Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P314A31  Motor Electronics Coolant Pump "A" No Signal  


DESCRIPTION

Refer to the description for DTC P0C7396.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C7396

The inverter water pump assembly sends the inverter water pump speed (measured value) signal to the hybrid vehicle control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P314A31 Motor Electronics Coolant Pump "A" No Signal The inverter water pump speed signal is not sent to the hybrid vehicle control ECU when the power switch is turned on (READY).*
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Inverter water pump assembly

·

INV W/PMP fuse

·

IGCT relay


Comes on Master Warning Light:
Comes on

*: Either of the following conditions is met.
·

A malfunction (open, short to +B or short to ground) in the speed signal line from the inverter water pump assembly to the hybrid vehicle control ECU is detected.

·

A malfunction in the inverter water pump assembly power source circuit is detected.

·

A malfunction in the +B line is detected.

·

A malfunction in hybrid vehicle control ECU power source circuit is detected.


Related Data List
DTC No. Data List
P314A31
·

Inverter Water Pump Revolution

·

Inverter Water Pump Duty Ratio

·

Ready Signal



Related Active Test
DTC No. Active Test
P314A31 Activate the Inverter Water Pump

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0C7396.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C7396

PROCEDURE

1.CLEAR DTC

NEXT

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.


d.

Perform the "Activate the Inverter Water Pump" Active Test.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Inverter Water Pump
50004 397 1

e.

Touch the inverter water pump assembly and check that it is operating (vibrating).

OK:

The inverter water pump is operating (vibrating).



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Disconnect the A7 inverter water pump assembly connector.


c.
A368425C06
1.542,2.688 1.896,2.958 0.354,0.271 1.427,0.333 1.823,0.594 0.396,0.26 2.24,2.302 2.396,1.698 true 1.5,4.083 1.615,3.542 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 0.188,2.729 0.5,2.927 0.313,0.198 10 false *b 1.344,4.125 1.896,4.417 0.552,0.292 10 false NWP 2.115,2.344 2.667,2.635 0.552,0.292 10 false NIWP 1.5,0.396 2.052,0.688 0.552,0.292 10 false A50 1.635,2.75 2.188,3.042 0.552,0.292 10 false A7
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A50-33 (NIWP) - A7-2 (NWP) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A50-33 (NIWP) or A7-2 (NWP) -Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the A7 inverter water pump assembly connector.


e.

Reconnect the A50 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect the A7 inverter water pump assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

A365591C47
5.271,0.344 5.615,0.594 0.344,0.25 1.552,0.281 1.896,0.531 0.344,0.25 1.26,1.5 1.51,2.281 true 6.021,1.302 5.896,2.302 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 5.344,0.396 5.802,0.594 0.458,0.198 10 false F3 1.427,2.323 1.917,2.573 0.49,0.25 10 false NIWP 5.771,2.365 6.385,2.563 0.615,0.198 10 false E1 1.604,0.333 2.063,0.531 0.458,0.198 10 false A50
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A50-33 (NIWP) - F3-3 (E1) Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the A7 inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

7.CLEAR DTC

NEXT

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.


d.

Perform the "Activate the Inverter Water Pump" Active Test.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Inverter Water Pump
50004 397 1

e.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.

A368673C03
1.385,0.177 1.792,0.438 0.406,0.26 5.333,0.177 5.698,0.448 0.365,0.271 5.896,2.01 5.958,1.146 true 0.938,2.063 1.188,1.333 true 4.573,3.073 5.083,3.344 0.51,0.271 10 false GND 5.802,2.052 6.313,2.323 0.51,0.271 10 false E1 0.76,2.115 1.271,2.385 0.51,0.271 10 false NIWP 1.458,0.229 1.969,0.5 0.51,0.271 10 false A50 5.427,0.24 5.938,0.51 0.51,0.271 10 false F3 0.135,0.146 0.646,0.417 0.51,0.271 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Item Content
Terminal A50-33 (NIWP) - F3-3 (E1)
Equipment Setting 5 V/DIV., 100 ms./DIV.
Condition Power switch on (IG), during Active Test

OK:

The duration of wavelength A is 300 msec or less.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

10.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - IGCT RELAY)

NG

12.CHECK FUSE (INV W/PMP)
10.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - IGCT RELAY)
a.

Remove the IGCT relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the A7 inverter water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

A378452C02
1.594,0.667 1.917,0.927 0.323,0.26 2.219,2.073 2.042,1.51 true 1.677,0.729 1.99,0.927 0.313,0.198 10 false A7 3.75,0.188 4.063,0.385 0.313,0.198 10 false *1 0.948,0.625 1.26,0.823 0.313,0.198 10 false *a 5.844,1.094 6.156,1.292 0.313,0.198 10 false *2 2.083,2.115 2.563,2.417 0.479,0.302 10 false +BWP
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly *2 IGCT Relay
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A7-4 (+BWP) - 5 (IGCT relay) Power switch off Below 1 Ω


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.


HINT:
A288054C02
0.177,0.177 0.49,0.375 0.313,0.198 10 *a 0.99,1.385 1.302,1.583 0.313,0.198 10 *b 2.021,2.979 2.333,3.177 0.313,0.198 10 *c
*a Example
*b Shake Slightly
*c Vibrate Slightly


·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly

Apply slight vibration with a finger to the No. 1 engine room relay block and No. 1 junction block assembly and check whether a malfunction occurs.

·

INV W/PMP fuse

Apply slight vibration with a finger to the INV W/PMP fuse and check whether a malfunction occurs.

·

IGCT relay

Apply slight vibration with a finger to the IGCT relay and check whether a malfunction occurs.




d.

Reconnect the A7 inverter water pump assembly connector.


e.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

NG

13.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
11.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the A7 inverter water pump assembly connector.


b.
A288050C61
1.448,1.052 1.865,1.292 0.417,0.24 1.125,2.448 1.365,1.896 false 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 0.99,2.5 1.448,2.698 0.458,0.198 10 false GND 1.594,1.104 1.917,1.271 0.323,0.167 10 false A7
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-1 (GND) - Body ground Power switch off Below 1 Ω



c.

Reconnect the A7 inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK FUSE (INV W/PMP)
a.
A377963C01
2.667,1.802 1.917,1.646 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *1 2.74,1.781 3.052,1.979 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

CONNECT SECURELY (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

16.CONNECT SECURELY
13.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
a.

Check installation condition of the INV W/PMP fuse.

OK:

INV W/PMP fuse is installed correctly.



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)

NG

17.CHECK FUSE HOLDER TERMINAL (INV W/PMP FUSE)
14.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)
a.

Remove the INV W/PMP fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Remove the IGCT relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the A7 inverter water pump assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

A378455C02
1.417,0.875 1.75,1.135 0.333,0.26 2.021,2.135 1.844,1.646 true 0.635,0.823 0.948,1.021 0.313,0.198 10 false *a 1.51,0.938 1.823,1.135 0.313,0.198 10 false A7 1.917,2.177 2.479,2.5 0.563,0.323 10 false +BWP 3.708,0.135 4.021,0.333 0.313,0.198 10 false *1 3.354,0.938 3.667,1.135 0.313,0.198 10 false *2 5.844,1.094 6.156,1.292 0.313,0.198 10 false *3
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly *2 INV W/PMP Fuse
*3 IGCT Relay - -
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2 (INV W/PMP fuse) - A7-4 (+BWP) Power switch off Below 1 Ω
1 (INV W/PMP fuse) - 5 (IGCT relay) Power switch off Below 1 Ω
2 (INV W/PMP fuse) or A7-4 (+BWP) - Body ground and other terminals Power switch off 10 kΩ or higher


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.



e.

Reconnect the A7 inverter water pump assembly connector.


f.

Install the IGCT relay.


g.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

15.CHECK FUSE (INV W/PMP)

NG

19.CHECK FUSE (INV W/PMP)
15.CHECK FUSE (INV W/PMP)
a.
A377963C01
2.667,1.802 1.917,1.646 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *1 2.74,1.781 3.052,1.979 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)

NG

20.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
16.CONNECT SECURELY
a.

Connect the inverter water pump assembly connector securely.


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP)

17.CHECK FUSE HOLDER TERMINAL (INV W/PMP FUSE)
a.

Check the terminals of the INV W/PMP fuse holder.

OK:

The terminals of the INV W/PMP fuse holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

18.CHECK FUSE (INV W/PMP)

NG

23.CHECK FUSE (INV W/PMP)
18.CHECK FUSE (INV W/PMP)
a.
A377963C01
2.667,1.802 1.917,1.646 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *1 2.74,1.781 3.052,1.979 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

CONNECT SECURELY (INV W/PMP FUSE)

NG

REPLACE FUSE (INV W/PMP)

19.CHECK FUSE (INV W/PMP)
a.
A377963C01
2.667,1.802 1.917,1.646 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *1 2.74,1.781 3.052,1.979 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

24.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the A7 inverter water pump assembly connector.


b.
A288050C61
1.448,1.052 1.865,1.292 0.417,0.24 1.125,2.448 1.365,1.896 false 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 0.99,2.5 1.448,2.698 0.458,0.198 10 false GND 1.594,1.104 1.917,1.271 0.323,0.167 10 false A7
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-1 (GND) - Body ground Power switch off Below 1 Ω



c.

Reconnect the A7 inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

21.CHECK FUSE HOLDER TERMINAL (INV W/PMP FUSE)

NG

24.REPAIR OR REPLACE HARNESS OR CONNECTOR
21.CHECK FUSE HOLDER TERMINAL (INV W/PMP FUSE)
a.

Check the terminals of the INV W/PMP fuse holder.

OK:

The terminals of the INV W/PMP fuse holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

22.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)
22.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

REPLACE FUSE (INV W/PMP)

23.CHECK FUSE (INV W/PMP)
a.
A377963C01
2.667,1.802 1.917,1.646 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *1 2.74,1.781 3.052,1.979 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)
24.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP)

25.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP)