Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1391  Abnormal Leak in Accumulator  


DESCRIPTION

This DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake actuator (brake booster with master cylinder assembly) or brake booster pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1391 Abnormal Leak in Accumulator 351 Either of the following is detected:
1.

When the brake pedal is not depressed and the pump motor is operating, the accumulator pressure sensor value does not increase a certain number of times.

2.

When the brake pedal is not depressed and the pump motor is not operating, the accumulator pressure sensor decrease rate exceeds a certain threshold a certain number of times.


·

Brake fluid leaks

·

Brake actuator (brake booster with master cylinder assembly)

(Malfunctioning internal seal etc.)

·

Brake booster pump assembly

(Accumulator internal gas pressure decrease, etc.)


Electronically controlled brake system DTC

DTC Detection Conditions: C1391 INF Code: 351
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Brake pedal not depressed and pump motor operating. ○ -
Brake pedal not depressed and pump motor not operating. - ○
Malfunction Status The accumulator pressure sensor value does not increase a certain number of times. ○ -
The accumulator pressure sensor decrease rate exceeds a certain threshold a certain number of times. - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake actuator (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS (SERVO PRESSURE)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SLR) Valve Close Linear solenoid reduction valve (SLR) Valve close ON/OFF ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ECB Solenoid (SLR) Valve Close
50004 105 81

b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 2.10 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > ABS/VSC/TRC > Data List
Tester Display
Servo Pressure
50003 105 501

c.

Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).


d.

Check that the servo pressure output value does not increase when performing the Active Test.

OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:

If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.



Result:
Result Proceed to
The servo pressure output value increases. A
The servo pressure output value does not increase. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

2.CHECK OPERATING TIME OF PUMP MOTOR
2.CHECK OPERATING TIME OF PUMP MOTOR
a.

Turn the power switch on (READY).


b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MT Voltage Value MT voltage value Min.: 0.00 V, Max.: 20.00 V Pump motor off: 0.00 V
Pump motor on: 12.00 V
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
MT Voltage Value
50003 105 279

c.

With the power switch on (READY), check the operation of the pump motor.

OK:

The pump motor operates once or more within 20 seconds or operates for 10 seconds or more each time.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR FLUID LEAK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CHECK FOR FLUID LEAK
a.

Check for brake fluid leaks in the line from the brake booster pump assembly to the brake booster with master cylinder assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1202

OK:

There are no brake fluid leaks.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE BOOSTER PUMP ASSEMBLY

for the brake booster with master cylinder assembly (for LHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL

for the brake booster with master cylinder assembly (for RHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL

for the brake booster pump assembly (for LHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP(for LHD)>REMOVAL

for the brake booster pump assembly (for RHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP(for RHD)>REMOVAL


NG

MALFUNCTIONING PART