Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3210E _59 Vehicle Exterior _047533 LIGHTING (EXT) _0244228 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Parking Brake Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the parking brake switch assembly.

WIRING DIAGRAM

E259671E08
5.479,2 7.135,2.354 1.656,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 4.26,1.052 5.906,1.385 1.646,0.333 10 false Instrument Panel Junction Block Assembly 1.24,1.219 3.292,1.385 2.052,0.167 10 false Parking Brake Switch Assembly 4.375,0.75 4.594,0.927 0.219,0.177 10 false 3F 4.375,0.552 4.615,0.729 0.24,0.177 10 false 18 5.74,0.635 5.917,0.792 0.177,0.156 10 false 12 5.99,0.75 6.302,0.896 0.313,0.146 10 false PKB 5.479,1.854 5.719,2 0.24,0.146 10 false MB 1.24,1.052 1.563,1.229 0.323,0.177 10 false A49 2.698,0.646 2.802,0.823 0.104,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulliten.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch signal ON or OFF ON: Parking brake switch on
OFF: Parking brake switch off
-
Body Electrical > Main Body > Data List
Tester Display
Parking Brake SW
50003 123 12
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the parking brake switch assembly.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL


b.

Inspect the parking brake switch assembly.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3F instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-1 - 3F-18 Always Below 1 Ω
A49-1 - or 3F-18 Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E344206C03
1.24,0.198 1.583,0.396 0.344,0.198 4.563,0.51 4.906,0.708 0.344,0.198 4.521,1.458 4.271,1.125 false 0.135,0.167 0.354,0.344 0.219,0.177 10 false *a 4.427,1.469 4.885,1.667 0.458,0.198 10 false PKB 4.625,0.531 4.938,0.729 0.313,0.198 10 false MB 1.333,0.229 1.646,0.427 0.313,0.198 10 false 3F
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3F-18 - MB-12 (PKB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY