If the entry lock function does not operate for the driver door only, but the entry unlock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the lock sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door)).
The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to Precaution.
After repair, confirm that no DTCs are output.
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the power switch off.
Open and close the driver door.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.
Read the Data List according to the display on the GTS.
| *A | for LHD |
| *B | for RHD |
| *a | Lock Sensor |
Touch the lock sensor of the front door outside handle assembly (for driver door).
If the door does not lock even when touching the lock sensor, touch it with your palm.
When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Trigger Switch | Driver door touch sensor (lock sensor) | ON or OFF | ON: Driver door touch sensor (lock sensor) touched
OFF: Driver door touch sensor (lock sensor) not touched |
·
Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate. |
| Tester Display |
|---|
| D-Door Trigger Switch |
When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.*
*: w/o Double Locking System
The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M59 certification ECU (smart key ECU assembly) connector.
Disconnect the J3*1 or I3*2 front door outside handle assembly (for driver door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M59-17 (CLG1) - J3-6 (ANT1) | Always | Below 1 Ω |
| M59-16 (CG1B) - J3-4 (ANT2) | Always | Below 1 Ω |
| M59-17 (CLG1) or J3-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| M59-16 (CG1B) or J3-4 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M59-17 (CLG1) - I3-6 (ANT1) | Always | Below 1 Ω |
| M59-16 (CG1B) - I3-4 (ANT2) | Always | Below 1 Ω |
| M59-17 (CLG1) or I3-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| M59-16 (CG1B) or I3-4 (ANT2) - Body ground | Always | 10 kΩ or higher |
Reconnect the M59 certification ECU (smart key ECU assembly) connector.
Reconnect the J3*1 or I3*2 front door outside handle assembly (for driver door) connector.
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
*b | Waveform 1 |
| *c | Lock sensor not touched | *d | Lock sensor touched |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M59-17 (CLG1) - F1-18 (E) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) 5.
Driver door lock sensor touched |
5 V/DIV., 40 ms/DIV. | Pulse generation
(See waveform 1) |
*: For details about the entry function detection area, refer to Operation Check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG