Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0244900 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the steering pad switch assembly (distance control switch) while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

A303849E46
1.229,0.99 2.813,1.208 1.583,0.219 10 false Distance Control Switch 0.938,2.615 3.021,3.479 2.083,0.865 10 false Steering Pad Switch Assembly 3.208,2.552 4.271,3.219 1.063,0.667 10 false Spiral Cable with Sensor Sub-assembly 5.594,2.406 5.906,2.604 0.313,0.198 10 false F40 5.594,2.563 6.615,3.417 1.021,0.854 10 false Driving Support ECU Assembly 2.542,0.75 3.156,0.948 0.615,0.198 10 false DIST 3.365,0.74 3.979,0.938 0.615,0.198 10 false DIST 3.813,0.74 4.427,0.938 0.615,0.198 10 false DIST 2.521,1.906 2.979,2.104 0.458,0.198 10 false ECC 3.365,1.906 3.823,2.104 0.458,0.198 10 false ECC 3.833,1.906 4.292,2.104 0.458,0.198 10 false ECC 3.031,0.844 3.344,1.042 0.313,0.198 10 false z3 3.042,2 3.354,2.198 0.313,0.198 10 false z3 4.219,2 4.677,2.198 0.458,0.198 10 false F21 4.219,0.854 4.677,1.052 0.458,0.198 10 false F21 5.719,0.865 6.333,1.063 0.615,0.198 10 false SPSW 5.479,0.75 5.719,0.948 0.24,0.198 10 false 23 4.26,0.635 4.573,0.833 0.313,0.198 10 false 12 4.292,1.792 4.448,1.99 0.156,0.198 10 false 2 3.063,0.635 3.219,0.833 0.156,0.198 10 false 4 3.063,1.792 3.219,1.958 0.156,0.167 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.READ VALUE USING GTS (DISTANCE CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Distance Control Switch Distance control switch signal ON or OFF ON: Distance control switch on
OFF: Distance control switch off
-
Powertrain > Radar Cruise2 > Data List
Tester Display
Distance Control Switch
50003 197 5
OK:

The Data List item shown in the table changes according to the operation of the steering pad switch assembly (distance control switch).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the F21 spiral cable with sensor sub-assembly connector.


b.

Disconnect the F40 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-12 (DIST) - F40-23 (SPSW) Always Below 1 Ω
F21-2 (ECC) - Body ground Always Below 1 Ω
F21-12 (DIST) or F40-23 (SPSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR