Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM3210E _52 Drivetrain _047521 DRIVE SHAFT / PROPELLER SHAFT _0243355 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43420G 1.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING

a.

Install a new front drive shaft hole snap ring.

NOTICE:

Face the end gap of the front drive shaft hole snap ring downward.



Hide 43420 2.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

a.

Coat the splines of the front drive inboard joint assembly with ATF WS.


b.

Coat the lip of the front drive shaft oil seal LH with MP grease.


c.
C345600

Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

NOTICE:
·

Face the end gap of the front drive shaft hole snap ring downward.

·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.



HINT:

Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



d.
C344867C01
0,0 0,0 false
V100135

Toyota Body Grease W


Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.


e.
C345601C02
2.854,0.708 2.156,1.625 2.156,1.625 2.719,0.448 true 2.073,1.646 2.406,1.833 0.333,0.188 10 false *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.

NOTICE:
·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

·

Check that there is no foreign matter on the deflector or contact surfaces.

·

Do not damage the front drive shaft outboard joint boot.

·

Do not damage the front disc brake dust cover.

·

Do not damage the deflector.




Hide 43410 3.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 4.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 48810 5.INSTALL FRONT STABILIZER LINK ASSEMBLY

Hide 45047 6.CONNECT TIE ROD END SUB-ASSEMBLY

Hide 89543 7.INSTALL FRONT SPEED SENSOR

Hide 43502H 8.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.
C345602

Using a 30 mm deep socket wrench, install the front axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

HINT:

Keep depressing the brake pedal to prevent the drive shaft from rotating.



c.

Using a chisel and a hammer, stake the front axle shaft nut.


Hide 11.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 12.INSTALL FRONT WHEELS

Hide 51444C 14.INSTALL REAR MOTOR UNDER COVER LH

Hide 51443E 15.INSTALL REAR MOTOR UNDER COVER RH

Hide 51441 16.INSTALL NO. 1 ENGINE UNDER COVER