Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3210E _59 Vehicle Exterior _047533 LIGHTING (EXT) _0244228 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Hazard Warning Switch Circuit  


DESCRIPTION

The combination meter assembly receives the hazard warning signal switch on signal and controls the operation of the hazard warning lights.

WIRING DIAGRAM

E343094E04
5.042,1.74 6.885,2.146 1.844,0.406 10 false Combination Meter Assembly (Meter Circuit Plate) 1.104,1.885 2.531,2.271 1.427,0.385 10 false Hazard Warning Signal Switch Assembly 1.094,1.708 1.625,1.885 0.531,0.177 10 false Z1 2.073,0.833 2.51,1.104 0.438,0.271 10 false TB 2.354,0.833 2.792,1.104 0.438,0.271 10 false 5 5.594,0.948 6.031,1.219 0.438,0.271 10 false HAZ 5.333,0.833 5.771,1.104 0.438,0.271 10 false 10 5.042,1.563 5.479,1.833 0.438,0.271 10 false F7 0.958,0.833 1.167,1.01 0.208,0.177 10 false 4 1.135,0.833 1.344,1.01 0.208,0.177 10 false E

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hazard Flasher Switch Hazard warning signal switch signal ON or OFF ON: Hazard warning signal switch on
OFF: Hazard warning signal switch off
-
Body Electrical > Combination Meter > Data List
Tester Display
Hazard Flasher Switch
50003 122 99
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
a.

Remove the hazard warning signal switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>REMOVAL


b.

Inspect the hazard warning signal switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) AND BODY GROUND)

NG

REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) AND BODY GROUND)
a.

Disconnect the F7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-5 (TB) - F7-10 (HAZ) Always Below 1 Ω
Z1-5 (TB) or F7-10 (HAZ) - Body ground Always 10 kΩ or higher
Z1-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR