Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1415  Rear Speed Sensor RH Circuit Output  C1416  Rear Speed Sensor LH Circuit Output  


DESCRIPTION

Each speed sensor detects the wheel speed and sends the signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for ABS control.

HINT:

The output voltage values shown below are for when the vehicle wire harnesses are connected to the skid control ECU (brake booster with master cylinder assembly) and the speed sensors.


C151818E48
1.573,0.854 1.573,0.469 1.573,0.469 1.448,0.469 false 0.531,0.365 1.646,0.74 1.115,0.375 10 false Speed Sensor 4.021,2.115 4.729,2.281 0.708,0.167 10 false Low speed 6.083,1.281 6.448,1.448 0.365,0.167 10 false 1.4 V 6.083,1.625 6.563,1.792 0.479,0.167 10 false 0.7 V 4.99,2.115 5.719,2.281 0.729,0.167 10 false High speed 0.969,2.177 2.26,2.344 1.292,0.167 10 false Speed Sensor Rotor

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1415 Rear Speed Sensor RH Circuit Output 524
543
·

INF Code: 524

·

An open in the sensor signal of a malfunctioning wheel occurs 255 times or more.


·

INF Code: 543

·

Either of the following is detected:

1.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

2.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.




·

Skid control sensor wire RH

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Speed sensor installed improperly

·

Wire harness or connector

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC
C1416 Rear Speed Sensor LH Circuit Output 534
544
·

INF Code: 534

·

An open in the sensor signal of a malfunctioning wheel occurs 255 times or more.


·

INF Code: 544

·

Either of the following is detected:

1.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

2.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.




·

Skid control sensor wire LH

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Speed sensor installed improperly

·

Wire harness or connector

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC

DTC Detection Conditions: C1415 INF Code: 543
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more. ○ -
At a vehicle speed of 10 km/h (6 mph) or more. - ○
Malfunction Status Noise occurs in the sensor signals of a malfunctioning wheel. ○ -
Noise occurs once per rotor rotation. - ○
Detection Time Detected 75 times or more within 5 seconds 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1416 INF Code: 544
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more. ○ -
At a vehicle speed of 10 km/h (6 mph) or more. - ○
Malfunction Status Noise occurs in the sensor signals of a malfunctioning wheel. ○ -
Noise occurs once per rotor rotation. - ○
Detection Time Detected 75 times or more within 5 seconds 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C351996E02
1.313,0.844 1.771,1.042 0.458,0.198 10 false g1 1.365,0.646 1.823,0.844 0.458,0.198 10 false 2 2.417,0.844 2.875,1.042 0.458,0.198 10 false gM1 2.51,0.635 2.969,0.833 0.458,0.198 10 false 1 2.531,1.344 2.99,1.542 0.458,0.198 10 false 2 2.427,1.552 2.885,1.75 0.458,0.198 10 false gM1 1.313,1.542 1.771,1.74 0.458,0.198 10 false g1 1.354,1.344 1.813,1.542 0.458,0.198 10 false 1 4.323,2.198 4.781,2.396 0.458,0.198 10 false * 4.313,4.604 4.771,4.802 0.458,0.198 10 false * 5.646,0.771 6.104,0.969 0.458,0.198 10 false 7 5.813,0.969 6.271,1.167 0.458,0.198 10 false RR+ 5.646,1.448 6.104,1.646 0.458,0.198 10 false 8 5.813,1.635 6.271,1.833 0.458,0.198 10 false RR- 5.583,3.156 6.042,3.354 0.458,0.198 10 false 34 5.823,3.365 6.281,3.563 0.458,0.198 10 false RL+ 5.583,3.833 6.042,4.031 0.458,0.198 10 false 35 5.813,4.031 6.271,4.229 0.458,0.198 10 false RL- 2.51,3.042 2.969,3.24 0.458,0.198 10 false 1 2.458,3.25 2.917,3.448 0.458,0.198 10 false fM1 2.531,3.74 2.99,3.938 0.458,0.198 10 false 2 2.448,3.948 2.906,4.146 0.458,0.198 10 false fM1 1.333,3.958 1.792,4.156 0.458,0.198 10 false f1 1.354,3.74 1.813,3.938 0.458,0.198 10 false 1 1.344,3.26 1.802,3.458 0.458,0.198 10 false f1 1.365,3.042 1.823,3.24 0.458,0.198 10 false 2 0.448,1.958 1.24,2.323 0.792,0.365 10 false Rear Speed Sensor RH 1.479,1.958 2.75,2.333 1.271,0.375 10 false Skid Control Sensor Wire RH 0.448,4.365 1.24,4.74 0.792,0.375 10 false Rear Speed Sensor LH 1.5,4.375 2.781,4.781 1.281,0.406 10 false Skid Control Sensor Wire LH 1.792,5.156 2.688,5.396 0.896,0.24 10 false *: Shielded 5.094,4.948 5.552,5.146 0.458,0.198 10 false A41 5.073,5.125 7.135,5.5 2.063,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.031,0.854 2.49,1.052 0.458,0.198 10 false RR+ 1.625,0.854 2.083,1.052 0.458,0.198 10 false RR+ 0.865,0.854 1.323,1.052 0.458,0.198 10 false RR+ 2.042,1.563 2.5,1.76 0.458,0.198 10 false RR- 1.625,1.563 2.083,1.76 0.458,0.198 10 false RR- 0.885,1.563 1.344,1.76 0.458,0.198 10 false RR- 2.063,3.26 2.521,3.458 0.458,0.198 10 false RL+ 1.625,3.26 2.083,3.458 0.458,0.198 10 false RL+ 0.885,3.26 1.344,3.458 0.458,0.198 10 false RL+ 2.063,3.948 2.521,4.146 0.458,0.198 10 false RL- 1.625,3.948 2.083,4.146 0.458,0.198 10 false RL- 0.896,3.958 1.354,4.156 0.458,0.198 10 false RL-

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Sensor Voltage Open
RL Speed Sensor Voltage Open
50003 105 296,297

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

b.

Check the speed sensor output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1415 and C1416 are not output. A
DTCs C1415 and/or C1416 are output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK REAR SPEED SENSOR INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor
*a OK
*b NG
*c No Clearance


Turn the power switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



Result:
Proceed to
OK
NG



OK

5.INSPECT SKID CONTROL SENSOR WIRE

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

5.INSPECT SKID CONTROL SENSOR WIRE
a.
C251359C27
0.583,0.51 0.979,0.75 0.396,0.24 0.583,0.833 0.979,1.073 0.396,0.24 2.083,0.51 2.479,0.75 0.396,0.24 2.083,0.844 2.479,1.083 0.396,0.24 0.833,1.979 0.563,2.76 true 1.094,1.979 1.417,2.75 true 2.344,2.052 2.188,2.531 true 2.573,2.052 2.76,2.531 true 0.188,0.177 0.646,0.469 0.458,0.292 10 false *a 0.875,1.219 1.375,1.51 0.5,0.292 10 false *b 2.385,1.219 2.906,1.531 0.521,0.313 10 false *c 1.031,0.573 1.427,0.854 0.396,0.281 10 false *A 1.042,0.896 1.5,1.229 0.458,0.333 10 false *B 0.698,0.542 1.042,0.781 0.344,0.24 10 false g1 0.729,0.865 1.156,1.083 0.427,0.219 10 false f1 2.542,0.573 2.948,0.844 0.406,0.271 10 false *A 2.531,0.896 3.01,1.156 0.479,0.26 10 false *B 2.146,0.542 2.573,0.75 0.427,0.208 10 false gM1 2.177,0.875 2.615,1.083 0.438,0.208 10 false fM1 0.333,2.781 0.917,3.021 0.583,0.24 10 false RR-*A 0.333,2.948 1.115,3.188 0.781,0.24 10 false RL-*B 1.25,2.771 1.844,3.01 0.594,0.24 10 false RR+*A 1.25,2.948 1.854,3.146 0.604,0.198 10 false RL+*B 1.958,2.552 2.531,2.771 0.573,0.219 10 false RR+*A 1.948,2.719 2.594,2.938 0.646,0.219 10 false RL+*B 2.615,2.552 3.26,2.729 0.646,0.177 10 false RR-*A 2.615,2.719 3.271,2.948 0.656,0.229 10 false RL-*B
*A for RH
*B for LH
*a Front view of rear skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Remove the rear skid control sensor wire RH or the rear skid control sensor wire LH.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
g1-2 (RR+) - gM1-1 (RR+) Always Below 1 Ω
g1-2 (RR+) - gM1-2 (RR-) Always 10 kΩ or higher
g1-2 (RR+) or gM1-1 (RR+) - Body ground Always 10 kΩ or higher
g1-1 (RR-) - gM1-2 (RR-) Always Below 1 Ω
g1-1 (RR-) - gM1-1 (RR+) Always 10 kΩ or higher
g1-1 (RR-) or gM1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
f1-2 (RL+) - fM1-1 (RL+) Always Below 1 Ω
f1-2 (RL+) - fM1-2 (RL-) Always 10 kΩ or higher
f1-2 (RL+) or fM1-1 (RL+) - Body ground Always 10 kΩ or higher
f1-1 (RL-) - fM1-2 (RL-) Always Below 1 Ω
f1-1 (RL-) - fM1-1 (RL+) Always 10 kΩ or higher
f1-1 (RL-) or fM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

REPLACE SKID CONTROL SENSOR WIRE

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A41-7 (RR+) - gM1-1 (RR+) Always Below 1 Ω
A41-7 (RR+) or gM1-1 (RR+) - Body ground Always 10 kΩ or higher
A41-8 (RR-) - gM1-2 (RR-) Always Below 1 Ω
A41-8 (RR-) or gM1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A41-34 (RL+) - fM1-1 (RL+) Always Below 1 Ω
A41-34 (RL+) or fM1-1 (RL+) - Body ground Always 10 kΩ or higher
A41-35 (RL-) - fM1-2 (RL-) Always Below 1 Ω
A41-35 (RL-) or fM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C251360C41
0.323,0.917 0.802,1.24 0.479,0.323 1.802,0.917 2.281,1.24 0.479,0.323 2.656,2.188 2.979,2.719 true 1.177,2.188 1.5,2.719 true 0.26,0.26 0.771,0.635 0.51,0.375 10 false *a 0.438,0.979 1.042,1.281 0.604,0.302 10 false gM1 1.927,0.99 2.385,1.24 0.458,0.25 10 false fM1 1.396,2.75 2.177,3.021 0.781,0.271 10 false RR+ 2.917,2.75 3.344,2.979 0.427,0.229 10 false RL+ 0.854,1 1.167,1.156 0.313,0.156 10 false *A 2.344,1 2.656,1.156 0.313,0.156 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Skid Control Sensor Wire)


Reconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
gM1-1 (RR+) - Body ground Power switch on (IG) 8 to 14 V

for LH
Tester Connection Condition Specified Condition
fM1-1 (RL+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor and rear speed sensor rotor are incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor and rear speed sensor rotor need to be replaced, replace the rear axle hub and bearing assembly.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY