Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the meter circuit plate and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation receiver assembly stores this DTC when the difference between the speed information from the navigation antenna assembly and the SPD pulse received from the meter circuit plate becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the meter circuit plate. The signal is changed to a pulse signal at the transistor in the meter circuit plate. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



DTC No. Detection Item DTC Detection Condition Trouble Area
B15C2 Speed Signal Malfunction A difference between the GPS speed and SPD pulse is detected.
·

Navigation receiver assembly

·

Meter circuit plate

·

Harness or connector

·

No. 11 junction connector*1

·

No. 17 junction connector*2



*1: for LHD

*2: for RHD


WIRING DIAGRAM

E342182E01
1.531,2.115 1.99,2.313 0.458,0.198 10 false SPD 1.531,0.229 1.99,0.427 0.458,0.198 10 false SP1 1.927,0.208 2.385,0.406 0.458,0.198 10 false 11 1.917,2.104 2.375,2.302 0.458,0.198 10 false 19 1.542,4.958 2,5.156 0.458,0.198 10 false SPD 1.906,4.958 2.365,5.156 0.458,0.198 10 false 11 2.802,2.021 3.26,2.219 0.458,0.198 10 false 19 4.302,2.01 4.76,2.208 0.458,0.198 10 false 16 4.302,3.479 4.76,3.677 0.458,0.198 10 false 18 5.313,0.208 5.771,0.406 0.458,0.198 10 false 20 5.594,0.323 6.052,0.521 0.458,0.198 10 false SI 5.594,2.219 6.052,2.417 0.458,0.198 10 false +S 5.313,2.104 5.771,2.302 0.458,0.198 10 false 19 5.313,3.563 5.771,3.76 0.458,0.198 10 false 17 5.594,3.583 6.052,3.781 0.458,0.198 10 false SPD 5.615,4.938 6.073,5.135 0.458,0.198 10 false SPD 5.313,4.927 5.771,5.125 0.458,0.198 10 false 17 0.323,0.844 0.781,1.042 0.458,0.198 10 false A41 0.302,1.01 2.375,1.427 2.073,0.417 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.417,2.521 2.208,2.948 1.792,0.427 10 false Certification ECU (Smart Key ECU Assembly) 0.438,2.365 0.896,2.563 0.458,0.198 10 false F1 0.417,5.208 0.875,5.406 0.458,0.198 10 false F61 0.406,5.375 2.208,5.729 1.802,0.354 10 false Stereo Component Amplifier Assembly*3 5.135,2.375 5.594,2.573 0.458,0.198 10 false F6 5.135,2.531 6.969,2.958 1.833,0.427 10 false Combination Meter Assembly (Meter Circuit Plate) 2.792,4.854 3.25,5.052 0.458,0.198 10 false 17 2.635,5.719 4.49,5.948 1.854,0.229 10 false No. 17 Junction Connector*5 5.073,3.844 5.531,4.042 0.458,0.198 10 false F92 5.323,5.396 7.042,5.865 1.719,0.469 10 false Radio and Display Receiver Assembly*2 5.073,4 7.156,4.208 2.083,0.208 10 false Navigation Receiver Assembly*1 5.031,5.396 5.49,5.594 0.458,0.198 10 false F31 2.667,6.125 4.75,6.333 2.083,0.208 10 false *2: for Radio and Display Type 0.344,6.115 2.427,6.323 2.083,0.208 10 false *1: for Navigation Receiver Type 3.99,2.01 4.448,2.208 0.458,0.198 10 false 7 3.958,3.479 4.417,3.677 0.458,0.198 10 false 10 2.427,2.021 2.885,2.219 0.458,0.198 10 false 11 2.469,4.854 2.656,5.094 0.188,0.24 10 false 9 4.271,2.208 4.729,2.406 0.458,0.198 10 false F85 4.271,3.677 4.729,3.875 0.458,0.198 10 false F85 2.76,2.219 3.219,2.417 0.458,0.198 10 false F85 2.75,5.063 3.208,5.26 0.458,0.198 10 false F85 3.906,2.208 4.177,2.417 0.271,0.208 10 false F79 3.917,3.677 4.188,3.885 0.271,0.208 10 false F79 2.385,2.219 2.656,2.427 0.271,0.208 10 false F79 2.396,5.063 2.667,5.271 0.271,0.208 10 false F79 2.646,5.438 4.5,5.667 1.854,0.229 10 false No. 8 Junction Connector*4 4.854,6.146 6.104,6.333 1.25,0.188 10 false *3: for 10 Speakers 1.677,6.469 2.542,6.677 0.865,0.208 10 false *5: for RHD 0.354,6.458 1.219,6.667 0.865,0.208 10 false *4: for LHD 2.438,2.417 2.615,2.625 0.177,0.208 10 false *4 2.438,5.271 2.615,5.479 0.177,0.208 10 false *4 3.948,2.406 4.125,2.615 0.177,0.208 10 false *4 3.958,3.885 4.135,4.094 0.177,0.208 10 false *4 2.792,2.427 2.969,2.635 0.177,0.208 10 false *5 4.313,2.417 4.49,2.625 0.177,0.208 10 false *5 4.313,3.885 4.49,4.094 0.177,0.208 10 false *5 2.802,5.271 2.979,5.479 0.177,0.208 10 false *5

PROCEDURE

1.CHECK SYSTEM SENSORS (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen. Refer to Check System Sensors in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>OPERATION CHECK


b.

While driving the vehicle, compare the value of "Speed" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The meter circuit plate receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "System Sensors Check" screen is almost the same as the actual vehicle speed measured using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT METER CIRCUIT PLATE (OUTPUT WAVEFORM)
2.INSPECT METER CIRCUIT PLATE (OUTPUT WAVEFORM)
a.
E256135C55
1.479,0.438 1.896,0.656 0.417,0.219 0.667,1.906 0.854,1.354 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.604,0.458 1.917,0.656 0.313,0.198 10 false F6 0.542,1.917 0.854,2.115 0.313,0.198 10 false +S 2.781,3.573 3.177,3.844 0.396,0.271 10 false GND 1.125,3.875 1.521,4.146 0.396,0.271 10 false A
*a Component with harness connected
(Meter Circuit Plate)


Check the output waveform.

i.

Remove the meter circuit plate with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F6-19 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F6-19 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.
E277606C29
1.552,0.219 1.969,0.51 0.417,0.292 2.667,2.052 2.406,1.469 false 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 1.646,0.271 2.146,0.563 0.5,0.292 10 false F92 2.625,2.094 3.073,2.396 0.448,0.302 10 false SPD 2.979,3.729 3.427,4.031 0.448,0.302 10 false GND 1.26,4.01 1.708,4.313 0.448,0.302 10 false A
*a Component with harness connected
(Navigation Receiver Assembly)


Check the input waveform.

i.

Remove the navigation receiver assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F92-17 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F92-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)

C

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-17 (SPD) - F79-10 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the F6 meter circuit plate connector.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-19 (+S) - F79-7 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE NO. 11 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR)
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Disconnect the F85 No. 17 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-17 (SPD) - F85-18 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 17 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 17 JUNCTION CONNECTOR)
a.

Disconnect the F6 meter circuit plate connector.


b.

Disconnect the F85 No. 17 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-19 (+S) - F85-16 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE NO. 17 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR