If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 2 speaker assembly | A |
| Front No. 1 speaker assembly | B |
| Rear speaker assembly | C |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
Disconnect the F60 stereo component amplifier assembly connector.
Disconnect the G4 and G5 front No. 2 speaker assembly connectors.
Measure the resistance between the stereo component amplifier assembly and each of the front No. 2 speaker assemblies to check for an open in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F60-13 (TWR+) - G4-4 | Always | Below 1 Ω |
| F60-28 (TWR-) - G4-3 | Always | Below 1 Ω |
| F60-10 (TWL+) - G5-4 | Always | Below 1 Ω |
| F60-25 (TWL-) - G5-3 | Always | Below 1 Ω |
Measure the resistance between the stereo component amplifier assembly or each of the front No. 2 speaker assemblies and body ground to check for a short in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F60-13 (TWR+) or G4-4 - Body ground | Always | 10 kΩ or higher |
| F60-28 (TWR-) or G4-3 - Body ground | Always | 10 kΩ or higher |
| F60-10 (TWL+) or G5-4 - Body ground | Always | 10 kΩ or higher |
| F60-25 (TWL-) or G5-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed.
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F60 stereo component amplifier assembly connector.
Disconnect the I1 and J1 front No. 1 speaker assembly connectors.
Measure the resistance between the stereo component amplifier assembly and each of the front No. 1 speaker assemblies to check for an open in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F60-15 (FR+) - I1-1 | Always | Below 1 Ω |
| F60-30 (FR-) - I1-2 | Always | Below 1 Ω |
| F60-8 (FL+) - J1-1 | Always | Below 1 Ω |
| F60-23 (FL-) - J1-2 | Always | Below 1 Ω |
Measure the resistance between the stereo component amplifier assembly or each of the front No. 1 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F60-15 (FR+) or I1-1 - Body ground | Always | 10 kΩ or higher |
| F60-30 (FR-) or I1-2 - Body ground | Always | 10 kΩ or higher |
| F60-8 (FL+) or J1-1 - Body ground | Always | 10 kΩ or higher |
| F60-23 (FL-) or J1-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F60 stereo component amplifier assembly connector.
Disconnect the K4 and L5 rear speaker assembly connectors.
Measure the resistance between the stereo component amplifier assembly and each of the rear speaker assemblies to check for an open in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F60-11 (RR+) - K4-1 | Always | Below 1 Ω |
| F60-26 (RR-) - K4-2 | Always | Below 1 Ω |
| F60-12 (RL+) - L5-1 | Always | Below 1 Ω |
| F60-27 (RL-) - L5-2 | Always | Below 1 Ω |
Measure the resistance between the stereo component amplifier assembly or each of the rear speaker assemblies and body ground to check for a short in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F60-11 (RR+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| F60-26 (RR-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| F60-12 (RL+) or L5-1 - Body ground | Always | 10 kΩ or higher |
| F60-27 (RL-) or L5-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
Check that the malfunction disappears when a new or known good rear speaker assembly is installed.
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG