Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The navigation receiver assembly and telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2 are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Telephone microphone assembly*1

·

Map light assembly (telephone microphone assembly)*2

·

Navigation receiver assembly

·

Harness or connector



*1: w/o Sliding Roof

*2: w/ Sliding Roof


WIRING DIAGRAM

E334503E01
1.167,0.594 1.781,0.792 0.615,0.198 10 false SNS2 1.146,1.396 1.76,1.594 0.615,0.198 10 false MCO- 5.594,0.594 6.208,0.792 0.615,0.198 10 false SNS2 5.604,1.406 6.219,1.604 0.615,0.198 10 false MIN- 1.688,0.333 2.042,0.531 0.354,0.198 10 false 3*1 1.615,0.5 1.969,0.698 0.354,0.198 10 false 14*2 1.615,1.292 1.969,1.49 0.354,0.198 10 false 15*2 1.688,1.125 2.042,1.323 0.354,0.198 10 false 4*1 5.417,0.5 5.771,0.698 0.354,0.198 10 false 6 5.344,1.281 5.698,1.479 0.354,0.198 10 false 19 0.292,1.75 0.646,1.948 0.354,0.198 10 false O2*1 0.292,2.313 0.646,2.51 0.354,0.198 10 false O4*2 0.302,1.917 2.531,2.125 2.229,0.208 10 false Telephone Microphone Assembly*1 5.24,1.74 5.594,1.938 0.354,0.198 10 false F92 5.24,1.906 7.146,2.115 1.906,0.208 10 false Navigation Receiver Assembly 4.792,2.948 6.167,3.177 1.375,0.229 10 false *1: w/o Sliding Roof 4.792,3.313 6.167,3.542 1.375,0.229 10 false *2: w/ Sliding Roof 0.292,2.5 3.896,2.719 3.604,0.219 10 false Map Light Assembly (Telephone Microphone Assembly)*2

PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
E289390C22
1.521,0.698 1.896,0.938 0.375,0.24 2.417,2.531 2.063,1.958 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.594,0.729 1.906,0.927 0.313,0.198 10 false F92 2.406,2.563 2.917,2.823 0.51,0.26 10 false MIN-
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/ Sliding Roof) A
OK (w/o Sliding Roof) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

B

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

C

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Disconnect the O4 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-6 (SNS2) - O4-14 (SNS2) Always Below 1 Ω
F92-19 (MIN-) - O4-15 (MCO-) Always Below 1 Ω
F92-6 (SNS2) or O4-14 (SNS2) - Body ground Always 10 kΩ or higher
F92-19 (MIN-) or O4-15 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E187117C67
2.031,1.698 1.885,1.375 false 1.604,1.688 1.771,1.375 false 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.021,1.719 2.635,1.917 0.615,0.198 10 false SNS2 1.281,1.708 1.896,1.906 0.615,0.198 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SNS2) - 15 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE MAP LIGHT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Disconnect the O2 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-6 (SNS2) - O2-3 (SNS2) Always Below 1 Ω
F92-19 (MIN-) - O2-4 (MCO-) Always Below 1 Ω
F92-6 (SNS2) or O2-3 (SNS2) - Body ground Always 10 kΩ or higher
F92-19 (MIN-) or O2-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT TELEPHONE MICROPHONE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.
E221776C03
1.375,1.583 1.625,1.229 false 2,1.583 1.792,1.24 false 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.073,1.604 1.479,1.802 0.406,0.198 10 false MCO- 1.979,1.615 2.385,1.813 0.406,0.198 10 false SNS2
*a Component without harness connected
(Telephone Microphone Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY