10 false CAYL 2.458,2.542 3.417,2.823 0.958,0.281 10 false CA6H 2.396,0.896 3.354,1.177 0.958,0.281 10 false CA6L 1.771,1.104 2.729,1.385 0.958,0.281 10 false BATT 5.302,1.74 5.865,1.99 0.563,0.25 10 false GND
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Diagnosis Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F59-14 (CA6H) - F59-5 (CA6L) V - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
F59-14 (CA6H) - F59-10 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-5 (CA6L) - F59-10 (GND) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-14 (CA6H) - F59-1 (BATT) V - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F59-5 (CA6L) - F59-1 (BATT) P - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F59-23 (CA1H) - F59-9 (CAXH) P - SB HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F59-8 (CA1L) - F59-24 (CAXL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F59-23 (CA1H) - F59-10 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-8 (CA1L) - F59-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-23 (CA1H) - F59-1 (BATT) P - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F59-8 (CA1L) - F59-1 (BATT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F59-18 (CA4H) - F59-17 (CA4L) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F59-18 (CA4H) - F59-10 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-17 (CA4L) - F59-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-18 (CA4H) - F59-1 (BATT) LG - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F59-17 (CA4L) - F59-1 (BATT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F59-6 (CA3H) - F59-19 (CAYH) G - V HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F59-21 (CA3L) - F59-20 (CAYL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F59-6 (CA3H) - F59-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-21 (CA3L) - F59-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-6 (CA3H) - F59-1 (BATT) G - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F59-21 (CA3L) - F59-1 (BATT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F59-22 (CA2H) - F59-7 (CA2L) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F59-22 (CA2H) - F59-10 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-7 (CA2L) - F59-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-22 (CA2H) - F59-1 (BATT) LG - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F59-7 (CA2L) - F59-1 (BATT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F59-15 (CA5H) - F59-16 (CA5L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F59-15 (CA5H) - F59-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-16 (CA5L) - F59-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-15 (CA5H) - F59-1 (BATT) B - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F59-16 (CA5L) - F59-1 (BATT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




STEERING SENSOR


C349821C01
4.385,0.406 4.802,0.667 0.417,0.26 4.875,2.26 4.729,2.26 4.729,2.26 4.729,1.667 true 4.479,2.26 4.625,2.26 4.625,2.26 4.625,1.667 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 4.49,0.479 4.948,0.677 0.458,0.198 10 false F55 4.948,2.208 5.531,2.458 0.583,0.25 10 false CANL 4.063,2.208 4.646,2.458 0.583,0.25 10 false CANH
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F55 steering sensor connector.


c.
C349822C04
1.406,0.125 1.833,0.417 0.427,0.292 1.729,1.385 1.719,0.521 1.719,0.521 1.896,0.521 true 1.542,1.375 1.542,0.521 1.542,0.521 1.375,0.521 true 2.104,1.438 2.427,1.438 true 1,1.438 1.323,1.438 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.969,0.448 2.594,0.708 0.625,0.26 10 false CANH 0.969,0.448 1.594,0.708 0.625,0.26 10 false CANL 1.49,0.188 2.115,0.448 0.625,0.26 10 false F55 0.646,1.365 1.271,1.625 0.625,0.26 10 false ESS 2.51,1.365 3.135,1.625 0.625,0.26 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F55-3 (CANH) - F55-2 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F55-3 (CANH) - F55-1 (ESS) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F55-2 (CANL) - F55-1 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F55-3 (CANH) - F55-5 (BAT) BE - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F55-2 (CANL) - F55-5 (BAT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYBRID VEHICLE CONTROL ECU


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F2 and F3 hybrid vehicle control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

C350875C01
1.781,0.188 2.146,0.458 0.365,0.271 5.135,0.188 5.5,0.458 0.365,0.271 2.042,1.385 2.042,0.719 2.042,0.719 1.917,0.719 true 2.167,1.385 2.167,0.719 2.167,0.719 2.292,0.719 true 2.24,1.563 2.24,2.115 2.24,2.115 2.365,2.115 true 2.104,1.563 2.104,2.115 2.104,2.115 1.958,2.115 true 4.385,1.667 4.385,2.135 4.385,2.135 4.24,2.135 true 4.656,1.406 4.656,0.74 4.656,0.74 4.531,0.74 true 1.51,0.656 2.125,0.854 0.615,0.198 10 false CA3P 1.542,2.052 2.156,2.25 0.615,0.198 10 false CA3N 2.438,2.052 3.052,2.25 0.615,0.198 10 false CA1H 2.365,0.656 2.979,0.854 0.615,0.198 10 false CA1L 0.104,0.083 0.719,0.281 0.615,0.198 10 false *a 1.885,0.26 2.5,0.458 0.615,0.198 10 false F2 5.25,0.26 5.865,0.458 0.615,0.198 10 false F3 3.833,2.073 4.448,2.271 0.615,0.198 10 false BATT 4.292,0.688 4.906,0.885 0.615,0.198 10 false E1
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F2-21 (CA1H) - F2-8 (CA1L) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F2-21 (CA1H) - F3-3 (E1) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F2-8 (CA1L) - F3-3 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F2-21 (CA1H) - F3-27 (BATT) L - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F2-8 (CA1L) - F3-27 (BATT) W - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F2-7 (CA3P) - F2-20 (CA3N) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F2-7 (CA3P) - F3-3 (E1) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F2-20 (CA3N) - F3-3 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F2-7 (CA3P) - F3-27 (BATT) G - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F2-20 (CA3N) - F3-27 (BATT) W - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




INVERTER WITH CONVERTER ASSEMBLY


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the C33 inverter with converter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350876C01
4.99,0.25 5.396,0.531 0.406,0.281 1.875,0.135 2.281,0.417 0.406,0.281 1.688,1.219 1.688,0.406 1.688,0.406 1.542,0.406 true 1.135,1.344 1.656,1.344 true 2.229,1.542 3.063,1.552 true 6,2.135 5.844,2.135 5.844,2.135 5.844,1.667 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.094,0.354 1.583,0.594 0.49,0.24 10 false CANH 0.677,1.281 1.167,1.521 0.49,0.24 10 false CANL 3.135,1.49 3.625,1.729 0.49,0.24 10 false GND1 6.073,2.063 6.563,2.302 0.49,0.24 10 false BAT 5.073,0.323 5.563,0.563 0.49,0.24 10 false F29 1.958,0.208 2.448,0.448 0.49,0.24 10 false C33 3.729,0.146 4.042,0.344 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C33-1 (CANH) - C33-7 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
C33-1 (CANH) - C33-24 (GND1) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C33-7 (CANL) - C33-24 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C33-1 (CANH) - F29-16 (BAT) GR - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
C33-7 (CANL) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A40 and C31 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

C349827C02
1.229,0.313 1.625,0.563 0.396,0.25 4.417,0.271 4.823,0.49 0.406,0.219 2.125,1.25 2.125,0.49 2.125,0.49 2.25,0.49 true 2,2.313 2.125,2.313 2.125,2.313 2.125,1.375 true 2.948,1.385 2.948,0.458 2.948,0.458 3.073,0.458 true 3.042,1.375 3.042,0.615 3.042,0.615 3.167,0.615 true 0.885,1.25 0.885,0.49 0.885,0.49 0.75,0.49 true 6.177,1.396 6.177,0.542 6.177,0.542 6.302,0.542 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.51,0.323 4.823,0.521 0.313,0.198 10 false C31 1.323,0.375 1.635,0.573 0.313,0.198 10 false A40 2.333,0.427 2.958,0.635 0.625,0.208 10 false CANH 1.615,2.271 2.24,2.479 0.625,0.208 10 false CANL 3.156,0.396 3.781,0.604 0.625,0.208 10 false CAN+ 3.25,0.552 3.875,0.76 0.625,0.208 10 false CAN- 0.333,0.417 0.958,0.625 0.625,0.208 10 false BATT 6.396,0.469 6.698,0.677 0.302,0.208 10 false E1
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A40-13 (CANH) - A40-26 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A40-13 (CANH) - C31-59 (E1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-26 (CANL) - C31-59 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-13 (CANH) - A40-1 (BATT) R - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A40-26 (CANL) - A40-1 (BATT) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C31-31 (CAN+) - C31-32 (CAN-) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
C31-31 (CAN+) - C31-59 (E1) SB - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C31-32 (CAN-) - C31-59 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C31-31 (CAN+) - A40-1 (BATT) SB - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
C31-32 (CAN-) - A40-1 (BATT) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




METER CIRCUIT PLATE


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.
C349828C04
1.552,0.615 1.938,0.896 0.385,0.281 1.021,2.927 1.156,2.927 1.156,2.927 1.156,2.135 true 1.448,2.927 1.292,2.927 1.292,2.927 1.292,2.135 true 0.51,2.604 0.646,2.604 0.646,2.604 0.646,2.125 true 1.583,2.625 1.427,2.625 1.427,2.625 1.427,2.125 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.667,2.563 2.25,2.865 0.583,0.302 10 false ES 0.594,2.865 1.177,3.167 0.583,0.302 10 false CANH 1.688,0.688 2.271,0.99 0.583,0.302 10 false F6 0.354,2.542 0.938,2.844 0.583,0.302 10 false B 1.521,2.865 2.104,3.167 0.583,0.302 10 false CANL
*a Front view of wire harness connector
(to Meter Circuit Plate)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F6-26 (CANH) - F6-27 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F6-26 (CANH) - F6-28 (ES) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F6-27 (CANL) - F6-28 (ES) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F6-26 (CANH) - F6-22 (B) V - W*1
V - GR*2
HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F6-27 (CANL) - F6-22 (B) W - W*1
W - GR*2
LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


·

*1: for LHD

·

*2: for RHD




COMBINATION METER MIRROR ECU (w/ Headup Display System)


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.
C349829C02
1.521,0.115 1.865,0.375 0.344,0.26 1.656,1.146 1.656,0.531 1.656,0.531 1.406,0.531 true 1.781,1.146 1.781,0.542 1.781,0.542 2.01,0.542 true 0.875,1.219 1.26,1.219 true 1.906,1.146 1.906,1.021 1.906,1.021 2.552,1.021 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.979,0.469 1.479,0.698 0.5,0.229 10 false CANH 2.083,0.469 2.583,0.698 0.5,0.229 10 false CANL 1.625,0.188 2.125,0.417 0.5,0.229 10 false G7 0.698,1.146 1.198,1.375 0.5,0.229 10 false B 2.615,0.938 3.115,1.167 0.5,0.229 10 false ES
*a Front view of wire harness connector
(to Combination Meter Mirror ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G7-4 (CANH) - G7-5 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G7-4 (CANH) - G7-6 (ES) P - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G7-5 (CANL) - G7-6 (ES) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G7-4 (CANH) - G7-1 (B) P - G HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G7-5 (CANL) - G7-1 (B) W - G LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A41 brake booster with master cylinder assembly connector.


c.
C349830C03
1.542,0.146 1.958,0.417 0.417,0.271 1.625,1.656 1.625,0.625 1.625,0.625 1.75,0.625 true 1.531,1.656 1.531,0.625 1.531,0.625 1.396,0.625 true 1.396,2.604 1.531,2.604 1.531,2.604 1.531,1.948 true 1.76,2.604 1.615,2.604 1.615,2.604 1.615,1.948 true 2.646,1.448 2.646,0.417 2.646,0.417 2.771,0.417 true 2.781,2.542 2.635,2.542 2.635,2.542 2.635,1.885 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.646,0.219 1.958,0.417 0.313,0.198 10 false A41 1.833,0.552 2.385,0.833 0.552,0.281 10 false CA2H 1.01,0.552 1.563,0.833 0.552,0.281 10 false CA2L 1,2.531 1.552,2.813 0.552,0.281 10 false CA1L 1.854,2.542 2.406,2.823 0.552,0.281 10 false CA1H 2.844,0.333 3.396,0.615 0.552,0.281 10 false GND1 2.844,2.469 3.146,2.74 0.302,0.271 10 false BS
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A41-30 (CA2H) - A41-29 (CA2L) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A41-30 (CA2H) - A41-26 (GND1) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-29 (CA2L) - A41-26 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-30 (CA2H) - A41-52 (BS) P - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A41-29 (CA2L) - A41-52 (BS) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A41-43 (CA1H) - A41-42 (CA1L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A41-43 (CA1H) - A41-26 (GND1) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-42 (CA1L) - A41-26 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-43 (CA1H) - A41-52 (BS) G - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A41-42 (CA1L) - A41-52 (BS) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F17 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C350877C01
4.948,0.146 5.333,0.406 0.385,0.26 1.75,0.115 2.135,0.375 0.385,0.26 5.135,1.094 5.135,0.667 5.135,0.667 5.021,0.667 true 5.969,2.115 5.844,2.115 5.844,2.115 5.844,1.677 true 2.24,1.365 2.24,0.688 2.24,0.688 2.365,0.688 true 2.135,1.365 2.135,0.521 2.135,0.521 2.26,0.521 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 4.729,0.583 5.042,0.781 0.313,0.198 10 false CG 6.042,2.042 6.354,2.24 0.313,0.198 10 false BAT 5.021,0.208 5.333,0.406 0.313,0.198 10 false F29 1.823,0.167 2.135,0.365 0.313,0.198 10 false F17 2.438,0.615 3.042,0.865 0.604,0.25 10 false CANH 2.333,0.438 2.938,0.688 0.604,0.25 10 false CANL 3.75,0.073 4.063,0.271 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F17-14 (CANH) - F17-13 (CANL) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F17-14 (CANH) - F29-4 (CG) SB - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F17-13 (CANL) - F29-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F17-14 (CANH) - F29-16 (BAT) SB - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F17-13 (CANL) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


c.
C348744C05
1.5,0.385 1.865,0.667 0.365,0.281 1.198,1.635 1.198,0.875 1.198,0.875 1.375,0.875 true 1.073,1.635 1.073,0.875 1.073,0.875 0.906,0.875 true 2.385,1.646 2.385,0.885 2.385,0.885 2.563,0.885 true 1.24,2.719 1.073,2.719 1.073,2.719 1.073,2.052 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.604,0.458 1.917,0.656 0.313,0.198 10 false F1 0.479,0.802 1.115,1 0.635,0.198 10 false CANH 1.458,0.802 2.094,1 0.635,0.198 10 false CANL 2.646,0.802 2.958,1 0.313,0.198 10 false +B 1.302,2.646 1.938,2.844 0.635,0.198 10 false E
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F1-1 (CANH) - F1-2 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F1-1 (CANH) - F1-18 (E) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F1-2 (CANL) - F1-18 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F1-1 (CANH) - F1-4 (+B) R - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F1-2 (CANL) - F1-4 (+B) W - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F20 and F54 power steering ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C350878C01
2.063,0.115 2.448,0.375 0.385,0.26 5.01,0.156 5.396,0.417 0.385,0.26 2.313,1.854 2.313,0.573 2.313,0.573 2.458,0.573 true 2.448,1.854 2.448,0.802 2.448,0.802 2.594,0.802 true 4.938,1.667 4.927,0.656 4.927,0.656 5.073,0.656 true 5.51,1.667 5.51,0.875 5.51,0.875 5.656,0.875 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 2.531,0.5 3.01,0.74 0.479,0.24 10 false CANH 2.667,0.729 3.146,0.969 0.479,0.24 10 false CANL 2.135,0.167 2.615,0.406 0.479,0.24 10 false F20 5.083,0.208 5.563,0.448 0.479,0.24 10 false F54 5.156,0.583 5.635,0.823 0.479,0.24 10 false PIG 5.729,0.802 6.208,1.042 0.479,0.24 10 false PGND
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F20-7 (CANH) - F20-8 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F20-7 (CANH) - F54-2 (PGND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F20-8 (CANL) - F54-2 (PGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F20-7 (CANH) - F54-1 (PIG) V - B-W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F20-8 (CANL) - F54-1 (PIG) W - B-W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ Simple Intelligent Parking Assist System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F26 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350879C01
1.688,0.188 2.104,0.458 0.417,0.271 5.073,0.177 5.49,0.448 0.417,0.271 2.938,1.25 2.938,0.333 2.938,0.333 3.073,0.333 true 3.063,1.25 3.063,0.563 3.063,0.563 3.198,0.563 true 2.042,2.052 1.906,2.052 1.906,2.052 1.906,1.469 true 6.063,2.104 5.927,2.104 5.927,2.104 5.927,1.677 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.917,0.115 4.229,0.313 0.313,0.198 10 false *1 3.146,0.26 3.458,0.458 0.313,0.198 10 false R1 3.281,0.49 3.594,0.688 0.313,0.198 10 false R2 1.781,0.24 2.167,0.51 0.385,0.271 10 false F26 2.146,1.969 2.458,2.167 0.313,0.198 10 false E 6.135,2.031 6.656,2.24 0.521,0.208 10 false BAT 5.177,0.229 5.563,0.5 0.385,0.271 10 false F29
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F26-17 (R1) - F26-18 (R2) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F26-17 (R1) - F26-30 (E) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F26-18 (R2) - F26-30 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F26-17 (R1) - F29-16 (BAT) LG - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F26-18 (R2) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F56 airbag ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350880C01
1.698,0.094 2.073,0.323 0.375,0.229 5.094,0.375 5.469,0.604 0.375,0.229 1.5,1.292 1.5,0.479 1.5,0.479 1.333,0.479 true 1.948,2.427 1.802,2.427 1.802,2.427 1.802,1.781 true 1.198,2.438 1.333,2.438 1.333,2.438 1.333,1.792 true 6.073,2.198 5.927,2.198 5.927,2.198 5.927,1.667 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 3.76,0.094 4.073,0.292 0.313,0.198 10 false *1 1.771,0.135 2.083,0.333 0.313,0.198 10 false F56 0.875,0.406 1.365,0.635 0.49,0.229 10 false CANH 0.75,2.344 1.24,2.573 0.49,0.229 10 false CANL 2.031,2.354 2.521,2.583 0.49,0.229 10 false E1 5.167,0.406 5.479,0.604 0.313,0.198 10 false F29 6.167,2.115 6.656,2.344 0.49,0.229 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F56-13 (CANH) - F56-22 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F56-13 (CANH) - F56-25 (E1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F56-22 (CANL) - F56-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F56-13 (CANH) - F29-16 (BAT) R - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F56-22 (CANL) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F58 air conditioning amplifier assembly connector.


c.
C349836C04
1.5,0.208 1.917,0.479 0.417,0.271 1.885,1.833 1.885,0.729 1.885,0.729 2.052,0.729 true 2.021,1.833 2.021,0.938 2.021,0.938 2.188,0.938 true 0.844,1.604 0.844,0.99 0.844,0.99 0.969,0.99 true 2.583,1.604 2.583,1.135 2.583,1.135 2.75,1.135 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.604,0.281 1.917,0.479 0.313,0.198 10 false F58 2.146,0.667 2.813,0.875 0.667,0.208 10 false CANH 2.271,0.875 2.938,1.083 0.667,0.208 10 false CANL 2.813,1.063 3.281,1.292 0.469,0.229 10 false GND 1.052,0.917 1.521,1.146 0.469,0.229 10 false B
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F58-11 (CANH) - F58-12 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F58-11 (CANH) - F58-4 (GND) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F58-12 (CANL) - F58-4 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F58-11 (CANH) - F58-1 (B) BE - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F58-12 (CANL) - F58-1 (B) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F92 and F93 navigation receiver assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C350890C02
1.667,0.177 2.021,0.417 0.354,0.24 5.052,0.188 5.406,0.427 0.354,0.24 2.188,1.417 2.188,0.76 2.188,0.76 2.344,0.76 true 2.073,1.417 2.073,0.531 2.073,0.531 2.229,0.531 true 5.781,1.292 5.781,0.75 5.781,0.75 5.938,0.75 true 5.167,1.708 5.167,2.229 5.167,2.229 5.323,2.229 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.729,0.219 2.042,0.417 0.313,0.198 10 false F92 2.313,0.469 2.958,0.667 0.646,0.198 10 false CANH 2.427,0.688 3.073,0.885 0.646,0.198 10 false CANL 5.115,0.229 5.427,0.427 0.313,0.198 10 false F93 6.01,0.667 6.438,0.875 0.427,0.208 10 false +B1 5.417,2.146 5.906,2.365 0.49,0.219 10 false GND1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F92-9 (CANH) - F92-10 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F92-9 (CANH) - F93-7 (GND1) L - LA-BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F92-10 (CANL) - F93-7 (GND1) W - LA-BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F92-9 (CANH) - F93-4 (+B1) L - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F92-10 (CANL) - F93-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F31 and F32 radio and display receiver assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C350890C01
1.667,0.177 2.021,0.417 0.354,0.24 5.052,0.188 5.406,0.427 0.354,0.24 2.188,1.417 2.188,0.76 2.188,0.76 2.344,0.76 true 2.073,1.417 2.073,0.531 2.073,0.531 2.229,0.531 true 5.781,1.292 5.781,0.75 5.781,0.75 5.938,0.75 true 5.167,1.708 5.167,2.229 5.167,2.229 5.323,2.229 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.729,0.219 2.042,0.417 0.313,0.198 10 false F31 2.313,0.469 2.958,0.667 0.646,0.198 10 false CANH 2.427,0.688 3.073,0.885 0.646,0.198 10 false CANL 5.115,0.229 5.427,0.427 0.313,0.198 10 false F32 6.01,0.667 6.438,0.875 0.427,0.208 10 false +B1 5.417,2.146 5.906,2.365 0.49,0.219 10 false GND1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F31-9 (CANH) - F31-10 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F31-9 (CANH) - F32-7 (GND1) L - LA-BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F31-10 (CANL) - F32-7 (GND1) W - LA-BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F31-9 (CANH) - F32-4 (+B1) L - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F31-10 (CANL) - F32-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R5 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350889C01
1.865,0.146 2.188,0.365 0.323,0.219 5.021,0.135 5.396,0.385 0.375,0.25 1.885,1.292 1.885,0.51 1.885,0.51 1.708,0.51 true 1.719,2.281 1.875,2.281 1.875,2.281 1.875,1.698 true 5.125,1.115 5.125,0.635 5.125,0.635 4.948,0.635 true 6,2.156 5.833,2.156 5.833,2.156 5.833,1.667 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.938,0.188 2.25,0.385 0.313,0.198 10 false R5 1.25,2.229 1.833,2.458 0.583,0.229 10 false CANH 1.281,0.458 1.865,0.688 0.583,0.229 10 false CANL 5.104,0.188 5.417,0.385 0.313,0.198 10 false F29 4.667,0.583 5.25,0.813 0.583,0.229 10 false CG 6.115,2.083 6.698,2.313 0.583,0.229 10 false BAT 3.771,0.073 4.083,0.271 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-4 (CANH) - R5-1 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
R5-4 (CANH) - F29-4 (CG) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-1 (CANL) - F29-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-4 (CANH) - F29-16 (BAT) LG - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R5-1 (CANL) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A18 No. 1 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C350881C01
1.604,0.146 2,0.385 0.396,0.24 5.125,0.208 5.521,0.448 0.396,0.24 2.823,2.313 2.698,2.313 2.698,2.313 2.698,1.667 true 2.448,2.302 2.583,2.302 2.583,2.302 2.583,1.656 true 0.885,2.26 1.021,2.26 1.021,2.26 1.021,1.646 true 6.063,2.104 5.938,2.104 5.938,2.104 5.938,1.667 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 3.729,0.094 4.042,0.292 0.313,0.198 10 false *1 5.219,0.26 5.531,0.458 0.313,0.198 10 false F29 2.896,2.24 3.365,2.469 0.469,0.229 10 false CANH 2.01,2.24 2.479,2.469 0.469,0.229 10 false CANL 0.51,2.198 0.979,2.427 0.469,0.229 10 false GND 1.677,0.198 1.99,0.396 0.313,0.198 10 false A18 6.135,2.031 6.604,2.26 0.469,0.229 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly LH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A18-24 (CANH) - A18-23 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A18-24 (CANH) - A18-12 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A18-23 (CANL) - A18-12 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A18-24 (CANH) - F29-16 (BAT) L - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A18-23 (CANL) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SWING GRILLE ACTUATOR ASSEMBLY (w/ Occupant Classification System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A36 swing grille actuator assembly connector.


c.
C350810C01
1.469,0.083 1.906,0.365 0.438,0.281 2.031,1.323 2.406,1.323 true 2.042,0.99 2.417,0.99 true 1.031,0.99 1.406,0.99 true 1.031,1.313 1.406,1.313 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 2.5,0.927 2.99,1.188 0.49,0.26 10 false CANP 0.573,1.26 1.063,1.521 0.49,0.26 10 false CANN 0.656,0.927 1.146,1.188 0.49,0.26 10 false GND 2.5,1.26 2.99,1.521 0.49,0.26 10 false +B 1.563,0.156 2.052,0.417 0.49,0.26 10 false A36
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A36-2 (CANP) - A36-3 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A36-2 (CANP) - A36-1 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A36-3 (CANN) - A36-1 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A36-2 (CANP) - A36-4 (+B) L - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A36-3 (CANN) - A36-4 (+B) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SWING GRILLE ACTUATOR ASSEMBLY (w/o Occupant Classification System and with Grille Shutter System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A37 swing grille actuator assembly connector.


c.
C349838C03
1.458,0.156 1.875,0.417 0.417,0.26 2.26,1.792 2.115,1.792 2.115,1.792 2.115,1.219 true 2.094,1.979 1.948,1.979 1.948,1.979 1.948,1.219 true 1.302,1.104 1.302,0.5 1.302,0.5 1.146,0.5 true 1.479,1.792 1.625,1.792 1.625,1.792 1.625,1.219 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 2.333,1.729 2.771,1.927 0.438,0.198 10 false CANP 2.177,1.917 2.615,2.115 0.438,0.198 10 false CANN 1.552,0.219 1.99,0.417 0.438,0.198 10 false A37 0.885,0.427 1.49,0.656 0.604,0.229 10 false +B 1.115,1.729 1.552,1.927 0.438,0.198 10 false GND
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A37-6 (CANP) - A37-5 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A37-6 (CANP) - A37-3 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A37-5 (CANN) - A37-3 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A37-6 (CANP) - A37-1 (+B) L - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A37-5 (CANN) - A37-1 (+B) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M55 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C350884C01
1.688,0.135 2.115,0.427 0.427,0.292 4.979,0.208 5.406,0.5 0.427,0.292 1.76,1.302 1.76,0.615 1.76,0.615 1.604,0.615 true 1.615,2.219 1.76,2.219 1.76,2.219 1.76,1.563 true 2.375,2.219 2.219,2.219 2.219,2.219 2.219,1.563 true 6,2.115 5.844,2.115 5.844,2.115 5.844,1.667 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 3.635,0.073 3.948,0.271 0.313,0.198 10 false *1 1.771,0.219 2.094,0.417 0.323,0.198 10 false M55 5.073,0.292 5.396,0.49 0.323,0.198 10 false F29 1.198,2.156 1.688,2.406 0.49,0.25 10 false CA1N 1.177,0.552 1.667,0.802 0.49,0.25 10 false CA1P 2.448,2.156 2.938,2.406 0.49,0.25 10 false BLGD 6.083,2.052 6.573,2.302 0.49,0.25 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M55-2 (CA1P) - M55-7 (CA1N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
M55-2 (CA1P) - M55-10 (BLGD) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M55-7 (CA1N) - M55-10 (BLGD) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M55-2 (CA1P) - F29-16 (BAT) B - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M55-7 (CA1N) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




DRIVING SUPPORT ECU ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F40 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350885C01
1.583,0.146 1.958,0.406 0.375,0.26 5.01,0.188 5.406,0.458 0.396,0.271 2.719,1.271 2.719,0.583 2.719,0.583 2.865,0.583 true 2.583,1.271 2.583,0.583 2.583,0.583 2.448,0.583 true 5.833,1.667 5.833,2.156 5.833,2.156 5.969,2.156 true 2.458,1.542 2.458,2.031 2.458,2.031 2.323,2.031 true 1.667,0.208 2.125,0.406 0.458,0.198 10 false F40 0.104,0.094 0.563,0.292 0.458,0.198 10 false *a 3.76,0.094 4.219,0.292 0.458,0.198 10 false *1 2.01,0.531 2.51,0.76 0.5,0.229 10 false CA2H 2.948,0.531 3.448,0.76 0.5,0.229 10 false CA2L 1.958,1.969 2.458,2.198 0.5,0.229 10 false GND 5.094,0.25 5.552,0.448 0.458,0.198 10 false F29 6.052,2.094 6.552,2.323 0.5,0.229 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F40-10 (CA2H) - F40-11 (CA2L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F40-10 (CA2H) - F40-28 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F40-11 (CA2L) - F40-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F40-10 (CA2H) - F29-16 (BAT) G - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F40-11 (CA2L) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the O7 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

C350886C01
1.823,0.146 2.146,0.396 0.323,0.25 4.979,0.198 5.385,0.469 0.406,0.271 2.219,1.688 2.219,2.125 2.219,2.125 2.375,2.125 true 2.219,1.323 2.219,0.583 2.219,0.583 2.375,0.583 true 2.063,1.688 2.063,2.125 2.063,2.125 1.927,2.125 true 5.844,1.677 5.844,2.073 5.844,2.073 6,2.073 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 3.781,0.094 4.094,0.292 0.313,0.198 10 false *1 1.896,0.198 2.208,0.396 0.313,0.198 10 false O7 2.458,0.51 2.927,0.729 0.469,0.219 10 false CA1P 2.458,2.063 2.927,2.281 0.469,0.219 10 false CA1N 1.573,2.063 2.042,2.281 0.469,0.219 10 false GND 5.073,0.26 5.385,0.458 0.313,0.198 10 false F29 6.083,2.01 6.552,2.229 0.469,0.219 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O7-5 (CA1P) - O7-11 (CA1N) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
O7-5 (CA1P) - O7-10 (GND) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O7-11 (CA1N) - O7-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O7-5 (CA1P) - F29-16 (BAT) GR - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O7-11 (CA1N) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A2 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350887C01
4.99,0.208 5.354,0.479 0.365,0.271 1.74,0.115 2.104,0.385 0.365,0.271 2.073,1.26 2.073,0.573 2.073,0.573 2.229,0.573 true 1.906,1.26 1.906,0.573 1.906,0.573 1.729,0.573 true 0.99,1.344 1.688,1.344 true 5.979,2.073 5.823,2.073 5.823,2.073 5.833,1.667 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *1 1.323,0.51 1.802,0.719 0.479,0.208 10 false CA2L 2.354,0.521 2.833,0.729 0.479,0.208 10 false CA2H 0.531,1.281 1.01,1.49 0.479,0.208 10 false SGND 6.094,2.01 6.573,2.219 0.479,0.208 10 false BAT 5.063,0.281 5.385,0.479 0.323,0.198 10 false F29 1.844,0.177 2.167,0.375 0.323,0.198 10 false A2
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-3 (CA2H) - A2-2 (CA2L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A2-3 (CA2H) - A2-1 (SGND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-2 (CA2L) - A2-1 (SGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-3 (CA2H) - F29-16 (BAT) G - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A2-2 (CA2L) - F29-16 (BAT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OCCUPANT DETECTION ECU (w/ Occupant Classification System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the a11 occupant detection ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

C350888C02
1.729,0.115 2.115,0.365 0.385,0.25 5,0.125 5.396,0.396 0.396,0.271 2.219,1.323 2.219,0.573 2.219,0.573 2.354,0.573 true 2.073,1.323 2.073,0.573 2.073,0.573 1.927,0.573 true 2.365,2.219 2.219,2.219 2.219,2.219 2.219,1.552 true 5.99,2.021 5.844,2.021 5.844,2.021 5.844,1.667 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 3.792,0.115 4.104,0.313 0.313,0.198 10 false *1 2.438,0.51 2.979,0.729 0.542,0.219 10 false CANH 1.469,0.51 2.01,0.729 0.542,0.219 10 false CANL 2.448,2.156 2.99,2.375 0.542,0.219 10 false GND 1.823,0.167 2.365,0.385 0.542,0.219 10 false a11 5.083,0.188 5.625,0.406 0.542,0.219 10 false F29 6.083,1.948 6.625,2.167 0.542,0.219 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Occupant Detection ECU)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
a11-5 (CANH) - a11-4 (CANL) R - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
a11-5 (CANH) - a11-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
a11-4 (CANL) - a11-10 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
a11-5 (CANH) - F29-16 (BAT) R - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
a11-4 (CANL) - F29-16 (BAT) SB - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher