Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  TRC does not Operate  


DESCRIPTION

When ABS, TRC or VSC is operating, the skid control ECU (brake booster with master cylinder assembly) blinks the slip indicator light to inform the driver that slippage occurred.

When in VSC off mode, or TRC and VSC are disabled, the multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates to inform the driver.

When a communication malfunction with the hybrid vehicle control ECU is detected, TRC and VSC are disabled. Also when the system is malfunctioning, TRC and VSC are disabled and the indicator lights of related systems illuminate.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.BRAKE PROBLEM CHECK
a.

Check if the slip indicator light was illuminated when TRC did not operate.

OK:

The slip indicator light was illuminated.


HINT:

When a DTC is stored, the slip indicator light is illuminated and TRC does not operate due to the fail-safe function.



b.

Check the operation condition of the VSC OFF switch (combination switch assembly) when TRC did not operate.

OK:

The VSC OFF switch (combination switch assembly) had been operated to turn off TRC when TRC did not operate.


HINT:

When the multi-information display in the combination meter assembly displays "Traction Control Turned Off", TRC does not operate.



Result:
Proceed to
OK
NG



OK

END

NG

2.CHECK DTC
2.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check the DTCs (electronically controlled brake system) that are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs are not output. A
Electronically controlled brake system DTCs are output. B



A

3.CHECK VEHICLE

B

3.CHECK VEHICLE
a.

Operate the VSC OFF switch (combination switch assembly) and check that the multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates in accordance with the operation of the switch.

OK:

The multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates in accordance with the operation of the switch.



Result:
Proceed to
OK
NG



OK

4.PERFORM TEST MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CIRCUIT)

NG

4.PERFORM TEST MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CIRCUIT)
a.

Using the GTS, perform a Test Mode (Signal Check) inspection sensor check and check that speed sensor Test Mode (Signal Check) inspection items change from incomplete to complete.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 4359
OK:

Speed sensor Test Mode (Signal Check) inspection items change from incomplete to complete.



Result:
Proceed to
OK
NG



OK

5.PERFORM OPERATION CHECK DRIVING

NG

INSPECT AND REPAIR MALFUNCTIONING SPEED SENSOR CIRCUIT

5.PERFORM OPERATION CHECK DRIVING
a.

Operate the VSC OFF switch (combination switch assembly) and check that the system is not in TRC off mode or VSC off mode.


b.

Check that no DTCs are output and that each warning light is not illuminated.


c.

Start off the vehicle on a low friction surface and check that TRC operates when attempting to make the drive wheels slip.

OK:

TRC operates when slip occurs when starting off.


NOTICE:
·

Even when the system is normal, VSC may not operate when the vehicle speed is low or TRC may not operate due to a malfunction. Make sure that only the drive wheels slip during the procedure.

·

When confirming that the slip indicator light blinks, do not slip the drive wheels longer than necessary. Whether TRC operated or not can be checked by reading the Freeze Frame Data when the system operated.

·

Pay attention to your surroundings when performing the procedure and depress the accelerator pedal with caution.




Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY