Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A3611  Generator Temperature Sensor Circuit Short to Ground  P0A3615  Generator Temperature Sensor Circuit Short to Auxiliary Battery or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the generator temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Hybrid vehicle control ECU internal malfunction
·

Hybrid vehicle control ECU malfunction


Generator temperature sensor malfunction
·

Internal generator temperature sensor malfunction

·

Open or short in generator temperature sensor


Wire harness between the generator temperature sensor and hybrid vehicle control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness


HINT:

If any of these DTCs are stored, the generator temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the generator (MG1) becomes high. If the self-protection function does not operate, the generator (MG1) may malfunction and cause the vehicle to enter fail-safe mode.



DESCRIPTION

The resistance of the thermistor built into the generator temperature sensor changes in accordance with changes in generator (MG1) temperature. The lower the generator (MG1) temperature, the higher the thermistor resistance. Conversely, the higher the generator (MG1) temperature, the lower the resistance.

C189867E17
0.76,2.104 0.885,2.302 0.125,0.198 10 false 0 2,2.875 3.406,3.094 1.406,0.219 10 false Temperature (°C (°F)) 0.885,2.375 1.083,2.573 0.198,0.198 10 false 10 1.26,2.375 1.458,2.573 0.198,0.198 10 false 15 2.406,2.375 2.604,2.573 0.198,0.198 10 false 30 2.792,2.375 2.99,2.573 0.198,0.198 10 false 35 1.646,2.375 1.844,2.573 0.198,0.198 10 false 20 2.021,2.375 2.219,2.573 0.198,0.198 10 false 25 0.677,1.521 0.875,1.719 0.198,0.198 10 false 50 0.594,0.948 0.865,1.146 0.271,0.198 10 false 100 3.146,2.375 3.344,2.573 0.198,0.198 10 false 40 0.063,0.5 1.26,0.771 1.198,0.271 10 false Resistance (kΩ) 0.865,2.542 1.208,2.74 0.344,0.198 10 false (50) 1.229,2.552 1.573,2.75 0.344,0.198 10 false (59) 1.615,2.552 1.958,2.75 0.344,0.198 10 false (68) 1.979,2.563 2.323,2.76 0.344,0.198 10 false (77) 2.385,2.573 2.729,2.771 0.344,0.198 10 false (86) 2.771,2.583 3.115,2.781 0.344,0.198 10 false (95) 3.063,2.583 3.406,2.781 0.344,0.198 10 false (104)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A3611 Generator Temperature Sensor Circuit Short to Ground Short to ground in the generator temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Hybrid vehicle generator assembly (Generator temperature sensor)


Does not come on Master Warning Light:
Comes on
P0A3615 Generator Temperature Sensor Circuit Short to Auxiliary Battery or Open Open or short to +B in the generator temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Hybrid vehicle generator assembly (Generator temperature sensor)


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0A3611 Generator Temperature
P0A3615

HINT:

After confirming that DTC P0A3611 or P0A3615 is output, use the GTS to check "Generator Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to ground


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A385273E01
4.969,2.844 6.979,3.396 2.01,0.552 10 false Hybrid Vehicle Control ECU 0.531,2.823 2.542,3.375 2.01,0.552 10 false Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly) 0.531,2.667 0.844,2.865 0.313,0.198 10 false C8 4.958,2.677 5.271,2.875 0.313,0.198 10 false A50 5.938,1.281 6.427,1.625 0.49,0.344 10 false ADC 4.865,1.917 5.417,2.219 0.552,0.302 10 false GMTG 4.854,1.167 5.333,1.458 0.479,0.292 10 false GMT 1.885,1.167 2.365,1.458 0.479,0.292 10 false GMT 1.802,1.906 2.354,2.208 0.552,0.302 10 false GMTG 4.604,1.167 4.948,1.49 0.344,0.323 10 false 48 4.604,1.917 4.948,2.24 0.344,0.323 10 false 47 2.313,1.146 2.656,1.469 0.344,0.323 10 false 5 2.302,1.917 2.646,2.24 0.344,0.323 10 false 4 3.677,1.167 4.021,1.49 0.344,0.323 10 false 14 3.042,1.167 3.385,1.49 0.344,0.323 10 false 14 3.677,1.906 4.021,2.229 0.344,0.323 10 false 15 3.052,1.917 3.396,2.24 0.344,0.323 10 false 15 2.615,2.635 4.729,3.188 2.115,0.552 10 false No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly Connector 2.604,2.469 2.917,2.667 0.313,0.198 10 false CA2

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR TEMPERATURE SENSOR CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR TEMPERATURE SENSOR CONNECTOR)
a.
A376648

Check the connection condition of the generator temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.READ VALUE USING GTS (GENERATOR TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.READ VALUE USING GTS (GENERATOR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Generator Temperature.


d.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Generator Temperature
50003 397 62
Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

4.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)

B

6.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
a.
A376648

Disconnect the C8 generator temperature sensor connector.


b.
A385118C03
1.156,1.729 1.292,1.323 false 1.646,1.75 1.521,1.313 false 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 0.958,1.75 1.385,1.979 0.427,0.229 10 false GMT 1.49,1.76 1.917,1.99 0.427,0.229 10 false GMTG
*a Component without harness connected
(Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5(GMT) - 4(GMTG) Power switch OFF 0.3338 to 1487 kΩ



c.

Reconnect the C8 generator temperature sensor connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU CONNECTOR)
a.

Connect terminals 48 (GMT) and 47 (GMTG) of the A50 hybrid vehicle control ECU.

A365591C42
1.479,0.344 1.823,0.594 0.344,0.25 1.198,1.604 1.448,2.385 true 1.063,1.615 1.042,2.375 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.531,0.385 1.99,0.583 0.458,0.198 10 false A50 1.302,2.417 1.792,2.667 0.49,0.25 10 false GMTG 0.854,2.417 1.469,2.615 0.615,0.198 10 false GMT
*a Component with harness connected
(to Hybrid Vehicle Control ECU)
- -



b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Generator Temperature.


e.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Generator Temperature
50003 397 62
OK:
Tester Display Condition Specified Condition
Generator Temperature Terminals A50-48 (GMT) and A50-47 (GMTG) connected
Power switch on (IG)
215°C (419°F)



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
a.
A376648

Disconnect the C8 generator temperature sensor connector.


b.
A385118C03
1.156,1.729 1.292,1.323 false 1.646,1.75 1.521,1.313 false 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 0.958,1.75 1.385,1.979 0.427,0.229 10 false GMT 1.49,1.76 1.917,1.99 0.427,0.229 10 false GMTG
*a Component without harness connected
(Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5(GMT) - 4(GMTG) Power switch OFF 0.3338 to 1487 kΩ



c.

Reconnect the C8 generator temperature sensor connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU CONNECTOR)
a.

Disconnect the C8 generator temperature sensor connector.


b.

Disconnect the A50 hybrid vehicle control ECU connector.


c.
A377946C06
1.521,0.229 1.833,0.49 0.313,0.26 1.531,2.156 1.917,2.417 0.385,0.26 2.104,1.615 1.979,1.135 true 1.656,1.615 1.844,1.135 true 2.281,4.156 2.469,3.677 true 2.76,4.146 2.635,3.667 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.208,2.219 0.521,2.417 0.313,0.198 10 false *b 1.594,0.292 1.906,0.49 0.313,0.198 10 false C8 1.594,2.208 1.906,2.406 0.313,0.198 10 false A50 1.979,1.656 2.438,1.885 0.458,0.229 10 false GMT 1.417,1.656 1.875,1.885 0.458,0.229 10 false GMTG 2.021,4.198 2.479,4.427 0.458,0.229 10 false GMTG 2.625,4.188 3.083,4.417 0.458,0.229 10 false GMT
*a Front view of wire harness connector
(to Generator Temperature Sensor)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C8-5 (GMT) - A50-48 (GMT) Power switch off Below 1 Ω
C8-4 (GMTG) - A50-47 (GMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C8-5 (GMT) or A50-48 (GMT) - Body ground and other terminals Power switch off 10 kΩ or higher
C8-4 (GMTG) or A50-47 (GMTG) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the A50 hybrid vehicle control ECU.


e.

Reconnect the C8 generator temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR