Home › Engine / Hybrid System › 2ZR-FXE ENGINE MECHANICAL › ENGINE UNIT
RM3210E _51 Engine / Hybrid System _047495 2ZR-FXE ENGINE MECHANICAL _0244907 ENGINE UNIT A

2ZR-FXE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 11420 1.INSTALL STIFFENING CRANKCASE ASSEMBLY

NOTICE:

It is not necessary to remove ring pins unless they are being replaced.


a.
A374143C01
3.031,2.469 3.344,2.625 0.313,0.156 10 false *a 0.719,2.125 1.031,2.281 0.313,0.156 10 false *b 1.354,2.75 1.667,2.906 0.313,0.156 10 false *c
*a Protrusion Height
*b 11 mm
*c 8 mm


Using a plastic hammer, tap 2 new ring pins into the stiffening crankcase assembly.

Standard Ring Pin:
Item Protrusion Height Height Width
Ring pin 4.0 mm (0.157 in.) 8.0 mm (0.315 in.) 11 mm (0.433 in.)



b.
A374474N01
0.656,2.677 0.813,2.875 0.156,0.198 10 false A

Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three bond 1207B or equivalent


Standard Seal Packing Diameter:
Area Specified Condition
Continuous Line 2.0 to 3.0 mm (0.0787 to 0.118 in.)
(A) 4.5 to 5.5 mm (0.177 to 0.217 in.)


Application Length (A):

56 mm (2.20 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installing the stiffening crankcase assembly.




c.
A374475N01
3.135,0.719 3.292,0.917 0.156,0.198 10 false A 3.135,1.573 3.292,1.771 0.156,0.198 10 false A 0.896,0.125 1.052,0.323 0.156,0.198 10 false B 1.406,0.115 1.563,0.313 0.156,0.198 10 false B 1.708,0.167 1.865,0.365 0.156,0.198 10 false B 2.188,0.25 2.344,0.448 0.156,0.198 10 false C 0.719,2.198 0.875,2.396 0.156,0.198 10 false C 1.073,2.177 1.229,2.375 0.156,0.198 10 false C 1.417,2.188 1.573,2.385 0.156,0.198 10 false C 1.844,2.135 2,2.333 0.156,0.198 10 false C 2.354,2.135 2.51,2.333 0.156,0.198 10 false C 0.896,2.448 1.052,2.646 0.156,0.198 10 false 8 1.406,2.438 1.563,2.635 0.156,0.198 10 false 4 1.708,2.49 1.865,2.688 0.156,0.198 10 false 2 2.198,2.552 2.354,2.75 0.156,0.198 10 false 6 3.135,3.052 3.292,3.25 0.156,0.198 10 false 9 3.115,3.906 3.333,4.156 0.219,0.25 10 false 11 2.365,4.469 2.521,4.667 0.156,0.198 10 false 7 1.865,4.469 2.021,4.667 0.156,0.198 10 false 3 1.323,4.469 1.479,4.667 0.156,0.198 10 false 1 1.042,4.469 1.198,4.667 0.156,0.198 10 false 5 0.563,4.417 0.781,4.667 0.219,0.25 10 false 10

Install the stiffening crankcase assembly with the 11 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Bolt Length:
Item Specified Condition
Bolt (A) 138 mm (5.43 in.)
Bolt (B) 35 mm (1.38 in.)
Bolt (C) 70 mm (2.76 in.)



d.

Recheck the torque for the bolts (1) and (2).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.

Wipe off any excess seal packing with a clean piece of cloth.


Hide 15100 2.INSTALL OIL PUMP ASSEMBLY

NOTICE:

It is not necessary to remove ring pins unless they are being replaced.


a.
A374476C01
2.927,2.448 3.24,2.604 0.313,0.156 10 false *a 0.646,2.135 0.958,2.292 0.313,0.156 10 false *b 1.25,2.74 1.563,2.896 0.313,0.156 10 false *c
*a Protrusion Height
*b 11 mm
*c 8 mm


Using a plastic hammer, tap 2 new ring pins into the stiffening crankcase assembly.

Standard Ring Pin:
Item Protrusion Height Height Width
Ring pin 3.0 mm (0.118 in.) 8.0 mm (0.315 in.) 11 mm (0.433 in.)



b.

Install the oil pump assembly.

Click hereEngine / Hybrid System>2ZR-FXE LUBRICATION>OIL PUMP>INSTALLATION


Hide 89491 3.INSTALL ENGINE OIL LEVEL SENSOR

Hide 12102A 4.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A374478C01
1.625,2.552 1.938,2.708 0.313,0.156 10 false *a 2.281,2.729 2.594,2.885 0.313,0.156 10 false *b 1.635,2.906 1.948,3.063 0.313,0.156 10 false *a
*a 9 mm (0.354 in.)
*b 19 mm (0.748 in.)


Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Remove any remaining seal packing.

NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installing the No. 2 oil pan sub-assembly.

·

Keep the contact surfaces of the stiffening crankcase assembly and No. 2 oil pan sub-assembly free of oil.




c.
A377996C01
2.75,2.073 2.552,1.781 true 0.271,1.344 0.427,1.542 0.156,0.198 10 false A 0.906,1.344 1.063,1.542 0.156,0.198 10 true A 0.292,0.938 0.448,1.135 0.156,0.198 10 false B 0.906,0.938 1.073,1.104 0.167,0.167 10 true B 1.021,2.354 1.792,2.552 0.771,0.198 10 false A - A 2.177,2.354 2.948,2.552 0.771,0.198 10 false B - B 2.74,2.125 3.052,2.323 0.313,0.198 10 false *a 0.729,2.573 1.042,2.771 0.313,0.198 10 false *b 2.604,2.542 2.917,2.74 0.313,0.198 10 false *c
*a Seal Packing
*b 6.0 mm
*c 3.0 to 4.5 mm


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Application Specification:
Area Seal Packing Diameter Distance from Center of Bolt Hole to Center of Seal Packing
(A) - (A) 3.0 to 4.5 mm (0.118 to 0.177 in.) 6.0 mm (0.236 in.)
(B) - (B) -



d.
A374142C01
2.177,1.802 2.49,1.958 0.313,0.156 10 false *a 0.208,1.656 0.521,1.813 0.313,0.156 10 false *a
*a Nut


Install the No. 2 oil pan sub-assembly to the stiffening crankcase assembly with the 10 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101A 5.INSTALL OIL PAN DRAIN PLUG

a.
A374141

Install a new gasket and oil pan drain plug to the No. 2 oil pan sub-assembly.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 12204 7.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 11101 9.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head set bolts are tightened in 3 progressive steps.


a.

Clean the cylinder block sub-assembly and cylinder head sub-assembly with solvent.


b.

Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:
·

Remove any oil from the contact surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the gasket with the bottom of the cylinder head sub-assembly.




c.

Install the 10 cylinder head set plate washers to the 10 cylinder head set bolts.


d.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


e.

Step 1:

i.
A374456N02
0.708,1.813 0.958,2.042 0.25,0.229 10 true 10 0.698,0.271 0.854,0.469 0.156,0.198 10 true 8 1.177,0.271 1.333,0.469 0.156,0.198 10 true 4 1.188,1.802 1.344,2 0.156,0.198 10 true 6 1.677,0.281 1.833,0.479 0.156,0.198 10 true 2 1.646,1.802 1.896,2.042 0.25,0.24 10 true 1 2.146,0.26 2.302,0.458 0.156,0.198 10 true 5 2.146,1.802 2.302,2 0.156,0.198 10 true 3 2.646,0.26 2.802,0.458 0.156,0.198 10 true 9 2.635,1.781 2.792,1.979 0.156,0.198 10 true 7

Using a 10 mm bi-hexagon socket wrench, install and uniformly tighten the 10 cylinder head set bolts in several steps in the order shown in the illustration.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Do not drop the cylinder head set plate washers for the cylinder head set bolts into the cylinder head sub-assembly.




f.
A377997C02
1.49,1.531 1.635,1.531 1.635,1.531 1.906,1.115 true 1.458,0.396 1.771,0.594 0.313,0.198 10 false 90° 2.542,0.125 2.854,0.323 0.313,0.198 10 false 45° 1.281,1.469 1.594,1.667 0.313,0.198 10 false *a
*a Paint Mark
V100135

Front of Engine


Step 2:

i.

Mark each cylinder head set bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head set bolts 90° in the order shown in step 1.



g.

Step 3:

i.

Tighten the cylinder head set bolts another 45° in the order shown in step 1.



h.

Check that the paint marks are now at a 135° angle.

NOTICE:

Do not add engine oil for at least 2 hours after installing the cylinder head sub-assembly.



i.
A374487C02
0.677,2.177 0.99,2.333 0.313,0.156 10 false *a 2.313,2.177 2.625,2.333 0.313,0.156 10 false *b
*a Before Wiping Off
*b After Wiping Off


After tightening the cylinder head set bolts, wipe off any seal packing that seeped out from the contact surfaces between the cylinder head sub-assembly and cylinder block sub-assembly.

NOTICE:
·

Be sure to wipe off the seal packing from inside to outside, parallel to the joint line.

·

Be sure to avoid clogging the bolt holes when wiping off the seal packing.




Hide 13716 10.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem ends.


b.
A377940

Install the 16 valve stem caps to the cylinder head sub-assembly.

NOTICE:
·

Install each part to its original location.

·

Do not drop the valve stem caps into the cylinder head sub-assembly.




Hide 13750 11.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect the 16 valve lash adjuster assemblies before installing them.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION


b.
A377939

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install each part to its original location.



Hide 13801 12.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A377998C01
0.719,1.313 1.146,1.313 false 1.208,0.396 1.635,0.396 false 2.156,0.729 2.583,0.729 false 0.531,1.229 0.844,1.427 0.313,0.198 10 false *1 1.021,0.313 1.333,0.51 0.313,0.198 10 false *2 2.646,0.656 2.958,0.854 0.313,0.198 10 false *3
*1 Valve Lash Adjuster Assembly
*2 No. 1 Valve Rocker Arm Sub-assembly
*3 Valve Stem Cap


Apply engine oil to the tips of the valve lash adjuster assemblies and valve stem caps.


b.

Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.

NOTICE:

Install each part to its original location.



Hide 13.INSTALL RING PIN

NOTICE:

It is not necessary to remove ring pins unless they are being replaced.


a.
A374482C01
3.052,2.458 3.365,2.615 0.313,0.156 10 false *a 0.719,2.146 1.031,2.302 0.313,0.156 10 false *b 1.344,2.74 1.656,2.896 0.313,0.156 10 false *c
*a Protrusion Height
*b 20 mm
*c 13 mm


Using a plastic hammer, tap 10 new ring pins into the camshaft housing sub-assembly.

Standard Ring Pin:
Item Protrusion Height Height Width
Ring pin 3.0 mm (0.118 in.) 13 mm (0.512 in.) 20 mm (0.787 in.)



Hide 11811 14.INSTALL NO. 1 CAMSHAFT BEARING

a.

Clean both surfaces of the No. 1 camshaft bearings.


b.

Install the 2 No. 1 camshaft bearings.


c.
A377999C01
0.448,2.938 0.448,2.135 0.448,2.135 0.615,2.135 false 0.542,2.635 0.698,2.833 0.156,0.198 10 false A 2.396,2.646 2.552,2.844 0.156,0.198 10 true B 0.677,2.031 0.99,2.229 0.313,0.198 10 false *a
*a Vernier Caliper


Using a vernier caliper, measure the distance between the No. 1 camshaft bearing cap edge and the No. 1 camshaft bearing edge.

