Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P082112  Gear Lever X Position Sensor 1 Circuit Short to Auxiliary Battery  P082114  Gear Lever X Position Sensor 1 Circuit Short to Ground or Open  P082211  Gear Lever Y Position Sensor 1 Circuit Short to Ground  P082215  Gear Lever Y Position Sensor 1 Circuit Short to Auxiliary Battery or Open  P181B62  Gear Lever Position Sensor Signal Compare Failure  P182112  Gear Lever X Position Sensor 2 Circuit Short to Auxiliary Battery  P182114  Gear Lever X Position Sensor 2 Circuit Short to Ground or Open  P182211  Gear Lever Y Position Sensor 2 Circuit Short to Ground  P182215  Gear Lever Y Position Sensor 2 Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

HINT:
·

The electronic shift lever system is a linkless type that does not use a shift cable.

·

The shift and select sensors are non-contact type sensors.



The shift lever (shift lock control unit assembly) is a momentary type, which returns to its home position by spring tension as the driver's hand is released from the shift lever after shifting.

The shift lever (shift lock control unit assembly) contains a shift sensor to detect the shift lever position (Home, R, N, D or B). Because the shift sensor operates using Hall ICs, they can accurately detect the shift lever position in a reliable manner.

A380421E01
0.958,2.563 1.24,2.281 false 1.115,4.521 1.49,4.344 false 4.563,2.594 5.417,2.031 true 5.333,3.615 5.177,4.302 5.177,4.302 5.521,3.615 true 0.177,0.135 4.302,0.729 4.125,0.594 10 false Shift Lock Control Unit Assembly 0.313,4.438 1.333,4.813 1.021,0.375 10 false Shift Sensor 0.219,2.552 1.333,2.979 1.115,0.427 10 false Shift Sensor 5,0.479 6.021,0.906 1.021,0.427 10 false Shift Sensor 3.188,2.563 4.594,3.271 1.406,0.708 10 false Magnet Shift Position 4.844,4.333 5.448,4.708 0.604,0.375 10 false Hall IC 0.135,0.635 0.844,0.854 0.708,0.219 12 false for LHD: 0.125,2.969 0.833,3.188 0.708,0.219 12 false for RHD:

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P082112 Gear Lever X Position Sensor 1 Circuit Short to Auxiliary Battery +B short in shift sensor 1 circuit
(1 trip detection logic)
·

Wire harness or connector

·

Shift lock control unit assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on
P082114 Gear Lever X Position Sensor 1 Circuit Short to Ground or Open Open or GND short in shift sensor 1 circuit
(1 trip detection logic)
·

Wire harness or connector

·

Shift lock control unit assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on
P082211 Gear Lever Y Position Sensor 1 Circuit Short to Ground Open or GND short in shift sensor 1 circuit
(1 trip detection logic)
·

Wire harness or connector

·

Shift lock control unit assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on
P082215 Gear Lever Y Position Sensor 1 Circuit Short to Auxiliary Battery or Open +B short in shift sensor 1 circuit
(1 trip detection logic)
·

Wire harness or connector

·

Shift lock control unit assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on
P181B62 Gear Lever Position Sensor Signal Compare Failure Shift sensor pattern malfunction
(1 trip detection logic)
·

Wire harness or connector

·

Shift lock control unit assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on
P182112 Gear Lever X Position Sensor 2 Circuit Short to Auxiliary Battery +B short in shift sensor 2 circuit
(1 trip detection logic)
·

Wire harness or connector

·

Shift lock control unit assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on
P182114 Gear Lever X Position Sensor 2 Circuit Short to Ground or Open Open or GND short in shift sensor 2 circuit
(1 trip detection logic)
·

Wire harness or connector

·

Shift lock control unit assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on
P182211 Gear Lever Y Position Sensor 2 Circuit Short to Ground Open or GND short in shift sensor 2 circuit
(1 trip detection logic)
·

Wire harness or connector

·

Shift lock control unit assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on
P182215 Gear Lever Y Position Sensor 2 Circuit Short to Auxiliary Battery or Open +B short in shift sensor 2 circuit
(1 trip detection logic)
·

Wire harness or connector

·

Shift lock control unit assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY).

7.

With the brake pedal depressed, slowly move the shift lever as follows to select each shift state: N → R → N → D → N → Home → B → Home.

8.

Push the P position switch (transmission shift main switch) to select park (P).

9.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A368279E03
4.948,7.073 6.823,7.49 1.875,0.417 10 false Hybrid Vehicle Control ECU 1.323,6.417 2.188,6.729 0.865,0.313 10 false Shift Sensor 0.229,7.115 3.427,7.552 3.198,0.438 10 false Shift Lever (Shift Lock Control Unit Assembly) 0.24,6.958 0.552,7.219 0.313,0.26 10 false F48 4.948,6.917 5.26,7.177 0.313,0.26 10 false F3 2.531,3.969 2.99,4.292 0.458,0.323 10 false VSX3 2.573,5.958 3.031,6.281 0.458,0.323 10 false E2X2 2.583,5.552 3.042,5.875 0.458,0.323 10 false E2X1 4.979,5.167 5.438,5.49 0.458,0.323 10 false VSI4 2.542,2.729 3,3.052 0.458,0.323 10 false VSX2 2.552,1.552 3.01,1.875 0.458,0.323 10 false VSX1 2.563,1.156 3.021,1.479 0.458,0.323 10 false VCX2 2.99,0.781 3.333,1.094 0.344,0.313 10 false 4 2.552,0.781 3.01,1.104 0.458,0.323 10 false VCX1 3.021,5.552 3.365,5.865 0.344,0.313 10 false 13 3,1.542 3.344,1.854 0.344,0.313 10 false 8 3,1.156 3.344,1.469 0.344,0.313 10 false 11 3.031,3.969 3.375,4.281 0.344,0.313 10 false 5 3.042,5.146 3.385,5.458 0.344,0.313 10 false 7 3.021,2.74 3.365,3.052 0.344,0.313 10 false 10 3.052,5.958 3.396,6.271 0.344,0.313 10 false 2 5,5.958 5.458,6.281 0.458,0.323 10 false E2X2 5,5.563 5.458,5.885 0.458,0.323 10 false E2X1 2.552,5.167 3.01,5.49 0.458,0.323 10 false VSX4 4.99,3.979 5.448,4.302 0.458,0.323 10 false VSI3 5.01,2.719 5.469,3.042 0.458,0.323 10 false VSI2 5.01,1.552 5.469,1.875 0.458,0.323 10 false VSI1 5,1.156 5.458,1.479 0.458,0.323 10 false VCX2 5,0.771 5.458,1.094 0.458,0.323 10 false VCX1 4.729,0.771 5.073,1.083 0.344,0.313 10 false 54 4.719,1.146 5.063,1.458 0.344,0.313 10 false 53 4.729,1.542 5.073,1.854 0.344,0.313 10 false 52 4.708,3.969 5.052,4.281 0.344,0.313 10 false 48 4.729,2.729 5.073,3.042 0.344,0.313 10 false 50 4.708,5.146 5.052,5.458 0.344,0.313 10 false 46 4.729,5.552 5.073,5.865 0.344,0.313 10 false 51 4.719,5.969 5.063,6.281 0.344,0.313 10 false 49

PROCEDURE

1.READ VALUE USING GTS (SHIFT SENSOR VOLTAGE)
a.

Connect the GTS the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Sensor Voltage (VSI1), Shift Sensor Voltage (VSI2), Shift Sensor Voltage (VSI3), Shift Sensor Voltage (VSI4).


d.

With the brake pedal depressed, while slowly move the shift lever as follows to select each shift state: N → R → N → D → N → Home → B → Home, read the Data List (Shift Sensor Voltage) displayed on the GTS.

HINT:

Wait with the shift lever in each state for 5 seconds or more.


Powertrain > Hybrid Control > Data List
Tester Display
Shift Sensor Voltage (VSI1)
Shift Sensor Voltage (VSI2)
Shift Sensor Voltage (VSI3)
Shift Sensor Voltage (VSI4)
50003 397 74,75,76,77
Result:
Data List Item Shift Lever Position
D N R B Home
Shift Sensor Voltage (VSI1) 1.63 to 2.40 V 0.68 to 1.62 V 0.40 to 0.67 V 2.75 to 3.52 V 3.53 to 4.47 V
Shift Sensor Voltage (VSI2) 2.70 to 3.52 V 1.63 to 2.70 V 0.98 to 1.62 V 1.63 to 2.45 V 2.45 to 3.52 V
Shift Sensor Voltage (VSI3) 3.53 to 4.17 V 2.45 to 3.52 V 1.63 to 2.45 V 0.98 to 1.63 V 1.63 to 2.70 V
Shift Sensor Voltage (VSI4) 4.47 to 4.75 V 3.53 to 4.47 V 2.75 to 3.52 V 0.40 to 0.67 V 0.68 to 1.62 V



e.

Push the P position switch (transmission shift main switch) to select park (P).


f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK FOR INTERMITTENT PROBLEMS

NG

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT LOCK CONTROL UNIT ASSEMBLY)
2.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the F3 hybrid vehicle control ECU connector.


b.

Disconnect the F48 shift lock control unit assembly connector.


c.
A370128C03
1.5,0.125 1.885,0.396 0.385,0.271 0.219,3.302 0.604,3.573 0.385,0.271 2.708,1.563 2.906,1.677 true 2.521,1.563 2.76,1.813 true 2.375,1.573 2.469,1.99 true 2.229,1.563 2.208,2.219 true 2.073,1.573 1.854,2.219 true 1.917,1.573 1.521,2.135 true 1.76,1.563 1.281,2.021 true 1.448,1.552 0.958,1.938 true 2.344,2.844 1.667,3.385 true 1.667,3.698 1.656,4.167 true 1.167,3.698 0.615,3.99 true 1.51,3.698 1.135,4.146 true 2.552,3 1.823,3.385 true 2.531,3.583 2.177,3.438 true 2.177,4.104 2,3.74 true 1.365,3.385 0.802,2.917 true 0.177,0.125 0.49,0.323 0.313,0.198 10 false *a 2.958,1.635 3.417,1.896 0.458,0.26 10 false VCX1 2.667,1.885 3.125,2.146 0.458,0.26 10 false VCX2 0.979,2.042 1.438,2.302 0.458,0.26 10 false VSI3 1.698,2.24 2.156,2.5 0.458,0.26 10 false VSI2 0.604,1.865 1.063,2.125 0.458,0.26 10 false VSI4 2.063,2.26 2.521,2.521 0.458,0.26 10 false E2X1 1.323,2.156 1.781,2.417 0.458,0.26 10 false E2X2 1.604,0.177 1.917,0.375 0.313,0.198 10 false F3 1.51,4.24 1.969,4.5 0.458,0.26 10 false VCX2 2.354,2.042 2.813,2.302 0.458,0.26 10 false VSI1 0.906,4.177 1.365,4.438 0.458,0.26 10 false VSX2 2.615,2.938 3.073,3.198 0.458,0.26 10 false VSX3 2.573,3.542 3.031,3.802 0.458,0.26 10 false VSX4 2.115,4.156 2.573,4.417 0.458,0.26 10 false E2X1 0.417,2.802 0.875,3.063 0.458,0.26 10 false E2X2 2.365,2.719 2.823,2.979 0.458,0.26 10 false VCX1 0.292,4.01 0.75,4.271 0.458,0.26 10 false VSX1 0.292,3.354 0.75,3.615 0.458,0.26 10 false F48 0.198,2.417 0.51,2.615 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Lock Control Unit Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F3-54 (VCX1) - F48-4 (VCX1) Power switch off Below 1 Ω
F3-53 (VCX2) - F48-11 (VCX2) Power switch off Below 1 Ω
F3-52 (VSI1) - F48-8 (VSX1) Power switch off Below 1 Ω
F3-50 (VSI2) - F48-10 (VSX2) Power switch off Below 1 Ω
F3-48 (VSI3) - F48-5 (VSX3) Power switch off Below 1 Ω
F3-46 (VSI4) - F48-7 (VSX4) Power switch off Below 1 Ω
F3-51 (E2X1) - F48-13 (E2X1) Power switch off Below 1 Ω
F3-49 (E2X2) - F48-2 (E2X2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F3-54 (VCX1) or F48-4 (VCX1) - Body ground and terminals other than F48-11 (VCX2) Power switch off 10 kΩ or higher
F3-53 (VCX2) or F48-11 (VCX2) - Body ground and terminals other than F48-4 (VCX1) Power switch off 10 kΩ or higher
F3-52 (VSI1) or F48-8 (VSX1) - Body ground and other terminals Power switch off 10 kΩ or higher
F3-50 (VSI2) or F48-10 (VSX2) - Body ground and other terminals Power switch off 10 kΩ or higher
F3-48 (VSI3) or F48-5 (VSX3) - Body ground and other terminals Power switch off 10 kΩ or higher
F3-46 (VSI4) or F48-7 (VSX4) - Body ground and other terminals Power switch off 10 kΩ or higher
F3-51 (E2X1) or F48-13 (E2X1) - Body ground and terminals other than F48-2 (E2X2) Power switch off 10 kΩ or higher
F3-49 (E2X2) or F48-2 (E2X2) - Body ground and terminals other than F48-13 (E2X1) Power switch off 10 kΩ or higher



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-54 (VCX1) or F48-4 (VCX1) - Body ground Power switch on (IG) Below 1 V
F3-53 (VCX2) or F48-11 (VCX2) - Body ground Power switch on (IG) Below 1 V
F3-52 (VSI1) or F48-8 (VSX1) - Body ground Power switch on (IG) Below 1 V
F3-50 (VSI2) or F48-10 (VSX2) - Body ground Power switch on (IG) Below 1 V
F3-48 (VSI3) or F48-5 (VSX3) - Body ground Power switch on (IG) Below 1 V
F3-46 (VSI4) or F48-7 (VSX4) - Body ground Power switch on (IG) Below 1 V
F3-51 (E2X1) or F48-13 (E2X1) - Body ground Power switch on (IG) Below 1 V
F3-49 (E2X2) or F48-2 (E2X2) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU and shift lock control unit assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the F48 shift lock control unit assembly connector.


j.

Reconnect the F3 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HYBRID VEHICLE CONTROL ECU (VCX1, VCX2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HYBRID VEHICLE CONTROL ECU (VCX1, VCX2 VOLTAGE)
a.

Disconnect the F48 shift lock control unit assembly connector.


b.

Turn the power switch on (IG).


c.
A367827C03
1.469,0.219 1.875,0.49 0.406,0.271 1.385,1.219 0.885,1 true 1.708,1.219 2.521,0.771 true 2.375,1.875 2.031,1.542 true 1.615,1.906 1.719,1.563 true 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 2.573,0.667 3.063,0.927 0.49,0.26 10 false VCX1 1.417,1.927 1.906,2.146 0.49,0.219 10 false VCX2 2.427,1.906 2.917,2.167 0.49,0.26 10 false E2X1 0.5,0.885 0.99,1.146 0.49,0.26 10 false E2X2 1.552,0.271 2.042,0.531 0.49,0.26 10 false F48
*a Front view of wire harness connector
(to Shift Lock Control Unit Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F48-4 (VCX1) - F48-13 (E2X1) Power switch on (IG) 4.5 to 5.5 V
F48-11 (VCX2) - F48-2 (E2X2) Power switch on (IG) 4.5 to 5.5 V


NOTICE:

Turning the power switch on (IG) with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the F48 shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

5.REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK DTC OUTPUT (HYBRID CONTROL)
7.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

With the brake pedal depressed, slowly move the shift lever as follows to select each shift state: N → R → N → D → N → Home → B → Home.


d.

Push the P position switch (transmission shift main switch) to select park (P).


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs are output. A
P082112, P082114, P082211, P082215, P181B62, P182112, P182114, P182211 or P182215 is output again. B



g.

Turn the power switch off.



A

COMPLETED

B