Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Shut Down Signal Circuit  


DESCRIPTION

The cause of the malfunction may be a shutdown signal.

Check whether there is a shutdown signal +B short circuit.

Related Parts Check
Area Inspection
HSDN terminal Check that the HSDN terminal voltage decreases to check for an open or short circuit while READY OFF (IG ON).
Hybrid vehicle control ECU, inverter, wire harness Check for open or short circuit in hybrid vehicle control ECU, inverter and wire harness.

SYSTEM DESCRIPTION

Power supply to the motor is cut off due to a shutdown signal sent from the hybrid vehicle control ECU to the motor generator control ECU (MG ECU).

WIRING DIAGRAM

A306450E26
2.417,0.344 2.729,0.542 0.313,0.198 10 false 6 2.417,0.698 2.729,0.896 0.313,0.198 10 false 5 2.417,1.073 2.729,1.271 0.313,0.198 10 false 22 2.417,1.396 2.729,1.594 0.313,0.198 10 false 24 2.417,1.75 2.729,1.948 0.313,0.198 10 false 23 4.563,1.021 4.875,1.219 0.313,0.198 10 false 6 4.563,1.51 4.875,1.708 0.313,0.198 10 false 3 3.302,0.469 4.854,0.76 1.552,0.292 10 false from PCU FR Fuse *1 4.479,1.208 4.792,1.406 0.313,0.198 10 false A50 4.792,1.073 5.323,1.323 0.531,0.25 10 false HSDN 4.813,1.688 5.344,1.938 0.531,0.25 10 false E1 4.75,2.281 6.635,2.677 1.885,0.396 10 false Hybrid Vehicle Control ECU 1.948,1.083 2.479,1.333 0.531,0.25 10 false HSDN 2.052,0.792 2.583,1.042 0.531,0.25 10 false +B2 2.125,0.458 2.656,0.708 0.531,0.25 10 false +B 1.927,1.51 2.458,1.76 0.531,0.25 10 false GND1 1.927,1.844 2.458,2.094 0.531,0.25 10 false GND2 0.469,2.219 0.99,2.448 0.521,0.229 10 false C33 0.469,2.365 2.646,2.594 2.177,0.229 10 false Inverter with Converter Assembly 4.51,1.698 4.792,1.896 0.281,0.198 10 false F3 3.292,0.677 4.844,0.969 1.552,0.292 10 false from Inverter Battery *2 2.833,2.365 4.302,2.604 1.469,0.24 10 false *1: w/o Inverter Battery 2.823,2.552 4.271,2.781 1.448,0.229 10 false *2: w/ Inverter Battery

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK HYBRID VEHICLE CONTROL ECU
a.

Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

A365591C50
1.563,0.344 1.906,0.594 0.344,0.25 5.313,0.302 5.656,0.552 0.344,0.25 6.021,1.302 5.781,2.26 true 1.802,1.302 1.448,2.26 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.635,0.396 2.094,0.594 0.458,0.198 10 false A50 5.417,0.354 5.698,0.594 0.281,0.24 10 false F3 5.719,2.292 6.031,2.49 0.313,0.198 10 false E1 1.24,2.302 1.854,2.5 0.615,0.198 10 false HSDN
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A50-6 (HSDN) - F3-3 (E1) Power switch on (IG) Below 4.5 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

SHUTDOWN SIGNAL CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the C33 inverter with converter assembly connector.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL


c.

Disconnect the A50 hybrid vehicle control ECU connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A367816C11
0.073,3.385 0.438,3.635 0.365,0.25 0.167,1.219 0.531,1.469 0.365,0.25 2.646,0.49 1.979,1.146 true 1.719,1.51 2.198,2.135 true 2.635,2.688 2.458,3.385 true 1.698,3.51 1.917,4.24 true 1.844,0.49 1.844,1.135 true 1.552,3.521 1.229,4.25 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.125,2.479 0.438,2.677 0.313,0.198 10 false *b 0.24,1.281 0.698,1.479 0.458,0.198 10 false C33 0.146,3.448 0.604,3.646 0.458,0.198 10 false A50 1.74,0.281 2.354,0.479 0.615,0.198 10 false +B2 2.052,2.156 2.667,2.354 0.615,0.198 10 false HSDN 1.74,4.292 2.354,4.49 0.615,0.198 10 false HSDN 0.979,4.292 1.594,4.49 0.615,0.198 10 false MREL 2.573,0.292 3.188,0.49 0.615,0.198 10 false +B 2.531,2.49 3.146,2.688 0.615,0.198 10 false +B1
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C33-22 (HSDN) or A50-6 (HSDN) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU and inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for 2 minutes or more.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-22 (HSDN) - C33-6 (+B) Power switch off 10 kΩ or higher
C33-22 (HSDN) - C33-5 (+B2) Power switch off 10 kΩ or higher
A50-6 (HSDN) - A50-11 (+B1) Power switch off 10 kΩ or higher
A50-6 (HSDN) - A50-5 (MREL) Power switch off 10 kΩ or higher



j.

Reconnect the A50 hybrid vehicle control ECU connector.


k.

Reconnect the C33 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the C33 inverter with converter assembly connector.


c.
A365592C10
0.99,0.115 1.344,0.333 0.354,0.219 0.979,0.854 0.615,0.583 true 0.813,0.917 0.281,1.031 true 1.115,1.323 1.104,1.844 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.042,0.167 1.5,0.365 0.458,0.198 10 false C33 0.969,1.875 1.583,2.073 0.615,0.198 10 false HSDN 0.073,0.958 0.385,1.156 0.313,0.198 10 false +B 0.365,0.406 0.823,0.604 0.458,0.198 10 false +B2
*a Component without harness connected
(Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-22 (HSDN) - C33-6 (+B) Power switch off 10 kΩ or higher
C33-22 (HSDN) - C33-5 (+B2) Power switch off 10 kΩ or higher



d.

Reconnect the C33 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY