CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| F1-18 (E) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| F1-4 (+B) - F1-18 (E) | Input | GR - W-B | Power supply | Power switch off | 11 to 14 V | - |
| F1-15 (CUTB) - F1-18 (E) | Input | W - W-B | Dark current cut pin* | Power switch off | 11 to 14 V | - |
*: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).
Reconnect the F1 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| F1-17 (IG1D) - F1-18 (E) | Output | L - W-B | IG power supply | Power switch off → on (IG) | Below 1 V → 10 V or higher | - |
| M59-17 (CLG1) - F1-18 (E) | Output | G - W-B | Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
Pulse generation
(See waveform 1) |
Overhead + Driver Side (key diagnostic mode) |
| Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
Pulse generation
(See waveform 2) |
|||||
| M59-17 (CLG1) - F1-18 (E) | Input | G - W-B | Input to driver door lock sensor
(front door outside handle assembly (for driver door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly)) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) 5.
Driver door lock sensor touched |
Pulse generation
(See waveform 3) |
D-Door Trigger Switch |
| M59-17 (CLG1) - F1-18 (E) | Input | G - W-B | Input to driver door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly)) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not near the vehicle 5.
Driver door unlock sensor touched |
Pulse generation
(See waveform 4) |
D-Door Touch Sensor |
| M59-16 (CG1B) - F1-18 (E) | Output | R - W-B | Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) | Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
Pulse generation
(See waveform 5) |
Overhead + Driver Side (key diagnostic mode) |
| Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
Pulse generation
(See waveform 6) |
|||||
| M59-15 (CLG2) - F1-18 (E) | Output | G - W-B | Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
Pulse generation
(See waveform 1) |
Overhead + Passenger Side (key diagnostic mode) |
| Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
Pulse generation
(See waveform 2) |
|||||
| M59-15 (CLG2) - F1-18 (E) | Input | G - W-B | Input to front passenger door lock sensor
(front door outside handle assembly (for front passenger door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly)) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) 5.
Front passenger door lock sensor touched |
Pulse generation
(See waveform 3) |
P-Door Trigger Switch |
| M59-15 (CLG2) - F1-18 (E) | Input | G - W-B | Input to front passenger door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly)) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not near the vehicle 5.
Front passenger door unlock sensor touched |
Pulse generation
(See waveform 4) |
P-Door Touch Sensor |
| M59-14 (CG2B) - F1-18 (E) | Output | R - W-B | Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) | Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
Pulse generation
(See waveform 5) |
Overhead + Passenger Side (key diagnostic mode) |
| Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
Pulse generation
(See waveform 6) |
|||||
| F1-8 (CLG5) - F1-18 (E) | Output | SB - W-B | Output to No. 1 indoor electrical key antenna assembly (front floor) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 7) |
Overhead + Front Room (key diagnostic mode) |
| F1-9 (CG5B) - F1-18 (E) | Output | GR - W-B | Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 7) |
Overhead + Front Room (key diagnostic mode) |
| M59-5 (CLG6) - F1-18 (E) | Output | GR - W-B | Output to No. 2 indoor electrical key antenna assembly (rear floor) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 7) |
Overhead + Rear Room (key diagnostic mode) |
| M59-6 (CG6B) - F1-18 (E) | Output | BR - W-B | Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 7) |
Overhead + Rear Room (key diagnostic mode) |
| M59-11 (CLG7) - F1-18 (E) | Output | G - W-B | Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 7) |
Overhead + Back Door (inside) (key diagnostic mode) |
| M59-10 (CG7B) - F1-18 (E) | Output | R - W-B | Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 7) |
Overhead + Back Door (inside) (key diagnostic mode) |
| M59-13 (CLG8) - F1-18 (E) | Output | BE - W-B | Output to electrical key antenna (outside luggage compartment) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Back door opener switch assembly off → on |
Pulse generation
(See waveform 8) |
Overhead + Back Door (key diagnostic mode) |
| M59-12 (CG8B) - F1-18 (E) | Output | W - W-B | Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG8 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Back door opener switch assembly off → on |
Pulse generation
(See waveform 8) |
Overhead + Back Door (key diagnostic mode) |
| M59-26 (TSW5) - F1-18 (E) | Input | B - W-B | Back door opener switch assembly (open switch) signal input | Back door opener switch assembly (open switch) off → on | Pulse generation
(See waveform 9) |
Tr/B-Door Unlock SW |
| M59-27 (TSW6) - F1-18 (E) | Input | GR - W-B | Back door opener switch assembly (lock switch) signal input | Back door opener switch assembly (lock switch) off → on | Pulse generation
(See waveform 9) |
Tr/B-Door Lock SW |
| M59-18 (RCO) - F1-18 (E) | Output | G - W-B | Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation
(See waveform 10) |
- |
| M59-19 (RDAM) - F1-18 (E) | Input | P - W-B | Door control receiver verifies data received from electrical key transmitter sub-assembly.
Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)). |
Proceed:
1.
Power switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation
(See waveform 11) |
- |
| M59-20 (CSEL) - F1-18 (E) | Output | V - W-B | Communication channel switching circuit | Procedure:
1.
Power switch off 2.
All doors closed |
Below 1 V → pulse generation | - |
*: For details about the entry function detection area, refer to Operation Check.
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-17 (CLG1) - F1-18 (E)
M59-15 (CLG2) - F1-18 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
*: For details about the entry function detection area, refer to Operation Check.
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-17 (CLG1) - F1-18 (E)
M59-15 (CLG2) - F1-18 (E) |
| Tool Setting | 5 V/DIV., 100 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
*: For details about the entry function detection area, refer to Operation Check.
| *a | Lock sensor not touched |
| *b | Lock sensor touched |
Using an oscilloscope, check waveform 3.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-17 (CLG1) - F1-18 (E)
M59-15 (CLG2) - F1-18 (E) |
| Tool Setting | 5 V/DIV., 40 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) 5.
Lock sensor not touched → touched |
*: For details about the entry function detection area, refer to Operation Check.
| *a | Unlock sensor not touched |
| *b | Unlock sensor touched |
Using an oscilloscope, check waveform 4.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-17 (CLG1) - F1-18 (E)
M59-15 (CLG2) - F1-18 (E) |
| Tool Setting | 5 V/DIV., 50 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not near the vehicle 5.
Unlock sensor not touched → touched |
Using an oscilloscope, check waveform 5.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-16 (CG1B) - F1-18 (E)
M59-14 (CG2B) - F1-18 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
*: For details about the entry function detection area, refer to Operation Check.
Using an oscilloscope, check waveform 6.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-16 (CG1B) - F1-18 (E)
M59-14 (CG2B) - F1-18 (E) |
| Tool Setting | 5 V/DIV., 100 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
*: For details about the entry function detection area, refer to Operation Check.
| *a | For 30 seconds after any door closed |
| *b | After 30 seconds or more have elapsed since any door closed |
Using an oscilloscope, check waveform 7.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | F1-8 (CLG5) - F1-18 (E)
F1-9 (CG5B) - F1-18 (E) M59-5 (CLG6) - F1-18 (E) M59-6 (CG6B) - F1-18 (E) M59-11 (CLG7) - F1-18 (E) M59-10 (CG7B) - F1-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Using an oscilloscope, check waveform 8.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-13 (CLG8) - F1-18 (E)
M59-12 (CG8B) - F1-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Back door opener switch assembly off → on |
| *a | Checking for switch on signal at short intervals |
Using an oscilloscope, check waveform 9.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-26 (TSW5) - F1-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Back door opener switch assembly (open switch) off → on |
| Item | Content |
|---|---|
| Tester Connection | M59-27 (TSW6) - F1-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Back door opener switch assembly (lock switch) off → on |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 10.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-18 (RCO) - F1-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 11.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | M59-19 (RDAM) - F1-18 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Reconnect the instrument panel junction block assembly connectors.
