Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P272C81  Park Pawl Motor Invalid Serial Data Received  


DESCRIPTION

The hybrid vehicle control ECU receives signals from the P position switch and shift lever and operates the shift control actuator assembly through current control to engage and release the parking lock. If the actual shift state and requested shift state do not match, the hybrid vehicle control ECU detects the malfunction and stores this DTC.

A368526E01
5.833,0.25 6,0.25 6,0.25 6.198,1.219 false 0.177,1.135 1.375,1.604 1.198,0.469 10 false P Position Switch 0.385,1.969 1.24,2.354 0.854,0.385 10 false Shift Lever 1.396,3.25 2.75,3.615 1.354,0.365 10 false Certification ECU 2.479,1.26 3.833,1.625 1.354,0.365 10 false P position signal 2.406,0.792 3.76,1.156 1.354,0.365 10 false P control signal 4.417,1.271 5.771,1.635 1.354,0.365 10 false Motor Position signal 4.406,0.792 5.76,1.156 1.354,0.365 10 false Actuator Energized 5.573,1.677 7.135,2.271 1.563,0.594 10 false Hybrid Vehicle Transaxle Assembly 4.49,0.167 5.865,0.688 1.375,0.521 10 false Shift Control Actuator Assembly 2.594,2.063 4.5,2.677 1.906,0.615 10 false Hybrid Vehicle Control ECU

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P272C81 Park Pawl Motor Invalid Serial Data Received With the power switch on (IG), the actual shift state and requested shift state do not match for 5 seconds or more.
(1 trip detection logic)
·

Hybrid vehicle control ECU

·

Auxiliary battery


Does not come on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Depress the brake pedal and move the shift lever to select neutral (N).

7.

Push the P position switch (transmission shift main switch).

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
None of the DTCs in the table below are output. A
Any of the DTCs in the table below are output. B


Relevant DTC
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
P06881F ECM/PCM Power Relay Sense Circuit Intermittent


e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Release the brake pedal and turn the power switch on (IG).

HINT:

Do not turn the power switch on (READY).



c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P272C81.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Hybrid Control
Tester Display
BATT Voltage for Transmission Control System

Result:
Result Proceed to
BATT Voltage for Transmission Control System is 9 V or more. A
BATT Voltage for Transmission Control System is less than 9 V. B


e.

Turn the power switch off.



A

3.CLEAR DTC

B

3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.

Powertrain > Hybrid Control > Trouble Codes
50001 397

e.

Clear the DTCs.


f.

Disconnect the GTS from the DLC3.


g.

Turn the power switch off.


h.

Leave the vehicle as is for 60 seconds or more.

NOTICE:
·

Do not connect the GTS.

·

Do not depress brake pedal.

·

Do not open/close any of the doors.




i.

Check for DTCs again.


Result:
Proceed to
NEXT



NEXT

4.CHARGE AUXILIARY BATTERY
4.CHARGE AUXILIARY BATTERY
a.

Charge the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT (SIMULATION TEST)
5.CHECK DTC OUTPUT (SIMULATION TEST)
a.

Connect the GTS to the DLC3.


b.

Release the brake pedal and turn the power switch on (IG).

HINT:

Do not turn the power switch on (READY).



c.

Depress the brake pedal and move the shift lever to select neutral (N).


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTC P272C81 is output. A
DTC P272C81 is not output. B


f.

Turn the power switch off.



A

B

END (AUXILIARY BATTERY WAS INSUFFICIENTLY CHARGED)