Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › THROTTLE BODY
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0241781 THROTTLE BODY A

2ZR-FXE ENGINE CONTROL  THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during throttle body assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body assembly

·

Cleaning the deposits from the throttle body assembly


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module

CAUTION:
A389825

Do not remove the reserve tank cap, air release valve (w/ air release valve) or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


PROCEDURE

Hide 51444C 1.REMOVE REAR MOTOR UNDER COVER LH

Hide 2.DRAIN ENGINE COOLANT (for Engine)

Hide 12601B 3.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17705 4.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.
A374999

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the wire harness clamp.


c.
A375000C01
2.99,1.365 3.177,1.542 0.188,0.177 10 true *a 3,0.729 3.188,0.906 0.188,0.177 10 true *a 0.885,0.49 1.073,0.646 0.188,0.156 10 true *b 0.865,1.667 1.052,1.844 0.188,0.177 10 true *b
*a Clamp
*b Guide


Disengage the 2 clamps.


d.

Disengage the 2 guides and remove the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


e.

Loosen the hose clamp and remove the air cleaner cap sub-assembly from the air cleaner hose assembly.


Hide 5.REMOVE AIR CLEANER HOSE ASSEMBLY

a.
A375001

Slide the clip and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.


b.

Loosen the hose clamp and remove the air cleaner hose assembly from the throttle body assembly.


Hide 22210 6.REMOVE THROTTLE BODY ASSEMBLY

a.
A375002C01
1.844,1.917 2.063,2.094 0.219,0.177 10 true *1 0.875,1.875 1.094,2.052 0.219,0.177 10 true *2 0.021,0.021 0.281,0.229 0.26,0.208 12 false *A 0.052,2.354 0.313,2.563 0.26,0.208 12 false *B 1.781,4.313 2,4.49 0.219,0.177 10 true *1 0.844,4.281 1.063,4.458 0.219,0.177 10 true *2
*A w/ Stud Bolt
*B w/o Stud Bolt
*1 Water By-pass Hose
*2 No. 2 Water By-pass Hose


Disconnect the throttle body assembly connector.


b.

Slide the 2 clips and disconnect the water by-pass hose and No. 2 water by-pass hose from the throttle body assembly.


c.
A378096C01
0.052,0.042 0.323,0.25 0.271,0.208 12 false *A 0.083,2.313 0.354,2.521 0.271,0.208 12 false *B
*A w/ Stud Bolt
*B w/o Stud Bolt


w/ Stud Bolt:

i.

Remove the 2 bolts, 2 nuts and throttle body assembly from the intake manifold.



d.

w/o Stud Bolt:

i.

Remove the 4 bolts and throttle body assembly from the intake manifold.



Hide 22271 7.REMOVE THROTTLE BODY GASKET

a.
A375003C01
0.052,0.042 0.313,0.24 0.26,0.198 12 true *A 0.083,2.333 0.344,2.531 0.26,0.198 12 true *B
*A w/ Stud Bolt
*B w/o Stud Bolt


Remove the throttle body gasket from the intake manifold.