Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM3210E _58 Vehicle Interior _047534 HEATING / AIR CONDITIONING _0244634 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1497/97  BUS IC Communication Malfunction  


DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1497/97 BUS IC Communication Malfunction Error or open in communication line
·

Air conditioning harness assembly

·

No. 1 air conditioning radiator damper servo sub-assembly

·

No. 2 air conditioning radiator damper servo sub-assembly

·

No. 3 air conditioning radiator damper servo sub-assembly

·

Air conditioning amplifier assembly


Memorized
(10 sec. or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

for Dual Type


E341945E01
0.792,9.427 2.906,9.635 2.115,0.208 10 false : LIN Communication Line 0.063,1.552 1.979,1.938 1.917,0.385 10 false No. 2 Air Conditioning Radiator Damper Servo Sub-assembly 0.052,4.313 1.969,4.698 1.917,0.385 10 false No. 3 Air Conditioning Radiator Damper Servo Sub-assembly 3.5,1.594 6.156,1.833 2.656,0.24 10 false Air Conditioning Amplifier Assembly 3.5,1.417 4.104,1.688 0.604,0.271 10 false z1 3.729,1.115 4.073,1.354 0.344,0.24 10 false 4 3.729,0.667 4.073,0.906 0.344,0.24 10 false 3 3.729,0.281 4.073,0.521 0.344,0.24 10 false 2 3.906,1.115 4.635,1.375 0.729,0.26 10 false B BUS 3.917,0.677 4.646,0.938 0.729,0.26 10 false BUS 3.896,0.292 4.625,0.552 0.729,0.26 10 false BUS G 5.021,1.104 5.75,1.365 0.729,0.26 10 false +B 5.073,0.771 5.802,1.031 0.729,0.26 10 false IC 5.333,3.813 6.844,4.042 1.51,0.229 10 false Driver Side Air Mix*1 4.927,4.104 6.865,4.333 1.938,0.229 10 false Front Passenger Side Air Mix*2 5.042,5.906 6.917,6.104 1.875,0.198 10 false Front Passenger Side Mode*1 5.292,6.229 6.823,6.438 1.531,0.208 10 false Driver Side Mode*2 5.281,7.979 6.646,8.385 1.365,0.406 10 false Front Passenger Side Air Mix*1 5.281,8.469 6.698,8.792 1.417,0.323 10 false Driver Side Air Mix*2 4.333,8.906 6.271,9.396 1.938,0.49 10 false No. 1 Air Conditioning Radiator Damper Servo Sub-assembly 1.865,7.552 3.406,8.031 1.542,0.479 10 false Air Conditioning Harness Assembly 0.302,6.979 1.844,7.458 1.542,0.479 10 false *1: for LHD 0.292,7.385 1.833,7.865 1.542,0.479 10 false *2: for RHD 3.479,4.771 3.969,5.021 0.49,0.25 10 false GND 3.49,5.146 3.979,5.396 0.49,0.25 10 false LIN 3.5,5.552 3.99,5.802 0.49,0.25 10 false +B 3.333,5.021 3.677,5.26 0.344,0.24 10 false 2 3.333,4.656 3.677,4.896 0.344,0.24 10 false 3 3.323,5.448 3.667,5.688 0.344,0.24 10 false 1


for Single Type


E334609E03
4.302,0.51 5.073,0.708 0.771,0.198 10 false BUS G 4.104,0.51 4.26,0.708 0.156,0.198 10 false 2 4.115,0.865 4.271,1.063 0.156,0.198 10 false 3 4.115,1.271 4.271,1.469 0.156,0.198 10 false 4 4.313,0.896 4.771,1.094 0.458,0.198 10 false BUS 4.323,1.292 5.094,1.49 0.771,0.198 10 false B BUS 3.969,1.948 6.271,2.302 2.302,0.354 10 false Air Conditioning Amplifier Assembly 6.083,4.344 6.813,4.729 0.729,0.385 10 false Air Mix 5.771,6.406 6.823,6.896 1.052,0.49 10 false Front Passenger Side Mode 0.052,1.771 1.969,2.229 1.917,0.458 10 false No. 2 Air Conditioning Radiator Damper Servo Sub-assembly 0.073,4.26 2,4.74 1.927,0.479 10 false No. 3 Air Conditioning Radiator Damper Servo Sub-assembly 4.51,7.656 6.438,8.208 1.927,0.552 10 false No. 1 Air Conditioning Radiator Damper Servo Sub-assembly 2.042,7.646 3.583,8.229 1.542,0.583 10 false Air Conditioning Harness Assembly 0.792,8.406 2.656,8.656 1.865,0.25 10 false : LIN Communication Line 5.375,1.323 5.688,1.521 0.313,0.198 10 false +B 5.458,0.969 5.771,1.167 0.313,0.198 10 false IC 3.74,4.104 3.896,4.302 0.156,0.198 10 false 3 3.885,4.219 4.344,4.417 0.458,0.198 10 false GND 3.729,4.438 3.885,4.635 0.156,0.198 10 false 2 3.896,5.021 4.208,5.219 0.313,0.198 10 false +B 3.719,4.896 3.875,5.094 0.156,0.198 10 false 1 3.906,4.635 4.365,4.833 0.458,0.198 10 false LIN 3.979,1.781 4.292,1.979 0.313,0.198 10 false z1


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.PERFORM ACTIVE TEST USING GTS

B

7.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix*1 or air mix*2) pulse Min.: 128
Max.: 383
Operates between 165 to 257 pulses
Air Outlet Servo Pulse (D) No. 2 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 164 to 256 pulses
A/O Servo Pulse(Rr D) No. 3 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 250 to 297 pulses

*1: for Dual Type

*2: for Single Type


Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Outlet Servo Pulse (D)
50004 121 26
Body Electrical > Air Conditioner > Active Test
Tester Display
A/O Servo Pulse(Rr D)
50004 121 56
OK:

Each damper servo motor operates smoothly.



Result:
Result Proceed to
All of the damper servo motors are malfunctioning A
Any of the damper servo motors is normal B



A

3.PERFORM ACTIVE TEST USING GTS

B

5.PERFORM ACTIVE TEST USING GTS
3.PERFORM ACTIVE TEST USING GTS
a.

Disconnect the No. 1 air conditioning radiator damper servo sub-assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Air Conditioner / Active test.


f.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
A/O Servo Pulse(Rr D) No. 3 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 250 to 297 pulses
Body Electrical > Air Conditioner > Active Test
Tester Display
A/O Servo Pulse(Rr D)
50004 121 56
OK:

The damper servo motor operates smoothly.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

4.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
4.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
NOTICE:

When inspecting the air conditioning amplifier assembly, do not bring the tester probes too close to each other as a short circuit may occur.


a.

Disconnect the z1 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (BUS G) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z1-4 (B BUS) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch on (IG).


e.
E334625C02
2.865,0.417 3.198,0.625 0.333,0.208 2.979,1.26 2.26,2.073 false 3.094,1.271 2.688,2.24 false 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 2.979,0.458 3.292,0.656 0.313,0.198 10 false z1 2.135,2.094 2.594,2.292 0.458,0.198 10 false BUS 2.49,2.271 2.948,2.51 0.458,0.24 10 false BUS G 0.417,3.938 0.875,4.135 0.458,0.198 10 false GND
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Connect an oscilloscope to terminals z1-2 (BUS G) and z1-3 (BUS) of the air conditioning amplifier assembly and check the waveform.

OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower speed.


Item Content
Tool Setting 2 V/DIV., 2 ms./DIV.
Vehicle Condition Power switch on (IG)


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING HARNESS ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

5.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix*1 or air mix*2) pulse Min.: 128
Max.: 383
Operates between 165 to 257 pulses
Air Outlet Servo Pulse (D) No. 2 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 164 to 256 pulses
A/O Servo Pulse(Rr D) No. 3 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 250 to 297 pulses

*1: for Dual Type

*2: for Single Type


Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Outlet Servo Pulse (D)
50004 121 26
Body Electrical > Air Conditioner > Active Test
Tester Display
A/O Servo Pulse(Rr D)
50004 121 56
OK:

Each damper servo motor operates smoothly.



Result:
Result Proceed to
Only the No. 1 air conditioning radiator damper servo sub-assembly does not operate A
Only the No. 2 air conditioning radiator damper servo sub-assembly does not operate B
Only the No. 3 air conditioning radiator damper servo sub-assembly does not operate
Only the No. 2 air conditioning radiator damper servo sub-assembly operates



A

6.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY)

B

REPLACE AIR CONDITIONING HARNESS ASSEMBLY

6.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY)
a.

Disconnect the z1 air conditioning amplifier assembly connector.


b.

Disconnect the No. 1 air conditioning radiator damper servo sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (BUS G) - 3 (GND) Always Below 1 Ω
z1-3 (BUS) - 1 (+B) Always Below 1 Ω
z1-4 (B BUS) - 2 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY

7.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix*1 or air mix*2) pulse Min.: 128
Max.: 383
Operates between 255 to 347 pulses
Air Outlet Servo Pulse (P) No. 2 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 164 to 256 pulses
A/O Servo Pulse(Rr D) No. 3 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 250 to 297 pulses

*1: for Dual Type

*2: for Single Type


Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Outlet Servo Pulse (P)
50004 121 97
Body Electrical > Air Conditioner > Active Test
Tester Display
A/O Servo Pulse(Rr D)
50004 121 56
OK:

Each damper servo motor operates smoothly.



Result:
Result Proceed to
All of the damper servo motors are malfunctioning A
Any of the damper servo motors is normal B



A

8.PERFORM ACTIVE TEST USING GTS

B

10.PERFORM ACTIVE TEST USING GTS
8.PERFORM ACTIVE TEST USING GTS
a.

Disconnect the No. 1 air conditioning radiator damper servo sub-assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Air Conditioner / Active test.


f.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
A/O Servo Pulse(Rr D) No. 3 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 250 to 297 pulses
Body Electrical > Air Conditioner > Active Test
Tester Display
A/O Servo Pulse(Rr D)
50004 121 56
OK:

The damper servo motor operates smoothly.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

9.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
9.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
NOTICE:

When inspecting the air conditioning amplifier assembly, do not bring the tester probes too close to each other as a short circuit may occur.


a.

Disconnect the z1 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (BUS G) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z1-4 (B BUS) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch on (IG).


e.
E334625C02
2.865,0.417 3.198,0.625 0.333,0.208 2.979,1.26 2.26,2.073 false 3.094,1.271 2.688,2.24 false 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 2.979,0.458 3.292,0.656 0.313,0.198 10 false z1 2.135,2.094 2.594,2.292 0.458,0.198 10 false BUS 2.49,2.271 2.948,2.51 0.458,0.24 10 false BUS G 0.417,3.938 0.875,4.135 0.458,0.198 10 false GND
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Connect an oscilloscope to terminals z1-2 (BUS G) and z1-3 (BUS) of the air conditioning amplifier assembly and check the waveform.

OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower speed.


Item Content
Tool Setting 2 V/DIV., 2 ms./DIV.
Vehicle Condition Power switch on (IG)


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING HARNESS ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

10.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix*1 or air mix*2) pulse Min.: 128
Max.: 383
Operates between 255 to 347 pulses
Air Outlet Servo Pulse (P) No. 2 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 164 to 256 pulses
A/O Servo Pulse(Rr D) No. 3 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 250 to 297 pulses

*1: for Dual Type

*2: for Single Type


Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Outlet Servo Pulse (P)
50004 121 97
Body Electrical > Air Conditioner > Active Test
Tester Display
A/O Servo Pulse(Rr D)
50004 121 56
OK:

Each damper servo motor operates smoothly.



Result:
Result Proceed to
Only the No. 1 air conditioning radiator damper servo sub-assembly does not operate A
Only the No. 2 air conditioning radiator damper servo sub-assembly does not operate B
Only the No. 3 air conditioning radiator damper servo sub-assembly does not operate
Only the No. 2 air conditioning radiator damper servo sub-assembly operates



A

11.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY)

B

REPLACE AIR CONDITIONING HARNESS ASSEMBLY

11.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY)
a.

Disconnect the z1 air conditioning amplifier assembly connector.


b.

Disconnect the No. 1 air conditioning radiator damper servo sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (BUS G) - 3 (GND) Always Below 1 Ω
z1-3 (BUS) - 1 (+B) Always Below 1 Ω
z1-4 (B BUS) - 2 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY