Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242209 MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM  P31241F  Lost Communication between Drive Motor "A" and HV ECU Circuit Intermittent  P312487  Lost Communication between Drive Motor "A" and HV ECU Missing Message  


DESCRIPTION

The motor generator control ECU, which is built into the inverter with converter assembly, controls the motor (MG2) based on commands from the hybrid vehicle control ECU.

The motor generator control ECU (MG ECU) monitors communication data and detects malfunctions.

A communication error between the motor generator control ECU and hybrid vehicle control ECU is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P31241F Lost Communication between Drive Motor "A" and HV ECU Circuit Intermittent Error in reception from hybrid vehicle control ECU via serial communication (out of communication standard) detected when DTC P0C7917, P0D3319, P1C5D19 or P1C5F19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Does not come on
P312487 Lost Communication between Drive Motor "A" and HV ECU Missing Message Error in reception from hybrid vehicle control ECU via serial communication (out of communication standard)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the Inverter Low-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Inverter Low-voltage Circuit

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Motor Generator / Trouble Codes.


e.

Clear the DTCs.

Powertrain > Motor Generator > Clear DTCs
50002 395

f.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

2.CHECK DIAGNOSIS RELATED INFORMATION AND DTC OUTPUT (MOTOR GENERATOR CONTROL)
2.CHECK DIAGNOSIS RELATED INFORMATION AND DTC OUTPUT (MOTOR GENERATOR CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Motor Generator / Utility / Diagnosis Related Information.

Powertrain > Motor Generator > Utility
Tester Display
Diagnosis Related Information
50005 395 56

d.

Enter the following menus: Powertrain / Motor Generator / Trouble Codes.

Powertrain > Motor Generator > Trouble Codes
50001 395

e.

Check for DTCs.

Result:
Result Proceed to
P31241F or P312487 is listed in Diagnosis Related Information or DTC P31241F or P312487 is output. A
P31241F and P312487 is not listed in Diagnosis Information and DTC P31241F and P312487 is not output. B



f.

Turn the power switch off.



A

3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

B

3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the following table.


b.

Turn the power switch on (IG).


c.
A369837C04
2.354,0.438 2.698,0.667 0.344,0.229 0.646,0.427 0.99,0.656 0.344,0.229 2.813,1.042 2.813,1.51 true 0.979,1.031 1.313,1.51 true 0.948,1.094 0.729,1.573 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.719,0.469 1.177,0.667 0.458,0.198 10 false A50 2.458,0.479 2.917,0.677 0.458,0.198 10 false F3 1.208,1.604 1.823,1.802 0.615,0.198 10 false HMCH 0.542,1.615 1.156,1.813 0.615,0.198 10 false HMCL 2.74,1.531 3.052,1.729 0.313,0.198 10 false E1 0.229,2.99 0.688,3.188 0.458,0.198 10 false CH1 0.24,3.76 0.698,3.958 0.458,0.198 10 false CH2 2.802,3.49 3.26,3.688 0.458,0.198 10 false GND 2.813,4.063 3.271,4.26 0.458,0.198 10 false GND
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the waveform.

Item Contents
Tester Connection CH1: A50-4 (HMCH) - F3-3 (E1)
CH2: A50-14 (HMCL) - F3-3 (E1)
Equipment Setting 1 V/DIV., 200 μs./DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


HINT:
·

Perform this inspection with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the power switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the C33 inverter with converter assembly connector.


c.

Disconnect the A50 hybrid vehicle control ECU connector.


d.
A367816C06
0.073,3.385 0.438,3.635 0.365,0.25 0.167,1.219 0.531,1.469 0.365,0.25 1.396,1.5 0.729,2.156 true 1.51,1.5 1.792,2.167 true 1.344,3.49 0.792,4.219 true 1.458,3.625 1.917,4.24 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.125,2.479 0.438,2.677 0.313,0.198 10 false *b 0.24,1.281 0.698,1.479 0.458,0.198 10 false C33 0.135,3.448 0.594,3.646 0.458,0.198 10 false A50 1.604,2.208 2.219,2.406 0.615,0.198 10 false HMCH 0.542,2.208 1.156,2.406 0.615,0.198 10 false HMCL 1.74,4.292 2.354,4.49 0.615,0.198 10 false HMCL 0.604,4.302 1.219,4.5 0.615,0.198 10 false HMCH
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C33-20 (HMCH) - A50-4 (HMCH) Power switch off Below 1 Ω
C33-19 (HMCL) - A50-14 (HMCL) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C33-20 (HMCH) or A50-4 (HMCH) - Body ground and other terminals Power switch off 10 kΩ or higher
C33-19 (HMCL) or A50-14 (HMCL) - Body ground and other terminals Power switch off 10 kΩ or higher



e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the power switch on (IG).


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C33-20 (HMCH) or A50-4 (HMCH) - Body ground and other terminals Power switch on (IG) Below 1 V
C33-19 (HMCL) or A50-14 (HMCL) - Body ground and other terminals Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU and inverter with converter assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the power switch off.


i.

Turn the power switch off.


j.

Reconnect the A50 hybrid vehicle control ECU connector.


k.

Reconnect the C33 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.
A365587C07
0.115,1 0.5,1.281 0.385,0.281 1.51,1.26 1.802,1.729 true 1.042,1.75 1.406,1.146 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.781,1.792 1.323,2 0.542,0.208 10 false HMCH 0.188,1.052 0.5,1.25 0.313,0.198 10 false A50 1.708,1.792 2.25,2 0.542,0.208 10 false HMCL
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-4 (HMCH) - A50-14 (HMCL) Power switch off 80 to 170 Ω



c.

Reconnect the A50 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY