Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1256  Accumulator Low Pressure  


DESCRIPTION

The accumulator pressure sensor is built into the brake actuator (brake booster with master cylinder assembly) and detects the accumulator pressure.

The skid control ECU (brake booster with master cylinder assembly) turns on the brake warning light / red (malfunction) and brake warning light / yellow (minor malfunction), and sounds the meter buzzer if it senses a decrease in the accumulator pressure.

DTC C1256 may be stored if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1256 Accumulator Low Pressure 341
1125
Significant drop in accumulator pressure continues.
(DTCs will be stored and the buzzer will operate when either condition is met.)
·

Accumulator pressure dropped due to frequent brake pedal operation (not a malfunction)

·

Pump motor malfunction

·

Accumulator deterioration

·

Accumulator pressure sensor (brake booster with master cylinder assembly)

·

Supply voltage reduced


Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1256 is output. A
DTCs C1202, C1241, C1252, C1253 and/or C1391 are output. B



A

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
C345125C04
0.698,1.333 1.448,1.656 true 1.99,1.604 2.74,1.302 true 2.01,2.125 2.719,2.656 true 0.729,2.625 1.427,2.135 true 0.208,0.198 0.521,0.396 0.313,0.198 10 false *a 0.385,1.229 0.698,1.427 0.313,0.198 10 false BM1 0.333,2.583 0.76,2.813 0.427,0.229 10 false GND1 2.75,2.625 3.188,2.885 0.438,0.26 10 false GND2 2.792,1.198 3.188,1.417 0.396,0.219 10 false BM2
*a Component without harness connected
(Brake Booster Pump Assembly)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A12 brake booster pump assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BM1) - 4 (GND1) Always Below 10 Ω
1 (BM2) - 3 (GND2) Always Below 10 Ω
2 (BM1) - 1 (BM2) Always Below 1 Ω
4 (GND1) - 3 (GND2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (ACCUMULATOR PRESSURE)

NG

3.READ VALUE USING GTS (ACCUMULATOR PRESSURE)
a.

Reconnect the A12 brake booster pump assembly connector.


b.

Disconnect the A45 brake pedal stroke sensor assembly connector.


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MT Voltage Value MT voltage value Min.: 0.00 V, Max.: 20.00 V Pump motor off: 0.00 V
Pump motor on: 12.00 V
-
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped)
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > ABS/VSC/TRC > Data List
Tester Display
MT Voltage Value
Accumulator Pressure
50003 105 279,502

d.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


e.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.


Result:
Result Proceed to
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. A
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. B



A

B

4.READ VALUE USING GTS (SERVO PRESSURE)
4.READ VALUE USING GTS (SERVO PRESSURE)
a.

Turn the power switch off.


b.

Reconnect the A45 brake pedal stroke sensor assembly connector.


c.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SLR) Valve Close Linear solenoid reduction valve (SLR) Valve close ON/OFF ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Solenoid (SLR) Valve Close
50004 105 81

d.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 2.10 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > ABS/VSC/TRC > Data List
Tester Display
Servo Pressure
50003 105 501

e.

Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).


f.

Check that the servo pressure output value does not increase when performing the Active Test.

OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:

If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.



Result:
Result Proceed to
The servo pressure output value increases. A
The servo pressure output value does not increase. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE BOOSTER PUMP ASSEMBLY

for the brake booster with master cylinder assembly (for LHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL

for the brake booster with master cylinder assembly (for RHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL

for the brake booster pump assembly (for LHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP(for LHD)>REMOVAL

for the brake booster pump assembly (for RHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP(for RHD)>REMOVAL