MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU detects a VB sensor or VL sensor malfunction.
The cause of this malfunction may be one of the following:
Voltage sensor malfunction
Motor generator control ECU (MG ECU) malfunction
Communication (wire harness) malfunction
HV battery malfunction
HV battery junction block assembly malfunction
Inverter with converter assembly malfunction
High-voltage wire harness malfunction
High-voltage connector or connection malfunction
Inspection Overview
| Inspection Content | Reason (Narrow Down in Order Using Inspection Procedures Below) | Inspection Step |
|---|---|---|
| Check for DTCs (HV) | Output DTCs | 1 |
| Check for DTCs (check voltage sensor malfunction locations)
Check for DTCs (drive test) |
Put vehicle in ready ON (vehicle stopped or being driven) and then check whether DTCs are output again. | 3, 4 |
| Read value using GTS | Data List value | 5 |
| Check freeze frame data (HV) | FREEZE FRAME DATA | 6, 7 |
| Read value using GTS | Accelerator and brake pedal simultaneously depressed Data List value | 8 |
For a description of the boost converter.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P0CA300
The MG ECU uses a voltage sensor (VL) that is built into the boost converter to detect the high voltage before it is boosted. The ECU also uses the battery voltage sensor to detect HV battery voltage (VB).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P1C2D62 | Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure | Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate:
Difference between "VL-Voltage before Boosting" and "Hybrid Battery Voltage" is large when the boosting request is given. (1 trip detection logic) |
·
Inverter with converter assembly ·
Battery voltage sensor |
Comes on | Master Warning Light:
Comes on |
| DTC No. | Data List |
|---|---|
| P1C2D62 | ·
Hybrid Battery Voltage ·
VL-Voltage before Boosting ·
VH-Voltage after Boosting ·
Boost Ratio |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Turn the power switch on (READY).
With the shift lever in D, depress both the accelerator pedal and brake pedal at the same time to raise the "Hybrid Battery SOC" to a sufficient level.
Move the shift lever to P, check that the engine is stopped and move the shift lever to N.
Set the A/C for maximum cooling.
Leave the vehicle for a few minutes.
When the accelerator pedal is not depressed with the power switch on (READY) and park (P) selected, if "VL-Voltage before Boosting" and the "Hybrid Battery Voltage" is approximately the same after repair, the condition is judged as normal.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
One of the following applies:
·
Only P1C2D62 is output. ·
One or more DTCs other than P0E311C, P0CA300, P0B231C, and DTCs in the table below are also output. |
A |
| P1C2D62 and P0E311C or P0CA300 are output at the same time. | B |
| P1C2D62 and P0B231C are output at the same time. | C |
| DTCs of hybrid control system in the tables below are output. | D |
| DTCs of motor generator control system in the tables below are output. | E |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Microcomputer malfunction | Hybrid control system | P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
| P0A1B49 | Drive Motor "A" Control Module Internal Electronic Failure | ||
| P0AFC00 | Hybrid/EV Battery Sensor Module | ||
| P0AFC96 | Hybrid/EV Battery Sensor Module Component Internal Failure | ||
| Motor generator control system | P0A1A47 | Generator Control Module Watchdog / Safety μC Failure | |
| P0A1A49 | Generator Control Module Internal Electronic Failure | ||
| P0A1B1F | Generator Control Module Circuit Intermittent | ||
| P1C2A1C | Generator A/D Converter Circuit Circuit Voltage Out of Range | ||
| P1C2A49 | Generator A/D Converter Circuit Internal Electronic Failure | ||
| P313383 | Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect | ||
| P313386 | Communication Error from Generator to Drive Motor "A" Signal Invalid | ||
| P313387 | Communication Error from Generator to Drive Motor "A" Missing Message | ||
| Power source circuit malfunction | Hybrid control system | P0AFC16 | Hybrid/EV Battery Sensor Module Circuit Voltage Below Threshold |
| Motor generator control system | P06D61C | Generator Control Module Offset Power Circuit Voltage Out of Range | |
| Communication system malfunction | Hybrid control system | P312387 | Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
| U029A87 | Lost Communication with Hybrid/EV Battery Sensor Module Missing Message | ||
| Sensor and actuator circuit malfunction | Hybrid control system | P0B3B14 | Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open |
| P0B4014 | Hybrid/EV Battery Voltage Sensor "B" Circuit Short to Ground or Open | ||
| P0B4514 | Hybrid/EV Battery Voltage Sensor "C" Circuit Short to Ground or Open | ||
| P0B4A14 | Hybrid/EV Battery Voltage Sensor "D" Circuit Short to Ground or Open | ||
| P0B4F14 | Hybrid/EV Battery Voltage Sensor "E" Circuit Short to Ground or Open | ||
| P0B5414 | Hybrid/EV Battery Voltage Sensor "F" Circuit Short to Ground or Open | ||
| P0B5914 | Hybrid/EV Battery Voltage Sensor "G" Circuit Short to Ground or Open | ||
| P0B5E14 | Hybrid/EV Battery Voltage Sensor "H" Circuit Short to Ground or Open | ||
| P0B6314 | Hybrid/EV Battery Voltage Sensor "I" Circuit Short to Ground or Open | ||
| P0B6814 | Hybrid/EV Battery Voltage Sensor "J" Circuit Short to Ground or Open | ||
| P308A13 | Hybrid/EV Battery Voltage Sensor All Circuit Open | ||
| P0AFC62 | Hybrid/EV Battery Sensor Module Signal Compare Failure | ||
| P308A12 | Hybrid/EV Battery Voltage Sensor All Circuit Short to Auxiliary Battery | ||
| System malfunction | Motor generator control system | P0E3116 | DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold |
| P0E3117 | DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold | ||
P1C2D62 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Turn the power switch off.
A
B
C
D
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
E
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Apply the parking brake and secure the wheels using chocks.
Connect the GTS to the DLC3. *1
Turn the power switch on (READY). *2
Enter the following menus: Powertrain / Hybrid Control / Data List. *3
If the value of "Hybrid Battery SOC" is less than 55%, select drive (D) and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more. *4
| Tester Display |
|---|
| Hybrid Battery SOC |
Push the P position switch (transmission shift main switch) to select park (P). *5
Set the air conditioning to MAX COOL and turn the headlights on. *6
Confirm that "Hybrid Battery Current" is more than 3 A. *7
| Tester Display |
|---|
| Hybrid Battery Current |
With the engine stopped and the conditions of steps *5, *6 and *7 satisfied, leave the vehicle for 15 seconds. *8
Enter the following menus: Powertrain / Hybrid Control / Trouble codes. *9
Check for DTCs. *10
If the low HV battery information comes on, move the shift lever to P and start the engine to charge the HV battery. After the engine stops, perform steps *1 through *10 again.
| Result | Proceed to |
|---|---|
| No DTCs are output, or DTCs except the following are output. | A |
| P0E311C or P0CA300 are output. | B |
| P0B231C or P1C8349 are output. | C |
| P300000 is output. | D |
Turn the power switch off.
A
B
C
D
Turn the power switch on (READY). *11
Perform a road test that repeats full acceleration to 60 km/h (37 mph) and then braking to a complete stop three times. *12
Perform this road test only in an appropriate safe location, in accordance with all local laws.
This road test is performed to drive the car under high load and cause a change in the HV battery voltage.
Connect the GTS to the DLC3. *13
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. *14
Check for DTCs. *15
| Result | Proceed to |
|---|---|
| No DTCs are output, or DTCs except the following are output. | A |
| P0E311C or P0CA300 are output. | B |
| P0B231C or P1C8349 are output. | C |
| P300000 is output. | D |
Turn the power switch off.
A
B
C
D
Apply the parking brake and secure the wheels using chocks.
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Data List.
| Tester Display |
|---|
| Hybrid Battery SOC |
If the value of "Hybrid Battery SOC" is less than 55%, select drive (D) and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more. *4
Release the accelerator pedal, push the P position switch to select park (P) and wait for the engine to stop. Read the Data List when the engine stops.
If the engine starts, wait until it stops before continuing.
| Tester Display |
|---|
| VL-Voltage before Boosting |
| VH-Voltage after Boosting |
| Hybrid Battery Voltage |
| Result | Proceed to |
|---|---|
| Both of the following are not satisfied. | A |
| Both of the following are satisfied:
·
Difference between "Hybrid Battery Voltage" and "VH-Voltage after Boosting" is less than 5 V. ·
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is more than 30 V. |
B |
| Both of the following are satisfied:
·
Difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is less than 5 V. ·
Difference between "Hybrid Battery Voltage" and "VH-Voltage after Boosting" is more than 15 V. |
C |
Turn the power switch off.
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data of DTC P1C2D62.
| Result | Proceed to |
|---|---|
| Both of the following are satisfied or both of the following are not satisfied. | A |
| "VL-Voltage before Boosting" is less than 168 V or more than 280 V. | B |
| "Hybrid Battery Voltage" is less than 168 V or more than 280 V. | C |
Turn the power switch off.
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data of DTC P1C2D62.
In the freeze frame data, read the item "Hybrid Battery Voltage" and all of the "Hybrid Battery Block 1 to 9 Voltage".
| Result | Proceed to |
|---|---|
| Freeze frame data is not stored. | A |
| Both of the following are satisfied:
·
Sum of all "Hybrid Battery Block 1 to 9 Voltage" is more than ("Hybrid Battery Voltage" -40 V) ·
Sum of all "Hybrid Battery Block 1 to 9 Voltage" is less than ("Hybrid Battery Voltage" +25 V) |
B |
| Neither A nor B is satisfied. | C |
Turn the power switch off.
A
B
C
Apply the parking brake and secure the wheels using chocks.
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Data List.
If the value of "Hybrid Battery SOC" is less than 55%, select drive (D) and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more. *4
| Tester Display |
|---|
| Hybrid Battery SOC |
Release the accelerator pedal, push the P position switch to select park (P) and wait for the engine to stop. Read the Data List when the engine stops.
If the engine starts, wait until it stops before continuing.
| Tester Display |
|---|
| Hybrid Battery Voltage |
| Hybrid Battery Block 1 Voltage |
| Hybrid Battery Block 2 Voltage |
| Hybrid Battery Block 3 Voltage |
| Hybrid Battery Block 4 Voltage |
| Hybrid Battery Block 5 Voltage |
| Hybrid Battery Block 6 Voltage |
| Hybrid Battery Block 7 Voltage |
| Hybrid Battery Block 8 Voltage |
| Hybrid Battery Block 9 Voltage |
| Result | Proceed to |
|---|---|
| Both of the following are satisfied:
·
Sum of all "Hybrid Battery Block 1 to 9 Voltage" is more than ("Power Resource VB" -40 V) ·
Sum of all "Hybrid Battery Block 1 to 9 Voltage" is less than ("Power Resource VB" +25 V) |
A |
| The preceding condition is not satisfied. | B |
Turn the power switch off.
A
B