Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B1324  Lost Communication with Meter  B1325  Lost Communication with HUD  


DESCRIPTION

These DTCs are stored when communication between the navigation receiver assembly and meter circuit plate or combination meter mirror ECU* is not possible.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the navigation receiver assembly receives a registration information signal, which is sent by the meter circuit plate when the power switch is turned on (IG), 1 or more times, the navigation receiver assembly does not receive the signal for 30 seconds or more
·

Local bus communication line

·

Meter circuit plate power source circuit

·

Meter circuit plate

·

Navigation receiver assembly

·

Harness or connector


B1325 Lost Communication with HUD After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter mirror ECU when the power switch is turned on (IG), 1 or more times, the navigation receiver assembly does not receive the signal for 30 seconds or more*
·

Local bus communication line

·

Combination meter mirror ECU power source circuit

·

Combination meter mirror ECU

·

Navigation receiver assembly

·

Harness or connector



*: w/ Headup Display System


HINT:

The navigation receiver assembly is the master unit.


WIRING DIAGRAM

for LHD
E334502E09
5.969,0.552 6.583,0.75 0.615,0.198 10 false CNH1 5.969,0.844 6.583,1.042 0.615,0.198 10 false CNL1 5.802,1.167 6.417,1.365 0.615,0.198 10 false F95 5.802,1.323 7,1.688 1.198,0.365 10 false Navigation Receiver Assembly 5.792,0.417 6.063,0.604 0.271,0.188 10 false 3 5.792,0.708 6.063,0.896 0.271,0.188 10 false 4 5.417,0.417 5.688,0.604 0.271,0.188 10 false 2 5.396,0.708 5.667,0.896 0.271,0.188 10 false 13 4.25,0.417 4.521,0.604 0.271,0.188 10 false 1 4.188,0.708 4.458,0.896 0.271,0.188 10 false 12 4.25,2.438 4.521,2.625 0.271,0.188 10 false 3 4.188,2.729 4.458,2.917 0.271,0.188 10 false 14 3.865,0.417 4.135,0.604 0.271,0.188 10 false 33 3.865,0.708 4.135,0.896 0.271,0.188 10 false 34 3.865,1.01 4.135,1.198 0.271,0.188 10 false 28 2.688,0.448 2.958,0.635 0.271,0.188 10 false 22 2.688,0.865 2.958,1.052 0.271,0.188 10 false 21 3.865,2.438 4.135,2.625 0.271,0.188 10 false 7 3.865,2.729 4.135,2.917 0.271,0.188 10 false 8 3.865,3.042 4.135,3.229 0.271,0.188 10 false 6 2.75,2.469 3.021,2.656 0.271,0.188 10 false 1 2.75,2.896 3.021,3.083 0.271,0.188 10 false 2 2.76,3.458 3.375,3.656 0.615,0.198 10 false G7 2.76,3.615 3.938,4 1.177,0.385 10 false Combination Meter Mirror ECU* 4.365,3.469 4.979,3.667 0.615,0.198 10 false F79 4.365,3.635 6.083,3.865 1.719,0.229 10 false No. 11 Junction Connector 2.729,1.448 3.344,1.646 0.615,0.198 10 false F6 2.719,1.604 3.99,1.99 1.271,0.385 10 false Meter Circuit Plate 3.375,0.563 3.99,0.76 0.615,0.198 10 false MSCH 3.375,0.844 3.99,1.042 0.615,0.198 10 false MSCL 2.927,0.563 3.188,0.76 0.26,0.198 10 false B 2.927,0.99 3.229,1.188 0.302,0.198 10 false IG+ 3.563,1.115 3.865,1.313 0.302,0.198 10 false ES 3.438,2.583 4.052,2.781 0.615,0.198 10 false LCL+ 3.458,2.875 4.073,3.073 0.615,0.198 10 false LCL- 3.573,3.146 3.875,3.344 0.302,0.198 10 false ES 2.917,2.594 3.177,2.792 0.26,0.198 10 false B 2.927,3.01 3.229,3.208 0.302,0.198 10 false IG 1.708,0.698 2.781,0.906 1.073,0.208 10 false ECU-DCC NO. 2 1.708,2.719 2.781,2.927 1.073,0.208 10 false ECU-DCC NO. 2 1.833,1.115 2.594,1.313 0.76,0.198 10 false METER-IG2 1.729,3.146 2.698,3.333 0.969,0.188 10 false ECU-IG1 NO. 4 0.167,0.531 1.542,0.75 1.375,0.219 10 false from Auxiliary Battery 0.167,0.948 1.542,1.167 1.375,0.219 10 false from IG2-NO. 2 Relay 0.167,2.552 1.542,2.771 1.375,0.219 10 false from Auxiliary Battery 0.177,2.979 1.552,3.198 1.375,0.219 10 false from IG1-NO. 1 Relay 1,5.208 3.646,5.438 2.646,0.229 10 false : Local Bus Communication Line 0.948,4.833 2.802,5.052 1.854,0.219 10 false *: w/ Headup Display System

for RHD
E334502E10
5.969,0.552 6.583,0.75 0.615,0.198 10 false CNH1 5.969,0.844 6.583,1.042 0.615,0.198 10 false CNL1 5.802,1.167 6.417,1.365 0.615,0.198 10 false F95 5.802,1.323 7,1.688 1.198,0.365 10 false Navigation Receiver Assembly 5.792,0.417 6.063,0.604 0.271,0.188 10 false 3 5.792,0.708 6.063,0.896 0.271,0.188 10 false 4 5.417,0.417 5.688,0.604 0.271,0.188 10 false 5 5.396,0.708 5.667,0.896 0.271,0.188 10 false 16 4.25,0.417 4.521,0.604 0.271,0.188 10 false 7 4.188,0.708 4.458,0.896 0.271,0.188 10 false 18 4.25,2.438 4.521,2.625 0.271,0.188 10 false 6 4.188,2.729 4.458,2.917 0.271,0.188 10 false 17 3.865,0.417 4.135,0.604 0.271,0.188 10 false 33 3.865,0.708 4.135,0.896 0.271,0.188 10 false 34 3.865,1.01 4.135,1.198 0.271,0.188 10 false 28 2.688,0.448 2.958,0.635 0.271,0.188 10 false 22 2.688,0.865 2.958,1.052 0.271,0.188 10 false 21 3.865,2.438 4.135,2.625 0.271,0.188 10 false 7 3.865,2.729 4.135,2.917 0.271,0.188 10 false 8 3.865,3.042 4.135,3.229 0.271,0.188 10 false 6 2.75,2.469 3.021,2.656 0.271,0.188 10 false 1 2.75,2.896 3.021,3.083 0.271,0.188 10 false 2 2.76,3.458 3.375,3.656 0.615,0.198 10 false G7 2.76,3.615 3.938,4 1.177,0.385 10 false Combination Meter Mirror ECU* 4.365,3.469 4.979,3.667 0.615,0.198 10 false F77 4.365,3.635 6.083,3.865 1.719,0.229 10 false No. 9 Junction Connector 2.729,1.448 3.344,1.646 0.615,0.198 10 false F6 2.719,1.604 3.99,1.99 1.271,0.385 10 false Meter Circuit Plate 3.375,0.563 3.99,0.76 0.615,0.198 10 false MSCH 3.375,0.844 3.99,1.042 0.615,0.198 10 false MSCL 2.927,0.563 3.188,0.76 0.26,0.198 10 false B 2.927,0.99 3.229,1.188 0.302,0.198 10 false IG+ 3.563,1.115 3.865,1.313 0.302,0.198 10 false ES 3.438,2.583 4.052,2.781 0.615,0.198 10 false LCL+ 3.458,2.875 4.073,3.073 0.615,0.198 10 false LCL- 3.573,3.146 3.875,3.344 0.302,0.198 10 false ES 2.917,2.594 3.177,2.792 0.26,0.198 10 false B 2.927,3.01 3.229,3.208 0.302,0.198 10 false IG 1.708,0.698 2.781,0.906 1.073,0.208 10 false ECU-DCC NO. 2 1.708,2.719 2.781,2.927 1.073,0.208 10 false ECU-DCC NO. 2 1.833,1.115 2.594,1.313 0.76,0.198 10 false METER-IG2 1.729,3.146 2.698,3.333 0.969,0.188 10 false ECU-IG1 NO. 4 0.167,0.531 1.542,0.75 1.375,0.219 10 false from Auxiliary Battery 0.167,0.948 1.542,1.167 1.375,0.219 10 false from IG2-NO. 2 Relay 0.167,2.552 1.542,2.771 1.375,0.219 10 false from Auxiliary Battery 0.177,2.979 1.552,3.198 1.375,0.219 10 false from IG1-NO. 1 Relay 1,5.208 3.646,5.438 2.646,0.229 10 false : Local Bus Communication Line 0.948,4.833 2.802,5.052 1.854,0.219 10 false *: w/ Headup Display System

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for LHD A
for RHD B




A

2.CHECK DTC

B

22.CHECK DTC
2.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTC B1324 and B1325 are not output A
DTC B1324 and B1325 are output
(w/ Headup Display System)
B
DTC B1324 is output C
DTC B1325 is output
(w/ Headup Display System)
D



A

B

3.CHECK LOCAL BUS

C

12.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE POWER SOURCE)

D

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU POWER SOURCE)
3.CHECK LOCAL BUS
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (Below 54 Ω) B
NG (70 Ω or higher) C



A

B

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)

C

10.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the F95 navigation receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)

NG

9.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the F6 meter circuit plate connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-1 - F79-12 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)

NG

8.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the G7 combination meter mirror ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-3 - F79-14 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-3 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-14 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-3 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F79-14 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - G7-8 (LCL-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F6-34 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F95 navigation receiver assembly connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-3 (CNH1) - F95-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F95 navigation receiver assembly connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-3 (CNH1) - F95-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

11.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
11.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the F95 navigation receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE POWER SOURCE)
a.

Disconnect the F6 meter circuit plate connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-28 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-22 (B) - Body ground Power switch off 11 to 14 V
F6-21 (IG+) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the F6 meter circuit plate connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-1 - F79-12 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)

NG

16.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
14.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the F95 navigation receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

15.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
15.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F95 navigation receiver assembly connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-3 (CNH1) - F95-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F6-34 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU POWER SOURCE)
a.

Disconnect the G7 combination meter mirror ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-6 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-1 (B) - Body ground Power switch off 11 to 14 V
G7-2 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the G7 combination meter mirror ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-3 - F79-14 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-3 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-14 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-3 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F79-14 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)

NG

21.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
19.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the F95 navigation receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

20.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
20.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F95 navigation receiver assembly connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-3 (CNH1) - F95-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - G7-8 (LCL-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTC B1324 and B1325 are not output A
DTC B1324 and B1325 are output
(w/ Headup Display System)
B
DTC B1324 is output C
DTC B1325 is output
(w/ Headup Display System)
D



A

B

23.CHECK LOCAL BUS

C

32.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE POWER SOURCE)

D

37.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU POWER SOURCE)
23.CHECK LOCAL BUS
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (Below 54 Ω) B
NG (70 Ω or higher) C



A

B

24.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)

C

30.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
24.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the F95 navigation receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)

NG

29.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
25.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the F6 meter circuit plate connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-7 - F77-18 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)

NG

28.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
26.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the G7 combination meter mirror ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-6 - F77-17 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-6 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-17 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-6 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F77-17 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

27.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
27.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - G7-8 (LCL-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F6-34 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F95 navigation receiver assembly connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-3 (CNH1) - F95-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F95 navigation receiver assembly connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-3 (CNH1) - F95-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

31.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
31.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the F95 navigation receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE POWER SOURCE)
a.

Disconnect the F6 meter circuit plate connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-28 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-22 (B) - Body ground Power switch off 11 to 14 V
F6-21 (IG+) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

33.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the F6 meter circuit plate connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-7 - F77-18 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

34.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)

NG

36.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
34.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the F95 navigation receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

35.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
35.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F95 navigation receiver assembly connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-3 (CNH1) - F95-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F6-34 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU POWER SOURCE)
a.

Disconnect the G7 combination meter mirror ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-6 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-1 (B) - Body ground Power switch off 11 to 14 V
G7-2 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

38.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the G7 combination meter mirror ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-6 - F77-17 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-6 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-17 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-6 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F77-17 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

39.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)

NG

41.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
39.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the F95 navigation receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

40.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
40.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F95 navigation receiver assembly connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-3 (CNH1) - F95-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - G7-8 (LCL-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR