Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SRS SEAT CUSHION AIRBAG ASSEMBLY
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0245203 SRS SEAT CUSHION AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  SRS SEAT CUSHION AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front seat cushion airbag assembly RH removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Removal/installation of the front passenger seat*1 Zero point calibration (Occupant classification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

*1: w/ Occupant Classification System

CAUTION:
B394719

·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:

If the front seat cushion airbag assembly RH has been deployed, replace the front seat cushion airbag assembly RH, front seat adjuster assembly RH, separate type front seat cushion pad and separate type front seat cushion cover with the necessary parts in accordance with the extent of the collision damage.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL


Hide 71073S 2.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 72551 3.REMOVE NO. 1 RECLINING HINGE COVER

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 72525A 4.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 71811D 5.REMOVE FRONT SEAT CUSHION SHIELD RH

Hide 71861 6.REMOVE FRONT SEAT INNER CUSHION SHIELD RH

Hide 7.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 8.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 739F0 9.REMOVE FRONT SEAT CUSHION AIRBAG ASSEMBLY RH

CAUTION:
B417762C01
0,0 0,0 false
V100155

Deployment Side


When storing the front seat cushion airbag assembly RH, keep the airbag deployment side facing upward.


a.
B432348

Disengage the 2 clamps and claw.

HINT:

Disengage the clamps first.



b.

Remove the 3 nuts.

NOTICE:
·

The nuts must not be reused.

·

Make sure that the front seat adjuster assembly RH is not deformed. If it is, replace it with a new one.




c.
B432349

Pass the airbag wire harness through the hole to remove the front seat cushion airbag assembly RH.