Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1300  Skid Control ECU Malfunction  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) stores this DTC if malfunctions are found in the circuit inside the ECU by self diagnosis.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1300 Skid Control ECU Malfunction 1028 to 1049
·

INF Code: 1028 to 1041, 1043 to 1044, 1046 to 1049

·

Skid control ECU (brake booster with master cylinder assembly) internal malfunction.


·

INF Code: 1042

·

Sudden drop of power source voltage or skid control ECU (brake booster with master cylinder assembly) internal malfunction.


·

INF Code: 1045

·

An open is detected in the brake booster pump assembly circuit or skid control ECU (brake booster with master cylinder assembly) internal malfunction.



·

INF Code: 1028 to 1041, 1043 to 1044, 1046 to 1049

·

Skid control ECU (brake booster with master cylinder assembly)


·

INF Code: 1042

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (brake booster with master cylinder assembly)


·

INF Code: 1045

·

Brake booster pump assembly

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)



Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
A brake booster pump assembly circuit malfunction DTC is output with DTC C1300. A
DTC C1300 is output. B



A

B

2.CHECK FREEZE FRAME DATA
2.CHECK FREEZE FRAME DATA
a.

Check the INF code from the Freeze Frame Data stored when DTC (C1300) was stored.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>FREEZE FRAME DATA

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
INF codes 1028 to 1041, 1043 to 1044 or 1046 to 1049 are output. A
INF code 1042 is output. B
INF code 1045 is output. C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

3.CHECK FREEZE FRAME DATA

C

6.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
3.CHECK FREEZE FRAME DATA
a.

Using the GTS, read the "IG1 Voltage Value", "IG2 Voltage Value", "BS1 Voltage Value", "BS2 Voltage Value", "VM1 Voltage Value" and "VM2 Voltage Value" of the Freeze Frame Data stored when the DTC C1300 (INF code 1042) was stored.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>FREEZE FRAME DATA

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
Any of the voltage values of the Freeze Frame Data are 7.00 V or less. A
All of the voltage values of the Freeze Frame Data are 12.00 V or more. B


HINT:

If any of the voltage values of the Freeze Frame Data are 7.00 V or less, a sudden drop of the power source voltage is suspected as a cause of the DTC output.

In this case, inspect the auxiliary battery and replace or recharge the auxiliary battery as necessary.




A

4.CHECK AUXILIARY BATTERY

B

5.CHECK AUXILIARY BATTERY
4.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

END

NG

CHARGE OR REPLACE AUXILIARY BATTERY

5.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

CHARGE OR REPLACE AUXILIARY BATTERY

6.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
C345125C05
0.698,1.333 1.448,1.656 true 1.99,1.604 2.74,1.302 true 2.01,2.125 2.719,2.656 true 0.729,2.625 1.427,2.135 true 0.208,0.198 0.521,0.396 0.313,0.198 10 false *a 0.385,1.229 0.698,1.427 0.313,0.198 10 false BM1 0.344,2.583 0.771,2.813 0.427,0.229 10 false GND1 2.75,2.625 3.188,2.885 0.438,0.26 10 false GND2 2.792,1.198 3.188,1.417 0.396,0.219 10 false BM2
*a Component without harness connected
(Brake Booster Pump Assembly)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A12 brake booster pump assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BM1) - 4 (GND1) Always Below 10 Ω
1 (BM2) - 3 (GND2) Always Below 10 Ω
2 (BM1) - 1 (BM2) Always Below 1 Ω
4 (GND1) - 3 (GND2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

7.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C345124C02
0.354,1.01 0.76,1.281 0.406,0.271 0.865,2.958 1.521,2.479 true 1.906,2.469 2.719,2.958 true 0.229,0.25 0.542,0.406 0.313,0.156 10 false *a 0.438,1.063 0.896,1.26 0.458,0.198 10 false A12 0.646,2.979 1.104,3.177 0.458,0.198 10 false GND2 2.615,2.979 3.073,3.177 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Booster Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A12-4 (GND1) - Body ground Always Below 1 Ω
A12-3 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-1 (MRO1) - A12-2 (BM1) Always Below 1 Ω
A41-1 (MRO1) or A12-2 (BM1) - Body ground Always 10 kΩ or higher
A41-27 (MRO2) - A12-1 (BM2) Always Below 1 Ω
A41-27 (MRO2) or A12-1 (BM2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR