Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0244767 HV BATTERY A

HYBRID / BATTERY CONTROL  HV BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of HV battery Battery status info update HV battery status information cannot be updated (Click here)
Replacement of hybrid battery terminal block Perform high voltage fuse accumulated load history reset DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When the cable is disconnected from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

If the HV battery has been struck or dropped, replace it.

·

When connecting a connector to the HV battery, confirm that the connector is securely connected through the following:

- Push the connector until a click sound is heard.

- Visually check and confirm that the connector is securely connected by pulling on it.

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·

When performing repairs around the HV battery, such as using a tap, do not allow metal shavings to enter the HV battery.

·

Do not touch any high voltage wire harnesses, connectors or parts with bare hands.

·
A375894

Hold the areas shown in the illustration and lift the HV battery.

·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts or nuts of the HV battery.

·
A375892C03
0.646,0.781 0.708,0.365 0.708,0.365 0.896,0.365 false 0.958,0.302 1.271,0.5 0.313,0.198 10 false *a
*a Opening


Do not put your hands into the openings of the HV battery.

·

When removing/installing/moving the HV battery assembly, make sure not to tilt it more than 80°.

·

Do not climb on top of or stand on the HV battery.

·

Do not allow any foreign matter or water to enter the HV battery.

·

If any bolts, nuts or clips are dropped into the HV battery, make sure to remove them.



Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

Hide 55738D 5.REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

Hide 55735A 6.REMOVE WATER GUARD PLATE LH

Hide 55736D 7.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 12601B 9.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 82121 10.DISCONNECT ENGINE WIRE

Hide 13.INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:

Wear insulated gloves.


a.
A376294C04
2.063,1.417 2.313,1.615 0.25,0.198 10 true *a 1.875,0.5 2.125,0.698 0.25,0.198 10 true *b
*a Bolt (A)
*b Bolt (B)


Using a T25 "TORX" socket wrench, install the connector cover assembly to the inverter with converter assembly with the bolt (A).

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)

NOTICE:

Do not touch the waterproof seal of the connector cover assembly.



b.

Install the bolt (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12601B 15.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 55701J 16.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55736D 17.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 18.INSTALL WATER GUARD PLATE LH

Hide 55737B 19.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

Hide 55738D 20.INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

Hide 21.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 22.REMOVE REAR SEAT CUSHION ASSEMBLY

Hide 72693 23.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 24.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 25.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 26.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76973F 27.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 76971G 28.REMOVE REAR UNDER COVER

a.
A375869

Disengage the 2 clips.


b.

Disengage the 2 guides to remove the rear under cover from the rear seat cushion leg sub-assembly.


Hide 71033 29.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.
A375871

Remove the 6 bolts and rear seat cushion leg sub-assembly.


Hide G9230 30.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide G92N4A 31.REMOVE NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Wear insulated gloves.


a.
A375873C02
1.292,0.271 1.542,0.271 false 1.26,1.26 1.51,1.26 false 0.615,0.938 0.781,0.938 0.781,0.938 1.073,0.719 false 1.135,1.094 1.292,0.885 1.292,0.885 1.469,0.885 true 1.583,0.188 1.896,0.385 0.313,0.198 10 false *1 1.563,1.198 1.875,1.396 0.313,0.198 10 false *2 0.448,0.854 0.76,1.052 0.313,0.198 10 false *a 0.49,0.51 0.802,0.708 0.313,0.198 10 false *b 1.51,0.813 1.823,1.01 0.313,0.198 10 false *c
*1 Service Plug Grip
*2 Battery Cover Lock Striker
*a Projection
*b Turn
*c Button


Using the service plug grip, remove the battery cover lock striker.

HINT:

Insert the projection of the service plug grip and turn the button of the battery cover lock striker counterclockwise to release the lock.



b.

Remove the 3 bolts, 2 nuts and No. 1 HV battery cover panel RH from the HV battery.


Hide 821H1 32.DISCONNECT HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.


a.
A375877C02
1.906,1.26 2.406,1.26 true 2.427,1.167 2.688,1.365 0.26,0.198 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.


b.

Disconnect the shield ground from the HV battery.


Hide 82161 33.DISCONNECT FLOOR WIRE

CAUTION:

Wear insulated gloves.


a.
A375881

Disengage the clamp.


b.

Disconnect the electric vehicle battery plug assembly connector.


c.

Disconnect the HV battery junction block assembly connector.


Hide G92F1 34.REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT

a.
A375883

Remove the clip.


b.

Disengage the claw to remove the No. 1 hybrid battery exhaust duct from the HV battery.


Hide 82161 35.DISCONNECT FLOOR WIRE

CAUTION:

Wear insulated gloves.


a.
A375887

Disengage the clamp.


b.

Disconnect the battery voltage sensor connector.


Hide G9510 36.REMOVE HV BATTERY

CAUTION:

Wear insulated gloves.


a.
A378149

Remove the 5 bolts and HV battery from the vehicle.

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to remove it. When removing the HV battery, be careful not to damage the parts around it.

·

When removing the HV battery from the vehicle, do not allow it to contact the vehicle.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Insulate the disconnected terminals or connectors with insulating tape.

·

If the HV battery has been struck or dropped, replace it.




Hide G920L 37.REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A376709

Remove the 6 bolts, 5 nuts and upper No. 1 hybrid battery cover sub-assembly from the HV battery.


Hide G92Q1 38.REMOVE NO. 1 HV BATTERY SHIELD PANEL

Hide 89892A 39.REMOVE BATTERY VOLTAGE SENSOR

Hide G92Z2 40.REMOVE HYBRID BATTERY TERMINAL BLOCK

Hide G92Z0 41.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

Hide G920Q 42.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide G92D1 43.REMOVE NO. 1 HYBRID BATTERY INTAKE DUCT