The hybrid vehicle control ECU alerts the driver and performs fail-safe control based on error signals received from the battery voltage sensor.
This DTC is stored if the HV battery is discharged excessively or the hybrid control system malfunctions.
If the HV battery voltage has dropped due to a malfunction in other components such as the inverter with converter assembly or the hybrid vehicle transaxle assembly, recharging the HV battery will be able to restore the voltage. If the HV battery voltage has dropped excessively after the vehicle was left for a long time, the HV battery will need to be replaced.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P300016 | Hybrid/EV Battery Control System Circuit Voltage Below Threshold | Malfunction is received from the battery voltage sensor:
Voltage of a battery block drops drastically. (1 trip detection logic) |
·
Engine ·
Hybrid vehicle transaxle assembly ·
HV battery |
Does not come on | Master Warning Light:
Comes on |
| DTC No. | Data List |
|---|---|
| P300016 | ·
Hybrid Battery Block 1 to 9 Voltage ·
Hybrid Battery SOC ·
Hybrid Battery Voltage ·
Hybrid Battery Current ·
Engine Speed |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Turn the power switch on (READY) with park (P) selected.
Wait until the engine starts and then stops.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
Thoroughly interview the customer as DTC P300016 may be stored if the SOC drops due to the vehicle being left with neutral (N) selected for a long time or running out of fuel.
When the engine cannot be started, DTC P300016 may be stored because the HV battery cannot be charged.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Proceed to |
|---|
| P300016 or P300000 only is output. |
| DTCs other than P300016 or P300000 are also output. |
If the HV battery voltage has dropped due to a malfunction in other components such as the inverter with converter assembly or the hybrid vehicle transaxle assembly, recharge the HV battery and then repair the malfunctioning part.
Turn the power switch off.
P300016 or P300000 only is output.
DTCs other than P300016 or P300000 are also output.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Engine / Trouble Codes.
Check for DTCs.
| Proceed to |
|---|
| No DTCs are output. |
| DTCs are output. |
Turn the power switch off.
No DTCs are output.
DTCs are output.
w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DIAGNOSTIC TROUBLE CODE CHART
w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DIAGNOSTIC TROUBLE CODE CHART
Turn the power switch on (READY).
Check if the engine starts.
Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.
Depressing the accelerator pedal with park (P) selected will cause the engine to start.
| Proceed to |
|---|
| The engine does not start. |
| The engine starts. |
Turn the power switch off.
The engine does not start.
The engine starts.
Push the P position switch (transmission shift main switch) to select park (P).
Lift up the vehicle.
Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.
Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.
Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.
| Proceed to |
|---|
| The crankshaft rotates smoothly. |
| The crankshaft does not rotate smoothly. |
Lower the vehicle.
The crankshaft rotates smoothly.
The crankshaft does not rotate smoothly.
Turn the power switch off.
Wait 10 minutes or more.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1 to 9 Voltage.
| Tester Display |
|---|
| Hybrid Battery Block 1 Voltage |
| Hybrid Battery Block 2 Voltage |
| Hybrid Battery Block 3 Voltage |
| Hybrid Battery Block 4 Voltage |
| Hybrid Battery Block 5 Voltage |
| Hybrid Battery Block 6 Voltage |
| Hybrid Battery Block 7 Voltage |
| Hybrid Battery Block 8 Voltage |
| Hybrid Battery Block 9 Voltage |
Read the Data List.
| Result | Proceed to |
|---|---|
| Any of "Hybrid Battery Block 1, 2, 8, 9 Voltage" is 12.0 V or less, or any of "Hybrid Battery Block 3, 4, 5, 6, 7 Voltage" is 24.0 V or less | A |
| Other than above | B |
Turn the power switch off.
A
B
Lift up the vehicle.
Turn the power switch on (IG).
Depress the brake pedal and move the shift lever to select neutral (N).
Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.
Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch on (IG) before performing this inspection, to prevent the engine from starting.
Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.
| Proceed to |
|---|
| The crankshaft does not rotate smoothly. |
| The crankshaft rotates smoothly. |
Lower the vehicle.
Turn the power switch off.
The crankshaft does not rotate smoothly.
The crankshaft rotates smoothly.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch on (READY).
Check if the engine starts.
Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.
Depressing the accelerator pedal with park (P) selected will cause the engine to start.
| Proceed to |
|---|
| The engine does not start. |
| The engine starts. |
Turn the power switch off.
The engine does not start.
The engine starts.
Turn the power switch off.
Wait 10 minutes or more.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1 to 9 Voltage.
| Tester Display |
|---|
| Hybrid Battery Block 1 Voltage |
| Hybrid Battery Block 2 Voltage |
| Hybrid Battery Block 3 Voltage |
| Hybrid Battery Block 4 Voltage |
| Hybrid Battery Block 5 Voltage |
| Hybrid Battery Block 6 Voltage |
| Hybrid Battery Block 7 Voltage |
| Hybrid Battery Block 8 Voltage |
| Hybrid Battery Block 9 Voltage |
Read the Data List.
| Result | Proceed to |
|---|---|
| Any of "Hybrid Battery Block 1, 2, 8, 9 Voltage" is 12.0 V or less, or any of "Hybrid Battery Block 3, 4, 5, 6, 7 Voltage" is 24.0 V or less | A |
| Other than above | B |
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>HYBRID VEHICLE TRANSAXLE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch on (READY).
Check if the engine starts.
Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.
Depressing the accelerator pedal with park (P) selected will cause the engine to start.
| Proceed to |
|---|
| The engine does not start. |
| The engine starts. |
Turn the power switch off.
The engine does not start.
The engine starts.
Turn the power switch off.
Wait 10 minutes or more.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1 to 9 Voltage.
| Tester Display |
|---|
| Hybrid Battery Block 1 Voltage |
| Hybrid Battery Block 2 Voltage |
| Hybrid Battery Block 3 Voltage |
| Hybrid Battery Block 4 Voltage |
| Hybrid Battery Block 5 Voltage |
| Hybrid Battery Block 6 Voltage |
| Hybrid Battery Block 7 Voltage |
| Hybrid Battery Block 8 Voltage |
| Hybrid Battery Block 9 Voltage |
Read the Data List.
| Result | Proceed to |
|---|---|
| Any of "Hybrid Battery Block 1, 2, 8, 9 Voltage" is 12.0 V or less, or any of "Hybrid Battery Block 3, 4, 5, 6, 7 Voltage" is 24.0 V or less | A |
| Other than above | B |
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT