Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 5 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Main body ECU (multiplex network body ECU)

·

No. 1 headlight ECU sub-assembly LH

·

Certification ECU (smart key ECU assembly)

·

Central gateway ECU (network gateway ECU)

·

Meter circuit plate

·

Air conditioning amplifier assembly

·

Combination meter mirror ECU

(w/ Headup Display System)

·

No. 3 CAN junction connector



WIRING DIAGRAM

C346809E06
0.917,6.458 1.531,6.656 0.615,0.198 10 false CA5H 0.938,7 1.552,7.198 0.615,0.198 10 false CA5L 0.375,7.542 2.323,8.021 1.948,0.479 10 false Central Gateway ECU (Network Gateway ECU) 1.417,6.448 1.729,6.646 0.313,0.198 10 false 15 1.406,7 1.719,7.198 0.313,0.198 10 false 16 3.146,6.438 3.302,6.635 0.156,0.198 10 false 6 3.104,6.969 3.417,7.167 0.313,0.198 10 false 17 0.406,1.583 2.063,2.115 1.656,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 3.135,0.5 3.292,0.698 0.156,0.198 10 false 2 3.094,1.031 3.406,1.229 0.313,0.198 10 false 13 1.427,0.51 1.74,0.708 0.313,0.198 10 false 14 1.417,1.031 1.729,1.229 0.313,0.198 10 false 13 0.875,0.646 1.49,0.844 0.615,0.198 10 false CANH 0.896,1.167 1.51,1.365 0.615,0.198 10 false CANL 3.146,2.396 3.302,2.594 0.156,0.198 10 false 3 3.104,2.938 3.417,3.135 0.313,0.198 10 false 14 1.427,2.417 1.74,2.615 0.313,0.198 10 false 24 1.427,2.948 1.74,3.146 0.313,0.198 10 false 23 0.438,3.49 3,3.865 2.563,0.375 10 false No. 1 Headlight ECU Sub-assembly LH 0.865,2.542 1.479,2.74 0.615,0.198 10 false CANH 0.896,3.073 1.51,3.271 0.615,0.198 10 false CANL 4.167,2.406 4.323,2.604 0.156,0.198 10 false 4 4.125,2.938 4.438,3.135 0.313,0.198 10 false 15 5.583,3.479 7.146,3.896 1.563,0.417 10 false Air Conditioning Amplifier Assembly 5.99,2.521 6.604,2.719 0.615,0.198 10 false CANH 5.99,3.063 6.604,3.26 0.615,0.198 10 false CANL 5.646,2.396 5.958,2.594 0.313,0.198 10 false 11 5.656,2.948 5.969,3.146 0.313,0.198 10 false 12 3.146,4.385 3.302,4.583 0.156,0.198 10 false 5 3.094,4.927 3.406,5.125 0.313,0.198 10 false 16 1.438,4.385 1.594,4.583 0.156,0.198 10 false 1 1.438,4.917 1.594,5.115 0.156,0.198 10 false 2 0.865,4.521 1.479,4.719 0.615,0.198 10 false CANH 0.885,5.063 1.5,5.26 0.615,0.198 10 false CANL 0.375,6.844 1.146,7.042 0.771,0.198 10 false 120 Ω 6.458,0.885 6.99,1.146 0.531,0.26 10 false 120 Ω 0.448,5.469 2.26,5.896 1.813,0.427 10 false Certification ECU (Smart Key ECU Assembly) 4.167,4.396 4.323,4.594 0.156,0.198 10 false 7 4.146,4.927 4.458,5.125 0.313,0.198 10 false 18 5.719,4.396 5.875,4.594 0.156,0.198 10 false 4 5.719,4.927 5.875,5.125 0.156,0.198 10 false 5 5.99,4.521 6.604,4.719 0.615,0.198 10 false CANH 6,5.042 6.615,5.24 0.615,0.198 10 false CANL 5.802,5.469 6.979,6.083 1.177,0.615 10 false Combination Meter Mirror ECU* 4.177,0.51 4.333,0.708 0.156,0.198 10 false 1 4.146,1.042 4.458,1.24 0.313,0.198 10 false 12 5.646,0.5 5.958,0.698 0.313,0.198 10 false 26 5.656,1.021 5.969,1.219 0.313,0.198 10 false 27 5.969,0.521 6.583,0.719 0.615,0.198 10 false CANH 5.969,1.042 6.583,1.24 0.615,0.198 10 false CANL 5.917,1.583 7.104,1.99 1.188,0.406 10 false Meter Circuit Plate 3.156,7.573 4.417,7.99 1.26,0.417 10 false No. 3 CAN Junction Connector 0.104,1.583 0.563,1.781 0.458,0.198 10 false F17 0.115,3.49 0.573,3.688 0.458,0.198 10 false A18 0.188,5.469 0.5,5.667 0.313,0.198 10 false F1 0.073,7.542 0.531,7.74 0.458,0.198 10 false F59 2.844,7.573 3.302,7.771 0.458,0.198 10 false F71 5.698,1.573 6.01,1.771 0.313,0.198 10 false F6 5.24,3.479 5.698,3.677 0.458,0.198 10 false F58 5.563,5.469 5.875,5.667 0.313,0.198 10 false G7 5.167,8.344 7.156,8.646 1.99,0.302 10 false *: w/ Headup Display System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 33 seconds. Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and wait for approximately 52 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F71 No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C351159C09
0.281,1.354 0.667,1.615 0.385,0.26 3.646,1.333 4.031,1.594 0.385,0.26 1.385,1.417 1.385,0.604 1.385,0.604 1.146,0.604 true 1.219,1.427 1.219,0.781 1.219,0.781 0.979,0.781 true 1.708,1.438 1.719,0.25 1.719,0.25 1.542,0.25 true 1.552,1.427 1.552,0.438 1.552,0.438 1.313,0.438 true 1.885,1.438 1.885,0.156 1.885,0.156 2.073,0.156 true 5.417,0.677 5.25,0.677 5.25,0.677 5.25,1.156 true 1,2.063 1.208,2.063 1.208,2.063 1.208,1.708 true 1.177,2.25 1.385,2.25 1.385,2.25 1.385,1.719 true 1.375,2.448 1.552,2.448 1.552,2.448 1.552,1.708 true 1.542,2.656 1.719,2.656 1.719,2.656 1.719,1.708 true 2.219,2.406 2.052,2.406 2.052,2.406 2.052,1.708 true 2.052,1.427 2.052,0.365 2.052,0.365 2.198,0.365 true 2.219,1.427 2.219,0.615 2.219,0.615 2.365,0.615 true 2.052,2.656 1.885,2.656 1.885,2.656 1.885,1.708 true 2.385,2.156 2.219,2.156 2.219,2.156 2.219,1.688 true 0.365,1.406 0.719,1.615 0.354,0.208 10 false F71 0.396,0.708 0.969,0.969 0.573,0.26 10 false CANH*b 0.583,0.531 1.156,0.792 0.573,0.26 10 false CANH*c 0.74,0.354 1.313,0.615 0.573,0.26 10 false CANH*d 0.948,0.188 1.521,0.448 0.573,0.26 10 false CANH*e 2.156,0.083 2.729,0.344 0.573,0.26 10 false CANH*f 3.729,1.375 4.083,1.583 0.354,0.208 10 false F29 5.51,0.604 5.875,0.865 0.365,0.26 10 false CG 0.438,2 1.01,2.26 0.573,0.26 10 false CANL*b 0.604,2.177 1.177,2.438 0.573,0.26 10 false CANL*c 0.792,2.365 1.365,2.625 0.573,0.26 10 false CANL*d 0.99,2.563 1.563,2.771 0.573,0.208 10 false CANL*e 2.135,2.573 2.708,2.74 0.573,0.167 10 false CANL*f 0.073,0.063 0.646,0.323 0.573,0.26 10 false *a 3.969,0.073 4.542,0.333 0.573,0.26 10 false *1 2.281,0.292 2.854,0.552 0.573,0.26 10 false CANH*g 2.438,0.531 3.01,0.792 0.573,0.26 10 false CANH*h 2.302,2.333 2.875,2.594 0.573,0.26 10 false CANL*g 2.479,2.073 3.052,2.333 0.573,0.26 10 false CANL*h
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Meter Circuit Plate
*c to Main Body ECU (Multiplex Network Body ECU) *d to No. 1 Headlight ECU Sub-assembly LH
*e to Air Conditioning Amplifier Assembly *f to Certification ECU (Smart Key ECU Assembly)
*g to Central Gateway ECU (Network Gateway ECU) *h to Combination Meter Mirror ECU
(w/ Headup Display System)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F71-1 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Meter circuit plate
F71-12 (CANL) - F29-4 (CG)
F71-2 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
F71-13 (CANL) - F29-4 (CG)
F71-3 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 1 headlight ECU sub-assembly LH
F71-14 (CANL) - F29-4 (CG)
F71-4 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Air conditioning amplifier assembly
F71-15 (CANL) - F29-4 (CG)
F71-5 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)
F71-16 (CANL) - F29-4 (CG)
F71-6 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F71-17 (CANL) - F29-4 (CG)
F71-7 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Combination meter mirror ECU*
F71-18 (CANL) - F29-4 (CG)


*: w/ Headup Display System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F59 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C351159C10
0.281,1.354 0.667,1.615 0.385,0.26 3.646,1.333 4.031,1.594 0.385,0.26 2.052,1.417 2.052,0.563 2.052,0.563 2.24,0.563 true 5.417,0.594 5.25,0.594 5.25,0.594 5.25,1.146 true 2.24,2.302 2.052,2.302 2.052,2.302 2.052,1.698 true 0.365,1.406 0.719,1.615 0.354,0.208 10 false F71 2.313,0.49 2.885,0.75 0.573,0.26 10 false CANH*b 3.729,1.375 4.083,1.583 0.354,0.208 10 false F29 5.5,0.521 5.865,0.781 0.365,0.26 10 false CG 2.313,2.219 2.885,2.479 0.573,0.26 10 false CANL*b 0.073,0.063 0.646,0.323 0.573,0.26 10 false *a 3.969,0.073 4.542,0.333 0.573,0.26 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F71-6 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F71-17 (CANL) - F29-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C351161C04
5.083,0.292 5.49,0.563 0.406,0.271 1.635,0.156 2.042,0.406 0.406,0.25 5.406,0.729 5.26,0.729 5.26,0.729 5.26,1.146 true 2.292,0.708 2.146,0.708 2.146,0.708 2.146,1.427 true 1.906,0.708 2.052,0.708 2.052,0.708 2.052,1.427 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.938,0.063 4.25,0.26 0.313,0.198 10 false *1 5.177,0.354 5.49,0.552 0.313,0.198 10 false F29 5.49,0.646 6.01,0.865 0.521,0.219 10 false CG 1.719,0.198 2.031,0.396 0.313,0.198 10 false F59 1.531,0.635 2,0.844 0.469,0.208 10 false CA5L 2.385,0.635 2.854,0.844 0.469,0.208 10 false CA5H
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F59-15 (CA5H) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F59-16 (CA5L) - F29-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR