The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition using 2 circuits (GL1, GL2).
The skid control ECU (brake booster with master cylinder assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via CAN communication.
If there are malfunctions in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) will be stored.
If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.
These DTCs (C1210 and C1336) will also be stored when zero point calibration has not been completed.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1210 | Zero Point Calibration of Yaw Rate Sensor Undone | 1139 | Yaw rate sensor zero point calibration is incomplete. | ·
Yaw rate sensor (airbag ECU assembly) installed improperly ·
Yaw rate sensor (airbag ECU assembly) ·
Skid control ECU (brake booster with master cylinder assembly) |
VSC DTC |
| C1336 | Zero Point Calibration of Acceleration Sensor Undone | 1138 | Acceleration sensor zero point calibration is incomplete. | ·
Acceleration sensor (airbag ECU assembly) installed improperly ·
Acceleration sensor (airbag ECU assembly) ·
Skid control ECU (brake booster with master cylinder assembly) |
ABS DTC |
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
After replacing or reinstalling the yaw rate and acceleration sensor (airbag ECU assembly), perform yaw rate and acceleration sensor zero point calibration after clearing previously calibrated data.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION
When U0124 is output together with C1210 and/or C1336, inspect and repair trouble areas indicated by U0124 first.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073
Perform zero point calibration of the yaw rate and acceleration sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION
Make sure to perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization after performing "Reset Memory" as the data stored during linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization is cleared.
| Tester Display |
|---|
| Reset Memory |
| Tester Display |
|---|
| Test Mode |
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform a Test Mode (Signal Check) inspection sensor check and check that all Test Mode (Signal Check) inspection items change from incomplete to complete.
| Tester Display |
|---|
| Signal Check |
All Test Mode (Signal Check) inspection items change from incomplete to complete
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Check that the yaw rate and acceleration sensor (airbag ECU assembly) has been installed properly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
The yaw rate and acceleration sensor (airbag ECU assembly) is tightened to the specified torque.
The yaw rate and acceleration sensor (airbag ECU assembly) is not tilted.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Deceleration Sensor | Acceleration sensor 1 | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Deceleration Sensor2 | Acceleration sensor 2 | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Yaw Rate Sensor | Yaw rate sensor 1 | Min.: -128 degrees/s, Max.: 127 degrees/s | Vehicle stationary: 0 degrees/s
Turning right: -128 to 0 degrees/s Turning left: 0 to 127 degrees/s |
- |
| Yaw Rate Sensor2 | Yaw rate sensor 2 | Min.: -128 degrees/s, Max.: 127 degrees/s | Vehicle stationary: 0 degrees/s
Turning right: -128 to 0 degrees/s Turning left: 0 to 127 degrees/s |
- |
| Tester Display |
|---|
| Deceleration Sensor |
| Deceleration Sensor2 |
| Yaw Rate Sensor |
| Yaw Rate Sensor2 |
Check the yaw rate and acceleration sensor (airbag ECU assembly) output value displayed on the GTS.
The yaw rate and acceleration sensor (airbag ECU assembly) output value is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL
NG