Home › Power Source / Network › 2ZR-FXE BATTERY / CHARGING › CHARGING SYSTEM
RM3210E _57 Power Source / Network _047502 2ZR-FXE BATTERY / CHARGING _0244883 CHARGING SYSTEM C

2ZR-FXE BATTERY / CHARGING  CHARGING SYSTEM  P058A01  Auxiliary Battery Monitor Module Range/Performance  


DESCRIPTION

The battery state sensor assembly detects the auxiliary voltage, current and temperature of the auxiliary battery. The battery state sensor assembly calculates State of Charge (SOC) based on the voltage and current of the auxiliary battery and sends it to the hybrid vehicle control ECU. Based on the signals received, the hybrid vehicle control ECU adjusts the charging voltage of the DC/DC converter.

The battery state sensor assembly calculates the auxiliary battery temperature based on changes in resistance of a built-in thermistor and sends it to the hybrid vehicle control ECU. The hybrid vehicle control ECU reduces the amount of charging current based on this signal in order to protect the auxiliary battery.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P058A01 Auxiliary Battery Monitor Module Range/Performance Any of the following conditions is met with the power switch on (IG). (1 trip detection logic):
·

Current is 999.939 A or more, or -1000 A or less for 3.2 seconds or more.

·

The difference between the maximum and minimum current is 0.0305 A or less for 100 seconds or more.

·

A current detection circuit malfunction signal is received.

·

The auxiliary battery temperature is 105°C (221°F) or more or -40°C (-40°F) or less for 3.2 seconds or more.

·

A temperature detection circuit malfunction signal is received.

·

Voltage is 15.98 V or more, or 6.0 V or less for 3.2 seconds or more.

·

A voltage detection circuit malfunction signal is received.

·

A writing error occurs in the auxiliary battery state sensor internal memory (battery identification data).


·

Battery state sensor assembly

·

Auxiliary battery

·

Wire harness or connector


Charge warning light does not come on DTC stored

WIRING DIAGRAM

A331074E19
5.198,3.042 6.885,3.396 1.688,0.354 10 false Hybrid Vehicle Control ECU 5.208,2.875 5.667,3.073 0.458,0.198 10 false A50 5.5,0.635 5.958,0.833 0.458,0.198 10 false LIN3 5.271,0.479 5.729,0.677 0.458,0.198 10 false 8 4.063,0.646 4.521,0.844 0.458,0.198 10 false LIN 4.427,0.479 4.885,0.677 0.458,0.198 10 false 2 2.99,0.646 3.448,0.844 0.458,0.198 10 false +B 2.781,0.531 3.24,0.729 0.458,0.198 10 false 1 1.479,0.802 2.333,1.156 0.854,0.354 10 false BATT-S 0.927,2.302 2.01,2.635 1.083,0.333 10 false Auxiliary Battery 2.823,1.333 4.771,1.792 1.948,0.458 10 false Battery State Sensor Assembly 2.833,1.167 3.292,1.365 0.458,0.198 10 false C19 0.792,3.292 2.365,3.594 1.573,0.302 10 false : LIN Communication Line 0.74,1.354 1.594,1.708 0.854,0.354 10 false BATT-MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When P162B87 (Lost Communication with Battery Monitor Module Missing Message) is output at the same time, perform troubleshooting for P162B87 (Lost Communication with Battery Monitor Module Missing Message) first.



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION
a.

Check installation condition of the battery state sensor assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the C19 battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



d.
A331105C66
1.521,0.135 1.927,0.375 0.406,0.24 0.667,1.667 0.667,1.5 0.667,1.5 1.542,1.167 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.573,1.708 1.01,1.927 0.438,0.219 10 false +B 1.604,0.177 2.063,0.375 0.458,0.198 10 false C19
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C19-1 (+B) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR