Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C14B3  Reaction Force Pressure Sensor Zero Point Malfunction  


DESCRIPTION

The reaction force pressure sensor detects and outputs the brake fluid pressure of the stroke simulator, which changes in accordance with brake pedal operation, to the skid control ECU (brake booster with master cylinder assembly).

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C14B3 Reaction Force Pressure Sensor Zero Point Malfunction 204 When the brake pedal is not depressed, the reaction force pressure sensor output value is -0.63 MPa (-6.4 kgf/cm2, -91.4 psi) or less or 1.53 MPa (15.6 kgf/cm2, 222 psi) or more for 3 seconds or more. Skid control ECU (brake booster with master cylinder assembly) Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (REACTION FORCE PRESSURE)
2.READ VALUE USING GTS (REACTION FORCE PRESSURE)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reaction Force Pressure Pressure value of stroke simulator Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > ABS/VSC/TRC > Data List
Tester Display
Reaction Force Pressure
50003 105 500

b.

Check that the reaction force pressure sensor output value is within 0.00 to 1.53 MPa when the brake pedal is not depressed.

OK:

The reaction force pressure sensor output value is within 0.00 to 1.53 MPa.


HINT:

If the reaction force pressure sensor output value is within 0.00 to 1.53 MPa, the skid control ECU (brake booster with master cylinder assembly) automatically performs zero point calibration every time the power switch is turned on (IG).

Therefore, if the reaction force pressure sensor output value is not within 0.00 to 1.53 MPa, replace the skid control ECU (brake booster with master cylinder assembly) with a new one.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

Even if the DTC is cleared, it will immediately be output again if the reaction force pressure sensor zero point malfunction remains.



Result:
Result Proceed to
DTC C14B3 is not output. A
DTC C14B3 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY