Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop. A
Automatic station search function stops on a station. B





A

2.CHECK OPTIONAL COMPONENTS

B

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

Result:
Result Proceed to
Optional components are not installed. A
Optional components are installed. B


NOTICE:

Do not remove optional components without the permission of the customer.




A

3.CHECK NAVIGATION RECEIVER ASSEMBLY

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E245523

Preparation for check

i.

Disconnect the antenna connector from the navigation receiver assembly.



b.

Check for noise

i.

Turn the power switch on (ACC) with the navigation receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.




Result:
Proceed to
OK
NG



OK

4.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

4.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Disconnect the RA navigation receiver assembly connector.


b.
E188455C09
0.479,0.958 1.01,1.25 0.531,0.292 1.521,1.094 1.115,1.448 false 0.115,0.083 0.292,0.25 0.177,0.167 10 *a 0.656,1.021 0.948,1.188 0.292,0.167 10 RA 0.802,1.469 1.198,1.635 0.396,0.167 10 ANT+
*a Component without harness connected
(Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - Body ground Power switch on (ACC)
Radio switch on and FM or AM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE ANTENNA CORD SUB-ASSEMBLY (for Radio Antenna)

NG

5.REPLACE ANTENNA CORD SUB-ASSEMBLY (for Radio Antenna)
a.

Replace the antenna cord sub-assembly (for radio antenna) with a new or known good one and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END

NG

6.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
6.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 2 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY
7.REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 3 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END

NG

8.REPLACE ROOF ANTENNA ASSEMBLY
8.REPLACE ROOF ANTENNA ASSEMBLY
a.

Replace the roof antenna assembly with a new or known good one and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ROOF ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END

NG