Standard Dimension (A) - (B):

0.7 mm (0.0276 in.) or less


NOTICE:

Position the No. 1 camshaft bearings to the center of the camshaft bearing cap by measuring dimensions (A) and (B).



Hide 11821 15.INSTALL NO. 2 CAMSHAFT BEARING

a.

Clean both surfaces of the No. 2 camshaft bearings.


b.

Install the 2 No. 2 camshaft bearings.


c.
A374490C01
1.26,4.083 1.26,3.781 false 1.281,3.281 1.438,3.479 0.156,0.198 10 false A 1.188,4.104 1.5,4.302 0.313,0.198 10 false *a
*a Vernier Caliper


Using a vernier caliper, measure the distance between the camshaft housing sub-assembly edge and the No. 2 camshaft bearing edge.

Dimension (A):

1.05 to 1.75 mm (0.0413 to 0.0689 in.)


NOTICE:

Position the No. 2 camshaft bearings to the center of the camshaft housing sub-assembly by measuring dimension (A).



Hide 15678A 16.INSTALL OIL CONTROL VALVE FILTER

a.
A377531

Check that no foreign matter is on the mesh of the oil control valve filter.


b.

Install the oil control valve filter.

NOTICE:

Do not touch the mesh when installing the oil control valve filter.



Hide 13511 18.INSTALL CAMSHAFT

HINT:

Perform Inspection After Repair after replacing the camshaft.



a.

Clean the camshaft journals.


b.

Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


c.
A374492

Install the camshaft to the camshaft housing sub-assembly.


Hide 19.INSTALL CAMSHAFT BEARING CAP

a.
A374493C02
0.979,2.542 1.271,2.292 1.271,2.292 1.396,2.292 false 2.448,2.542 2.448,2.198 2.448,2.198 2.604,2.198 false 1.469,2.208 1.781,2.365 0.313,0.156 10 false *a 2.74,2.458 3.198,2.656 0.458,0.198 10 false 50° 2.656,2.115 2.969,2.271 0.313,0.156 10 false *a
*a Knock Pin


Confirm the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.


b.
A374494N01
0.229,0.458 0.542,0.656 0.313,0.198 10 false 10 0.229,1.521 0.385,1.719 0.156,0.198 10 false 9 0.771,0.344 0.927,0.542 0.156,0.198 10 true 6 0.719,1.563 0.875,1.76 0.156,0.198 10 true 5 1.292,0.354 1.448,0.552 0.156,0.198 10 true 2 1.917,1.583 2.073,1.781 0.156,0.198 10 true 1 2.448,0.521 2.604,0.719 0.156,0.198 10 true 4 2.427,1.531 2.583,1.729 0.156,0.198 10 true 3 2.938,0.531 3.094,0.729 0.156,0.198 10 true 8 2.896,1.594 3.052,1.792 0.156,0.198 10 true 7

Tighten the 10 bearing cap bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 13801 20.SET NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A379567C01
0.448,0.813 0.656,0.813 false 1.177,1.469 1.344,1.469 false 2.854,1.49 3.021,1.49 false 1.125,0.677 1.292,0.677 false 2.167,0.76 2.375,0.76 false 2.927,0.656 3.135,0.656 false 1.333,0.594 1.646,0.792 0.313,0.198 10 false *1 3.167,0.563 3.375,0.781 0.208,0.219 10 false *1 1.406,1.365 1.719,1.563 0.313,0.198 10 false *2 3.083,1.427 3.396,1.625 0.313,0.198 10 false *2 1.99,0.667 2.302,0.865 0.313,0.198 10 false *3 0.281,0.719 0.594,0.917 0.313,0.198 10 false *3 0.833,0.167 1.146,0.365 0.313,0.198 10 false *a 2.75,0.177 3.063,0.375 0.313,0.198 10 false *b
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap
*a Correct
*b Incorrect


Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


Hide 11103 21.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A374496C01
1.396,1.052 1.813,0.635 true 1.677,2.813 1.469,2.396 true 0.271,0.458 0.583,0.615 0.313,0.156 10 false *a 1.802,0.479 2.115,0.635 0.313,0.156 10 false *b 1.646,2.865 1.958,3.021 0.313,0.156 10 false *c
*a Cylinder Head Sub-assembly Upper Side
*b Seal Packing
*c 3.5 to 4.0 mm (0.138 to 0.157 in.)


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.
A374497C01
1.281,1.948 1.438,2.146 0.156,0.198 10 true 1 1.635,1.354 1.792,1.552 0.156,0.198 10 false 2 1.656,3.229 1.813,3.427 0.156,0.198 10 false 3 1.854,1.906 2.01,2.104 0.156,0.198 10 true 4 2.26,1.365 2.417,1.563 0.156,0.198 10 false 5 2.292,3.198 2.448,3.396 0.156,0.198 10 false 6 1.104,3.208 1.26,3.406 0.156,0.198 10 false 9 1.177,1.365 1.333,1.563 0.156,0.198 10 false 8 0.792,1.958 0.948,2.156 0.156,0.198 10 true 7 0.771,1.219 1.146,1.531 0.375,0.313 10 false 17 0.396,1.323 0.771,1.635 0.375,0.313 10 false 14 0.167,2.156 0.542,2.469 0.375,0.313 10 false 13 0.427,3.26 0.802,3.573 0.375,0.313 10 false 15 2.76,3.188 3.135,3.5 0.375,0.313 10 false 12 2.344,1.875 2.552,2.094 0.208,0.219 10 true 10 2.865,1.417 3.24,1.729 0.375,0.313 10 false 11 3.208,2.229 3.427,2.458 0.219,0.229 10 false 16
V100135

Bolt (A)
V100136

Bolt (B)


Set the camshaft and No. 2 camshaft as shown in the illustration.


c.

Install the camshaft housing sub-assembly with the 17 bolts and tighten them in the order shown in the illustration.

Torque:
Bolt (A) : 27 N*m (275 kgf*cm, 20 ft.*lbf)
Bolt (B) : 16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:
·

After installing the camshaft housing sub-assembly, make sure that the cam lobes are positioned as shown in the illustration.

·

If it is necessary to loosen any of the bolts during installation, remove the camshaft housing sub-assembly, clean the installation surfaces, and reapply seal packing.

·

If it is necessary to remove the camshaft housing sub-assembly during installation, make sure that the previously applied seal packing does not enter any oil passages.

·

After installing the camshaft housing sub-assembly, wipe off any seal packing that seeped out from between the camshaft housing sub-assembly and cylinder head sub-assembly.




Hide 22.INSTALL CAMSHAFT TIMING SPROCKET

a.
A374445

Using a wrench to hold the hexagonal portion of the No. 2 camshaft, tighten the bolt.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 13050 23.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.
A374499C01
2.167,0.948 2.458,1.615 true 1.052,0.885 1.677,0.406 true 2.438,1.635 2.75,1.792 0.313,0.156 10 false *a 1.719,0.333 2.031,0.49 0.313,0.156 10 false *b
*a Knock Pin
*b Key Groove


Align and fit the knock pin of the camshaft to the knock pin hole of the camshaft timing gear assembly.


b.
A374501C01
1.104,2.292 0.615,1.854 0.615,1.854 1.083,1.49 false 1.427,2.438 2.313,1.698 2.313,1.698 1.417,1.344 false 0.417,1.792 0.729,1.948 0.313,0.156 10 false *1 2.375,1.615 2.688,1.771 0.313,0.156 10 false *a 1.313,1.781 1.625,1.938 0.313,0.156 10 false *b
*1 Camshaft Timing Gear Assembly
*a Camshaft Flange
*b No Gap


Check that there is no gap between the camshaft timing gear assembly and camshaft flange.


c.
A374444

Using a wrench to hold the hexagonal portion of the camshaft, tighten the bolt.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


d.
A374503C01
0,0 0,0 false
V100135

Lock


Check that the camshaft timing gear assembly can move in the retard direction (clockwise) and locks in the most retarded position.


Hide 13521A 24.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A378000

Using a plastic hammer, tap in the 2 crankshaft timing gear keys.

HINT:

Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.



Hide 19315 25.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A374147

Install the No. 1 crankshaft position sensor plate to the crankshaft with the "F" mark facing forward.


Hide 13507 26.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

a.

Temporarily install the crankshaft pulley set bolt to the crankshaft.


b.
A374156C01
2.708,0.74 2.844,0.583 true 2.583,0.76 2.896,0.958 0.313,0.198 10 true *1
*1 Crankshaft Timing Gear Key


Set the crankshaft timing gear keys as shown in the illustration.


c.

Turn the oil pump drive shaft so that the flat face is facing upward.


d.

Remove the crankshaft pulley set bolt from the crankshaft.


e.
A378001C01
2.146,1.698 1.948,1.698 1.948,1.698 1.365,1.792 false 2.146,2.177 1.979,2.177 1.979,2.177 1.302,1.938 false 2.26,2.792 2.094,2.792 2.094,2.792 1.417,2.552 false 2.656,3.271 2.49,3.271 2.49,3.271 1.792,3.604 false 2.667,3.875 2.5,3.875 2.5,3.875 1.802,4.208 false 2.656,4.49 2.5,4.49 2.5,4.49 1.802,4.375 false 2.219,1.625 2.531,1.823 0.313,0.198 10 false *a 2.208,2.104 2.521,2.302 0.313,0.198 10 false *b 2.333,2.708 2.646,2.906 0.313,0.198 10 false *1 2.719,3.198 3.031,3.396 0.313,0.198 10 false *2 2.74,3.813 3.052,4.01 0.313,0.198 10 false *b 2.719,4.417 3.031,4.615 0.313,0.198 10 false *a
*1 Oil Pump Drive Gear
*2 Oil Pump Drive Shaft Gear
*a Mark Plate (Yellow)
*b Timing Mark
V100135

Front of Engine


Align the mark plates (yellow) with the timing mark of the oil pump drive gear and oil pump drive shaft gear as shown in the illustration.

HINT:

Make sure the mark plates (yellow) of the No. 2 chain sub-assembly are facing away from the engine assembly.



f.

With the No. 2 chain sub-assembly placed around the oil pump drive gear and oil pump drive shaft gear, install the oil pump drive gear to the crankshaft and temporarily install the oil pump drive shaft gear to the oil pump drive shaft.


g.

Temporarily install the oil pump drive shaft gear nut.


h.
A374504C01
0.573,1.438 1.229,1.438 false 1.042,1.198 1.698,1.198 true 0.354,1.385 0.667,1.542 0.313,0.156 10 false *1 0.844,1.135 1.156,1.292 0.313,0.156 10 false *2
*1 Chain Tensioner Plate
*2 Chain Damper Spring


Install the chain damper spring to the chain tensioner plate, and then install the chain tensioner plate with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


i.

Temporarily install the crankshaft pulley to the crankshaft with the crankshaft pulley set bolt.


j.
A374505N01
0.938,1.021 0.469,1.542 0.469,1.542 1.771,1.573 true 0.49,1.531 1.156,1.396 true 0.177,1.49 0.635,1.688 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley and tighten the oil pump drive shaft gear nut.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


k.

Remove SST, the crankshaft pulley set bolt and crankshaft pulley.


Hide 13521 27.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A374506

Install the crankshaft timing sprocket to the crankshaft.


Hide 28.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.

Temporarily install the crankshaft pulley set bolt to the crankshaft.


b.
A374157C01
1.792,0.958 2.396,0.958 true 2.458,0.896 2.771,1.052 0.313,0.156 10 true *1
*1 Crankshaft Timing Gear Key


Turn the crankshaft clockwise until the crankshaft timing gear key is facing upward.


c.
A374158C01
1.563,1.292 2.198,0.604 true 0.521,1.229 1.177,0.427 true 0.313,1.458 0.313,1.708 0.313,1.708 0.906,1.708 true 0.781,1.427 0.781,1.698 true 2.229,0.479 2.542,0.635 0.313,0.156 10 false *a 1.208,0.281 1.521,0.438 0.313,0.156 10 false *b 0.938,1.635 1.25,1.792 0.313,0.156 10 true *c
*a Timing Mark
*b Timing Mark (Rectangle)
*c Mark (Circle)


Check that the timing marks on the camshaft timing gear assembly and camshaft timing sprocket are aligned as shown in the illustration.

HINT:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.



d.

Remove the crankshaft pulley set bolt from the crankshaft.


Hide 13562 30.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.
A374438

Install the No. 2 chain vibration damper to the camshaft housing sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13559 31.INSTALL CHAIN TENSIONER SLIPPER

a.
A374139

Install the chain tensioner slipper to the cylinder block sub-assembly.


Hide 15609D 32.INSTALL OIL FILTER BRACKET WITH HEAD STRAIGHT SCREW PLUG

a.
A374518

Using a 10 mm hexagon socket wrench, install 2 new gaskets and the 2 oil filter bracket with head straight screw plugs to the oil filter bracket.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 11302 33.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

NOTICE:

If the stud bolts are deformed or the threads are damaged, replace them.


a.

Type A:

i.
A374516C01
1.938,2.594 2.25,2.75 0.313,0.156 10 false *a 1.948,3.125 2.26,3.281 0.313,0.156 10 false *b 2.385,2.833 2.698,2.99 0.313,0.156 10 false *c
*a 21 mm (0.827 in.)
*b 9 mm (0.354 in.)
*c 34 mm (1.34 in.)


Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



b.
A374481

Install the 2 stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Remove any remaining seal packing.


d.
A374436

Install a new gasket to the engine water pump assembly.

HINT:

Be sure to clean the contact surfaces.



e.
A374435

Install the engine water pump assembly to the timing chain cover sub-assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.

Clean the contact surfaces of the timing chain cover sub-assembly, camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.

A374520C01
1.167,0.333 1.479,0.49 0.313,0.156 10 false *a 4.323,0.365 4.635,0.521 0.313,0.156 10 false *b
*a Cylinder Head Sub-assembly and Cylinder Block Sub-assembly Side *b Timing Chain Cover Sub-assembly Side
V100145

Clean and degrease - -



g.
A214924

Install 3 new O-rings to the cylinder head sub-assembly and cylinder block sub-assembly.


h.
A374522

Apply seal packing to the engine unit as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Diameter:

5.0 mm (0.197 in.)


NOTICE:

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.



i.

Apply seal packing to the timing chain cover sub-assembly in a continuous line as shown in the illustration.

A374523C02
2.292,2.177 2.781,1.906 true 4.604,1.958 5.031,2.26 true 1.583,5.479 1.833,5.865 true 3.615,5.438 4.01,5.74 true 5.604,5.49 6,5.792 true 2.323,1.146 2.479,1.344 0.156,0.198 10 false A 3.052,0.802 3.208,1 0.156,0.198 10 true A 1.875,1.427 2.031,1.625 0.156,0.198 10 false F 1.521,2.031 1.677,2.229 0.156,0.198 10 false G 1.146,2.292 1.302,2.49 0.156,0.198 10 false H 2.146,2.167 2.302,2.365 0.156,0.198 10 false D 2.427,2.344 2.583,2.542 0.156,0.198 10 false O 5.01,1.333 5.167,1.531 0.156,0.198 10 false J 5.083,2.271 5.24,2.469 0.156,0.198 10 false E 5.375,2 5.531,2.198 0.156,0.198 10 false K 5.74,2.229 5.896,2.427 0.156,0.198 10 false L 6.094,2.271 6.25,2.469 0.156,0.198 10 false M 6.469,4.063 6.625,4.26 0.156,0.198 10 false N 0.75,4.031 0.906,4.229 0.156,0.198 10 false I 1.521,5.063 1.833,5.219 0.313,0.156 10 false *a 3.49,5.01 3.802,5.167 0.313,0.156 10 false *b 5.448,5.042 5.76,5.198 0.313,0.156 10 false *c 6.042,5.75 6.354,5.906 0.313,0.156 10 false *f 4.052,5.708 4.365,5.865 0.313,0.156 10 false *e 1.885,5.833 2.198,5.99 0.313,0.156 10 false *d 1.219,6.583 1.375,6.781 0.156,0.198 10 false D 4.688,6.552 4.844,6.75 0.156,0.198 10 false E 1.646,7.594 1.802,7.792 0.156,0.198 10 false B 2.417,7.146 2.573,7.344 0.156,0.198 10 false B 5.083,7.323 5.24,7.521 0.156,0.198 10 false B 5.854,7.594 6.01,7.792 0.156,0.198 10 false B 4.906,8.292 5.063,8.49 0.156,0.198 10 false B 5.615,8.667 5.771,8.865 0.156,0.198 10 false B 5.167,7.99 5.323,8.188 0.156,0.198 10 false C 5.854,8.073 6.01,8.271 0.156,0.198 10 false C 1.646,8.021 1.802,8.219 0.156,0.198 10 false C 2.427,8.01 2.583,8.208 0.156,0.198 10 false C 1.375,4.833 2.146,5.031 0.771,0.198 10 false A - A 3.417,4.844 4.188,5.042 0.771,0.198 10 false B - B 5.385,4.813 6.156,5.01 0.771,0.198 10 false C - C
*a 2.5 mm *b 5.0 mm
*c 7.5 mm *d 2.5 to 3.5 mm
*e 4.5 to 5.5 mm *f 7.0 to 8.0 mm


Seal Packing:
Item Seal Packing
Dashed line Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Continuous line
Alternate long and short dashed line Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Application Specification:
Area Seal Packing Diameter Distance from Edge of Cover to: Seal Packing Application Length Distance from Top of Cover to Top of Seal Packing
Dashed line 2.5 to 3.5 mm (0.0984 to 0.138 in.) Center of seal packing
2.5 mm (0.0984 in.)
- -
Continuous line 4.5 to 5.5 mm (0.177 to 0.217 in.) or 7.0 to 8.0 mm (0.276 to 0.315 in.) - - -
Alternate long and short dashed line 4.0 mm (0.157 in.) Center of seal packing
3.0 mm (0.118 in.)
- -
(A) - (A) 2.5 to 3.5 mm (0.0984 to 0.138 in.) Center of seal packing
2.5 mm (0.0984 in.)
- -
(B) - (B) 4.5 to 5.5 mm (0.177 to 0.217 in.) Opposite edge of seal packing
5.0 mm (0.197 in.)
- -
(C) - (C) 7.0 to 8.0 mm (0.276 to 0.315 in.) Opposite edge of seal packing
7.5 mm (0.295 in.)
- -
(F) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 15.5 mm (0.610 in.) 50.4 mm (1.98 in.)
(G) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 10.3 mm (0.406 in.) 143.1 mm (5.63 in.)
(H) 7.0 to 8.0 mm (0.276 to 0.315 in.) - 19.5 mm (0.768 in.) 153.4 mm (6.04 in.)
(I) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 16.0 mm (0.630 in.) 385.8 mm (1.27 ft.)
(J) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 18.6 mm (0.732 in.) 51.4 mm (2.02 in.)
(K) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 25.3 mm (0.996 in.) 121.9 mm (4.80 in.)
(L) 7.0 to 8.0 mm (0.276 to 0.315 in.) - 25.8 mm (1.02 in.) 147.2 mm (5.80 in.)
(M) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 5.1 mm (0.201 in.) 173.0 mm (6.81 in.)
(N) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 14.6 mm (0.575 in.) 385.8 mm (1.27 ft.)
(O) 4.0 mm (0.157 in.) Center of seal packing
3.0 mm (0.118 in.)
- -


NOTICE:

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.



j.

Clean the bolts and their installation holes.


k.
A057108C55
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.229,0.208 2.542,0.365 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 5 and a half threads or more of the end of the 2 bolts (E).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



l.
A374135C03
1.531,2.521 1.531,2.25 true 1.448,2.563 1.688,2.719 0.24,0.156 10 true *1 0.156,0.583 0.313,0.781 0.156,0.198 10 false E 2.781,0.563 2.938,0.76 0.156,0.198 10 false E 0.208,0.99 0.365,1.188 0.156,0.198 10 false A 0.25,1.271 0.406,1.469 0.156,0.198 10 false B 2.604,1.313 2.76,1.51 0.156,0.198 10 false B 2.458,1.677 2.615,1.875 0.156,0.198 10 false B 2.333,1.844 2.49,2.042 0.156,0.198 10 false A 2.531,1.906 2.688,2.104 0.156,0.198 10 false D 0.354,1.729 0.51,1.927 0.156,0.198 10 false B 0.385,2.083 0.542,2.281 0.156,0.198 10 false A 0.375,2.573 0.531,2.771 0.156,0.198 10 false A 1.552,1.656 1.708,1.854 0.156,0.198 10 true C 2.396,2.583 2.552,2.781 0.156,0.198 10 true D 2.51,2.885 2.667,3.083 0.156,0.198 10 true A 0.396,3.104 0.552,3.302 0.156,0.198 10 false A 2.469,3.323 2.625,3.521 0.156,0.198 10 false A 2.365,3.771 2.521,3.969 0.156,0.198 10 false A 1.771,4.427 1.927,4.625 0.156,0.198 10 false A
*1 Seal Washer


Temporarily install the timing chain cover sub-assembly with the 18 bolts and a new seal washer.

Bolt Length:
Item Length
Bolt (A), (E) 35 mm (1.38 in.)
Bolt (B), (D) 55 mm (2.17 in.)
Bolt (C) 40 mm (1.57 in.)


NOTICE:

Make sure that there is no oil on the threads of the bolts.



m.

Temporarily install the engine mounting bracket RH to the timing chain cover sub-assembly with the 3 bolts.

Bolt Length:
Item Length
Bolt 80 mm (3.15 in.)


NOTICE:

Make sure that there is no oil on the threads of the bolts.



n.

Install 2 new oil filter bracket O-rings to the timing chain cover sub-assembly.


o.

Temporarily install the oil filter bracket to the timing chain cover sub-assembly with the 4 bolts.

Bolt Length:
Item Length
Bolt 35 mm (1.38 in.)


NOTICE:

Make sure that there is no oil on the threads of the bolts.



p.

Fully tighten the 25 bolts in the order shown in the illustration.

A374525C01
0.802,0.052 1.115,0.208 0.313,0.156 10 false *a 4.115,0.073 4.427,0.229 0.313,0.156 10 false *b 0.698,0.802 0.854,1 0.156,0.198 10 false A 0.823,1.688 0.979,1.885 0.156,0.198 10 false A 0.823,2.094 0.979,2.292 0.156,0.198 10 false A 0.802,2.5 0.958,2.698 0.156,0.198 10 false A 0.813,2.667 0.969,2.865 0.156,0.198 10 false A 1.615,2.438 1.771,2.635 0.156,0.198 10 true A 1.625,3.333 1.781,3.531 0.156,0.198 10 true A 1.406,3.5 1.563,3.698 0.156,0.198 10 false A 1.979,3.604 2.135,3.802 0.156,0.198 10 false A 2.5,3.083 2.656,3.281 0.156,0.198 10 false A 2.583,2.698 2.74,2.896 0.156,0.198 10 false A 2.604,2.344 2.76,2.542 0.156,0.198 10 true A 2.5,2.083 2.656,2.281 0.156,0.198 10 true D 2.76,1.813 2.917,2.01 0.156,0.198 10 true D 1.781,1.313 1.938,1.51 0.156,0.198 10 true C 1.948,0.479 2.104,0.677 0.156,0.198 10 true F 2.521,1.656 2.677,1.854 0.156,0.198 10 false A 2.552,1.292 2.708,1.49 0.156,0.198 10 true B 2.698,1.073 2.854,1.271 0.156,0.198 10 true B 2.833,0.458 2.99,0.656 0.156,0.198 10 false E 0.656,0.5 0.813,0.698 0.156,0.198 10 false E 0.719,1.031 0.875,1.229 0.156,0.198 10 false B 0.802,1.396 0.958,1.594 0.156,0.198 10 false B 2.75,0.813 2.99,1.042 0.24,0.229 10 false F 5.906,1.292 6.063,1.49 0.156,0.198 10 false 1 4.125,1.396 4.281,1.594 0.156,0.198 10 false 2 6.063,1.063 6.219,1.26 0.156,0.198 10 false 3 4.021,1.031 4.177,1.229 0.156,0.198 10 false 4 6.146,0.427 6.302,0.625 0.156,0.198 10 false 5 5.833,1.656 6.052,1.938 0.219,0.281 10 false 6 6.083,1.823 6.24,2.021 0.156,0.198 10 true 7 5.802,2.094 5.958,2.292 0.156,0.198 10 true 8 5.906,2.333 6.063,2.531 0.156,0.198 10 true 9 5.865,2.719 6.177,2.917 0.313,0.198 10 false 10 5.781,3.083 6.094,3.281 0.313,0.198 10 false 11 5.26,3.604 5.573,3.802 0.313,0.198 10 false 12 4.052,2.5 4.365,2.698 0.313,0.198 10 false 13 4.052,2.083 4.365,2.281 0.313,0.198 10 false 14 4.083,1.667 4.396,1.865 0.313,0.198 10 false 15 3.938,0.781 4.25,0.979 0.313,0.198 10 false 16 3.885,0.49 4.198,0.688 0.313,0.198 10 false 17 5.031,1.281 5.344,1.479 0.313,0.198 10 true 18 6.052,0.802 6.365,1 0.313,0.198 10 false 19 5.208,0.49 5.521,0.688 0.313,0.198 10 true 20 5.865,1.49 6.177,1.688 0.313,0.198 10 false 21 4.063,2.698 4.375,2.896 0.313,0.198 10 false 22 4.688,3.51 5,3.708 0.313,0.198 10 false 23 4.896,2.375 5.208,2.573 0.313,0.198 10 true 24 4.875,3.333 5.188,3.531 0.313,0.198 10 true 25 2.531,1.49 2.688,1.688 0.156,0.198 10 false F
*a Torque *b Bolt Tightening Order


Torque:
Bolt (A), (D), (E) : 25.5 N*m (260 kgf*cm, 19 ft.*lbf)
Bolt (B), (F) : 51 N*m (520 kgf*cm, 38 ft.*lbf)
Bolt (C) : 10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Tighten the bolts within 10 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




Hide 11302A 34.INSTALL TIMING CHAIN COVER OIL SEAL

Hide 16031 35.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 83530 36.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89615 37.INSTALL KNOCK CONTROL SENSOR

Hide 11432A 38.INSTALL NO. 1 TAPER SCREW PLUG

a.
A378002C02
2.188,0.844 1.76,0.844 true 2.146,1.583 1.719,1.583 true 2.281,0.771 2.438,0.969 0.156,0.198 10 true A 2.219,1.51 2.375,1.708 0.156,0.198 10 true B 0.438,2.333 0.594,2.531 0.156,0.198 10 false A 2.052,2.25 2.208,2.448 0.156,0.198 10 false B 0.917,2.615 1.229,2.813 0.313,0.198 10 false *a 0.906,2.927 1.219,3.125 0.313,0.198 10 false *b 1.115,2.823 1.427,3.021 0.313,0.198 10 false *c 2.563,2.51 2.875,2.708 0.313,0.198 10 false *d 2.792,2.771 3.104,2.969 0.313,0.198 10 false *f 2.552,2.938 2.865,3.135 0.313,0.198 10 false *e
*a 5.0 mm (0.197 in.)
*b 11 mm (0.433 in.)
*c 18 mm (0.709 in.)
*d 8.0 mm (0.315 in.)
*e 12.5 mm (0.492 in.)
*f 22 mm (0.866 in.)


Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug, and install the No. 1 taper screw plug (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:
·

Install the No. 1 taper screw plug within 3 minutes of applying adhesive.

·

Do not start the engine for at least 1 hour after installing the No. 1 taper screw plug.




b.

Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug, and install the No. 1 taper screw plug (B).

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:
·

Install the No. 1 taper screw plug within 3 minutes of applying adhesive.

·

Do not start the engine for at least 1 hour after installing the No. 1 taper screw plug.




Hide 11401G 39.INSTALL CRANKSHAFT POSITION SENSOR

Hide 13540 41.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A378003C02
0.188,0.156 3.229,1.323 3.042,1.167 0.719,0.292 0.833,0.292 0.833,0.292 1.042,0.448 false 2.313,0.281 2.427,0.281 2.427,0.281 2.635,0.438 false 0.906,2.698 1.021,3.146 1.021,3.146 0.865,3.146 false 1.115,2.594 1.229,2.979 1.229,2.979 1.354,2.979 false 2.083,3.563 2.198,3.948 2.198,3.948 2.323,3.948 false 1.042,4.042 1.146,4.354 1.146,4.354 1.26,4.354 false 0.833,3.49 0.948,3.49 0.948,3.49 1.042,3.646 false 1.021,2.26 1.938,2.74 1.938,2.74 2.198,3.052 true 1.573,1.313 1.573,0.167 false 0.823,2.792 0.5,3.198 0.5,3.198 0.385,3.198 false 0.25,0.198 0.563,0.396 0.313,0.198 10 false *e 0.531,0.219 0.844,0.417 0.313,0.198 10 false *a 0.354,0.698 0.667,0.896 0.313,0.198 10 false *g 2.115,0.198 2.427,0.396 0.313,0.198 10 false *a 1.885,0.719 2.198,0.917 0.313,0.198 10 false *g 1.646,0.208 1.958,0.406 0.313,0.198 10 false *f 0.51,2.167 0.823,2.365 0.313,0.198 10 false *h 0.313,2.49 0.625,2.688 0.313,0.198 10 false *g 0.688,3.073 1,3.271 0.313,0.198 10 false *c 1.417,2.917 1.729,3.115 0.313,0.198 10 false *b 1.927,2.604 2.24,2.802 0.313,0.198 10 false *a 2.396,3.896 2.708,4.094 0.313,0.198 10 false *c 1.313,4.313 1.573,4.51 0.26,0.198 10 true *b 0.583,3.406 0.802,3.594 0.219,0.188 10 true *a 0.229,3.125 0.542,3.323 0.313,0.198 10 false *d
*a Cam
*b Hook
*c Plunger
*d Pin
*e Correct
*f Incorrect
*g Push
*h Raise


Raise the cam, then fully push in the plunger and engage the hook with the pin so that the plunger is in the position shown in the illustration.

NOTICE:

Make sure that the cam engages with the first tooth of the plunger to allow the hook to pass over the pin.



b.
A374527

Install a new gasket, the bracket and No. 1 chain tensioner assembly to the timing chain cover sub-assembly with the 2 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

If the hook releases the plunger while the No. 1 chain tensioner assembly is being installed, set the hook again.



c.
A374528C01
0.438,2.208 0.74,2.208 false 0.25,2.146 0.563,2.302 0.313,0.156 10 false *a 0.729,1.771 1.042,1.927 0.313,0.156 10 false *b
*a Hook
*b Release


Rotate the crankshaft counterclockwise slightly and check that the hook is released.


d.
A374529C01
0.844,2.323 1.021,2.125 false 1.042,2.031 1.354,2.188 0.313,0.156 10 false *a 0.563,2.635 0.875,2.792 0.313,0.156 10 false *b
*a Plunger
*b Plunger is extended


Turn the crankshaft clockwise and check that the plunger is extended.


Hide 15679 42.INSTALL OIL FILTER BRACKET CLIP

a.
A374526

Install the oil filter bracket clip to the oil filter bracket.


Hide 15620 43.INSTALL OIL FILTER CAP ASSEMBLY

Hide 11193 44.INSTALL SPARK PLUG TUBE GASKET

a.
A374173

Install 4 new spark plug tube gaskets to the cylinder head cover sub-assembly.


Hide 11213 45.INSTALL CYLINDER HEAD COVER GASKET

a.
A374174C01
1.719,2.375 1.938,2.24 false 1.76,2.948 1.958,3.104 false 1.979,2.167 2.292,2.323 0.313,0.156 10 false *1 2,3.083 2.313,3.24 0.313,0.156 10 false *2
*1 Cylinder Head Cover Sub-assembly
*2 Cylinder Head Cover Gasket


Install 3 new cylinder head cover gaskets to the cylinder head cover sub-assembly.

NOTICE:
·

Remove any oil from the contact surfaces.

·

Misalignment between the center of the cylinder head cover sub-assembly rib and the center of the cylinder head gasket tab should be 4.0 mm (0.157 in.) or less.




Hide 11201 46.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A374126

Install 2 new gaskets as shown in the illustration.


b.
A374175

Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Diameter:

4.0 mm (0.157 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
A374125

Install the cylinder head cover sub-assembly with the 16 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
A377157C01
2.24,1.573 2.5,1.417 true 0.917,1.854 1.979,1.854 true 1.667,1.906 1.979,2.063 0.313,0.156 10 false *1 2.375,1.917 2.688,2.073 0.313,0.156 10 false *2 2.552,1.344 2.865,1.5 0.313,0.156 10 false *3 0.688,1.781 1,1.938 0.313,0.156 10 false *a
*1 Timing Chain Cover Sub-assembly
*2 Camshaft Housing Sub-assembly
*3 Cylinder Head Cover Gasket
*a Projection


Misalignment between the contact surfaces of the timing chain cover sub-assembly and camshaft housing sub-assembly and the center of the cylinder head cover gasket tab should be 4.0 mm (0.157 in.) or less.



Hide 11101J 47.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 12108A 50.INSTALL OIL FILLER CAP GASKET

a.
A374530

Install the oil filler cap gasket to the oil filler cap sub-assembly.


Hide 12108 51.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.
A374429

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.