Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1403  Malfunction in Rear Speed Sensor RH Circuit  C1404  Malfunction in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1415 and C1416.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1415

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1403 Malfunction in Rear Speed Sensor RH Circuit 521
522
527
·

INF Code: 521

·

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.


·

INF Code: 522

·

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).


·

INF Code: 527

·

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.



·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Speed sensor installed improperly

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)


ABS DTC
C1404 Malfunction in Rear Speed Sensor LH Circuit 531
532
537
·

INF Code: 531

·

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.


·

INF Code: 532

·

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).


·

INF Code: 537

·

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.



·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Speed sensor installed improperly

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)


ABS DTC

PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor
*a OK
*b NG
*c No Clearance


Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

b.

Check the speed sensor output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT SKID CONTROL SENSOR WIRE
3.INSPECT SKID CONTROL SENSOR WIRE
a.
C251359C27
0.583,0.51 0.979,0.75 0.396,0.24 0.583,0.833 0.979,1.073 0.396,0.24 2.083,0.51 2.479,0.75 0.396,0.24 2.083,0.844 2.479,1.083 0.396,0.24 0.833,1.979 0.563,2.76 true 1.094,1.979 1.417,2.75 true 2.344,2.052 2.188,2.531 true 2.573,2.052 2.76,2.531 true 0.188,0.177 0.646,0.469 0.458,0.292 10 false *a 0.875,1.219 1.375,1.51 0.5,0.292 10 false *b 2.385,1.219 2.906,1.531 0.521,0.313 10 false *c 1.031,0.573 1.427,0.854 0.396,0.281 10 false *A 1.042,0.896 1.5,1.229 0.458,0.333 10 false *B 0.698,0.542 1.042,0.781 0.344,0.24 10 false g1 0.729,0.865 1.156,1.083 0.427,0.219 10 false f1 2.542,0.573 2.948,0.844 0.406,0.271 10 false *A 2.531,0.896 3.01,1.156 0.479,0.26 10 false *B 2.146,0.542 2.573,0.75 0.427,0.208 10 false gM1 2.177,0.875 2.615,1.083 0.438,0.208 10 false fM1 0.333,2.781 0.917,3.021 0.583,0.24 10 false RR-*A 0.333,2.948 1.115,3.188 0.781,0.24 10 false RL-*B 1.25,2.771 1.844,3.01 0.594,0.24 10 false RR+*A 1.25,2.948 1.854,3.146 0.604,0.198 10 false RL+*B 1.958,2.552 2.531,2.771 0.573,0.219 10 false RR+*A 1.948,2.719 2.594,2.938 0.646,0.219 10 false RL+*B 2.615,2.552 3.26,2.729 0.646,0.177 10 false RR-*A 2.615,2.719 3.271,2.948 0.656,0.229 10 false RL-*B
*A for RH
*B for LH
*a Front view of rear skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the rear skid control sensor wire RH or the rear skid control sensor wire LH.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
g1-2 (RR+) - gM1-1 (RR+) Always Below 1 Ω
g1-2 (RR+) - gM1-2 (RR-) Always 10 kΩ or higher
g1-2 (RR+) or gM1-1 (RR+) - Body ground Always 10 kΩ or higher
g1-1 (RR-) - gM1-2 (RR-) Always Below 1 Ω
g1-1 (RR-) - gM1-1 (RR+) Always 10 kΩ or higher
g1-1 (RR-) or gM1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
f1-2 (RL+) - fM1-1 (RL+) Always Below 1 Ω
f1-2 (RL+) - fM1-2 (RL-) Always 10 kΩ or higher
f1-2 (RL+) or fM1-1 (RL+) - Body ground Always 10 kΩ or higher
f1-1 (RL-) - fM1-2 (RL-) Always Below 1 Ω
f1-1 (RL-) - fM1-1 (RL+) Always 10 kΩ or higher
f1-1 (RL-) or fM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

REPLACE SKID CONTROL SENSOR WIRE

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A41-7 (RR+) - gM1-1 (RR+) Always Below 1 Ω
A41-7 (RR+) or gM1-1 (RR+) - Body ground Always 10 kΩ or higher
A41-8 (RR-) - gM1-2 (RR-) Always Below 1 Ω
A41-8 (RR-) or gM1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A41-34 (RL+) - fM1-1 (RL+) Always Below 1 Ω
A41-34 (RL+) or fM1-1 (RL+) - Body ground Always 10 kΩ or higher
A41-35 (RL-) - fM1-2 (RL-) Always Below 1 Ω
A41-35 (RL-) or fM1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.


HINT:

The rear speed sensor and rear speed sensor rotor are incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor and rear speed sensor rotor need to be replaced, replace the rear axle hub and bearing assembly.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR