Home › Drivetrain › P610 HYBRID TRANSMISSION / TRANSAXLE › HYBRID TRANSAXLE OIL SEAL
RM3210E _52 Drivetrain _047503 P610 HYBRID TRANSMISSION / TRANSAXLE _0244917 HYBRID TRANSAXLE OIL SEAL A

P610 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH or front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

PROCEDURE

Hide 43420H 2.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C344931N02
2.292,2.906 2.75,2.906 false 2,2.833 2.323,3.042 0.323,0.208 10 false SST

Using SST, remove the front drive shaft oil seal LH from the hybrid vehicle transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the hybrid vehicle transaxle assembly.



Hide 43410M 3.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C344930N02
0.896,2.792 1.365,2.792 false 1.406,2.698 1.792,2.896 0.385,0.198 10 false SST

Using SST, remove the front drive shaft oil seal RH from the hybrid vehicle transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the hybrid vehicle transaxle assembly.



Hide 43410M 4.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C346718C02
1.49,2.281 0.948,2.125 0.948,2.125 1.552,2.104 false 0.76,0.417 1.01,0.594 0.25,0.177 10 false *a 0.646,2.042 0.979,2.229 0.333,0.188 10 false SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal RH to the hybrid vehicle transaxle assembly.

SST
09710-30050  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Do not allow foreign matter to attach to the lip of the front drive shaft oil seal RH.

·

Do not install the front drive shaft oil seal RH at an angle.




b.

Coat the lip of the front drive shaft oil seal RH with a small amount of MP grease.


Hide 43420H 5.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C346717C02
2.313,2.323 2.813,1.938 2.813,1.938 2.083,2.094 true 2.24,0.156 2.479,0.344 0.24,0.188 10 false *a 2.854,1.844 3.313,2.042 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal LH to the hybrid vehicle transaxle assembly.

SST
09649-17010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Do not allow foreign matter to attach to the lip of the front drive shaft oil seal LH.

·

Do not install the front drive shaft oil seal LH at an angle.




b.

Coat the lip of the front drive shaft oil seal LH with a small amount of MP grease.