Measure the resistance and voltage according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| MB-11 (GND1) - Body ground | - | - | Ground | Always | Below 1 Ω | - |
| MB-31 (BECU) - Body ground | Input | - | Auxiliary battery power supply (for CPU) | Power switch off | 11 to 14 V | - |
| F17-6 (FLCY) - Body ground | Input | BR - Body ground | Front door courtesy light switch assembly (for LH) input | Front door LH closed | 10 kΩ or higher | FL Door Courtesy SW |
| Front door LH open | Below 1 Ω | |||||
| F17-27 (FRCY) - Body ground | Input | L - Body ground | Front door courtesy light switch assembly (for RH) input | Front door RH closed | 10 kΩ or higher | FR Door Courtesy SW |
| Front door RH open | Below 1 Ω | |||||
| MB-13 (LCTY) - Body ground | Input | - | Rear door courtesy light switch assembly (for LH) input | Rear door LH closed | 10 kΩ or higher | RL Door Courtesy SW |
| Rear door LH open | Below 1 Ω | |||||
| MB-2 (RCTY) - Body ground | Input | - | Rear door courtesy light switch assembly (for RH) input | Rear door RH closed | 10 kΩ or higher | RR Door Courtesy SW |
| Rear door RH open | Below 1 Ω | |||||
| MB-4 (BCTY) - Body ground | Input | - | Back door courtesy light switch input | Back door closed | 10 kΩ or higher | Back Door Courtesy SW |
| Back door open | Below 1 Ω |
Install the main body ECU (multiplex network body ECU) to instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| 3D-13 (LSFL) - Body ground | Input | GR - Body ground | Front door LH unlock detection switch input | Front door LH locked → unlocked | Pulse generation
(See waveform 1) |
FL Door Lock Pos |
| 3D-12 (LSFR) - Body ground | Input | V - Body ground | Front door RH unlock detection switch input | Front door RH locked → unlocked | Pulse generation
(See waveform 1) |
FR Door Lock Pos |
| 3D-14 (LSR) - Body ground | Input | LG - Body ground | Rear door LH unlock detection switch input | Rear door LH and RH locked → Rear door LH or RH unlocked | Pulse generation
(See waveform 1) |
RL-Door Lock Pos SW |
| 3D-14 (LSR) - Body ground | Input | LG - Body ground | Rear door RH unlock detection switch input | Rear door RH and LH locked → Rear door RH or LH unlocked | Pulse generation
(See waveform 1) |
RR-Door Lock Pos SW |
| F17-6 (FLCY) - Body ground | Input | BR - Body ground | Front door LH courtesy light switch input | Front door LH closed → open | Pulse generation
(See waveform 2) |
FL Door Courtesy SW |
| F17-27 (FRCY) - Body ground | Input | L - Body ground | Front door RH courtesy light switch input | Front door RH closed → open | Pulse generation
(See waveform 2) |
FR Door Courtesy SW |
| 3H-24 (LCTY) - Body ground | Input | BR - Body ground | Rear door LH courtesy light switch input | Rear door LH closed → open | Pulse generation
(See waveform 2) |
RL Door Courtesy SW |
| 3A-31 (RCTY) - Body ground | Input | GR - Body ground | Rear door RH courtesy light switch input | Rear door RH closed → open | Pulse generation
(See waveform 2) |
RR Door Courtesy SW |
| 3H-34 (BCTY) - Body ground | Input | B - Body ground | Back door courtesy light switch input | Back door closed → opened | Pulse generation
(See waveform 2) |
Back Door Courtesy SW |
| 3F-29 (BZR) - Body ground | Output | R - Body ground | Wireless buzzer signal output | Procedure:
1.
Power switch off 2.
All doors closed 3.
Lock switch of electrical key transmitter sub-assembly not pressed → pressed |
Below 1 V → pulse generation | - |
| *a | Door locked |
| *b | Door unlocked |
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | 3D-13 (LSFL) - Body ground
3D-12 (LSFR) - Body ground 3D-14 (LSR) - Body ground |
| Tool Setting | 2 V/DIV., 200 ms/DIV. |
| Condition | Door locked → unlocked |
| *a | Door closed |
| *b | Door open |
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | F17-6 (FLCY) - Body ground
F17-27 (FRCY) - Body ground 3H-24 (LCTY) - Body ground 3A-31 (RCTY) - Body ground 3H-34 (BCTY) - Body ground |
| Tool Setting | 2 V/DIV., 200 ms/DIV. |
| Condition | Door closed → opened |