Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › SIMPLE INTELLIGENT PARKING ASSIST SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0244874 SIMPLE INTELLIGENT PARKING ASSIST SYSTEM Y

PARK ASSIST / MONITORING  SIMPLE INTELLIGENT PARKING ASSIST SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the simple intelligent parking assist system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
·

When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B




A

5.PROBLEM SYMPTOM CONFIRMATION

B

5.PROBLEM SYMPTOM CONFIRMATION
Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT*
6.CHECK DTC OUTPUT*
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

b.

Recheck for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTCs are not output (Problem symptom occurs) A
DTCs are not output (Problem symptom does not occur) B
DTCs are output. C



A

7.DIAGNOSTIC TROUBLE CODE CHART

B

8.SYMPTOM SIMULATION

C

9.PROBLEM SYMPTOMS TABLE
7.DIAGNOSTIC TROUBLE CODE CHART
a.

Refer to Diagnostic Trouble Code Chart.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

NOTICE:

The clearance warning ECU assembly outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the TOYOTA parking assist-sensor system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.

System Proceed to
TOYOTA Parking Assist-sensor System (Click here)
Intelligent Clearance Sonar System (Click here)



Result:
Proceed to
NEXT



NEXT

11.CIRCUIT INSPECTION
8.SYMPTOM SIMULATION

Result:
Proceed to
NEXT



NEXT

9.PROBLEM SYMPTOMS TABLE
9.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

10.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

11.CIRCUIT INSPECTION
11.CIRCUIT INSPECTION
Result:
Proceed to
NEXT



NEXT

12.IDENTIFICATION OF PROBLEM
12.IDENTIFICATION OF PROBLEM
Result:
Proceed to
NEXT



NEXT

13.REPAIR OR REPLACE
13.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

14.CONFIRMATION TEST
14.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END